Table of Contents
Advertisement
42
EN
O n-Screen
Timer
Progra mm ing
Turn on the TV and select the VCR channel 3 or 4 (or AV
mode).
N U M BER
N U M BER "8"
REW
M EN U
When Using The Illumi-Guide Feature
● Buttons light or blink on the remote control for
approximately 10 seconds. If the button or buttons extinguish
during timer programming, press ILLUMI GUIDE and the
button or buttons previously lit or blinking come back on. If
the button or buttons do not re-light or start blinking again,
press M EN U as many times as necessary to return to the
normal screen and extinguish all illuminated buttons,
and re-perform the timer programming procedure from the
beginning.
● If for some reason the remote control's signal is not received
by the VCR, press M EN U as many times as necessary to
return to the normal screen and extinguish all
illuminated buttons, and re-perform the timer programming
procedure from the beginning.
Downloaded from:
https://www.usersmanualguide.com/
q
1
2
3
4
5
6
N U M BER "9"
9
7
8
TIM ER
0
CH
TV/ CABLE/ VCR
FF
O K
PU SH JO G
ILLU M I GU ID E
TIM ER RECO RD IN G (cont.)
You can directly program the VCR's timer to record up to 8
shows, as far as a year in advance. Remember, the clock must be
set before you can program the timer (
use the optional Illumi-Guide feature, where the relevant buttons
on the remote control light to tell you which button to press next.
The Illumi-Guide feature is activated by the ILLU M I GU ID E
button on the remote control. The Illumi-Guide feature is only
active when the remote control's TV/ CABLE/ VCR switch is set to
"VCR". (Illumi-Guide is an optional help feature which makes
programming easier. It is not necessary to use Illumi-Guide to
program the VCR.)
LO AD A CASSETTE
Make sure the record safety tab is intact. If not, cover
1
the hole with adhesive tape, then load it into the VCR.
● The VCR comes on, and the counter is reset,
automatically.
ACCESS O N -SCREEN
MEN U
To use the Illumi-Guide feature press ILLU M I GU ID E .
2
The M EN U , REW , PLAY and FF buttons will light.
Press M EN U as many times as necessary to bring up the
Main Menu screen.
● If you are using the Illumi-Guide feature,
when the following buttons are lit: NUMBER keys (0-9),
PUSH J OG , CANCEL and MENU .
ACCESS PRO GRAM SET
SCREEN
Make sure the highlight bar (arrow) is on "PROGRAM
3
SET", then press O K .
● If you are using the Illumi-Guide feature,
when the following buttons are lit: N U M BER keys (0
– 9), PU SH JO G , CAN CEL and M EN U .
SELECT PROGRAM N UMBER
Press the appropriate
4
NUMBER keys or CH
or PU SH JO G 5 ∞ to select
a vacant program number,
then press OK . The first time
you set the timer program-
ming function, all the
program numbers will be
blank; in this case just press
OK when the Program Set screen appears.
● If you are using the Illumi-Guide feature,
when the following buttons are lit: N U M BER keys
(0 – 9), PU SH JO G , CAN CEL and M EN U .
pg. 5 or 7).You can also
OK blinks
O K blinks
PROGRAM 1
5 ∞
DATE
– –/– –
START
– –:– – AM
STOP
– –:– – AM
CHANNEL
– – SP
PRESS NUMBER KEY (O–9)
OR (5,∞), THEN (OK)
PRESS (MENU) TO END
O K blinks
Advertisement
Table of Contents
