Table of Contents
Advertisement
Quick Links
INSTALLATION
& OPERATION
MANUAL
S
V
TL
UPER
ISOR
™
SuperVisorTL™
Interior Lighting System
Ford Crown Victoria
2006 Model
CONTENTS:
Introduction .......................................................................... 2
Unpacking & Pre-Installation ................................................ 2
Installation & Mounting ..................................................... 3-7
Wiring Diagram .................................................................... 5
Wiring Instructions & Fusing ................................................ 6
LED Flash Pattern Selection & Troubleshooting .................. 7
Exploded View & Parts List ................................................. 8
Notes ............................................................................ 19-11
Warranty ............................................................................ 1 2
For future reference record your product's serial no. here __________________________________________
IMPORTANT:
Read all instructions and warnings before installing and using.
This manual must be delivered to the end user of this equipment.
INSTALLER:
Advertisement
Table of Contents
Related Manuals for Code 3 SuperVisorTL
Summary of Contents for Code 3 SuperVisorTL
-
Page 1: Table Of Contents
INSTALLATION & OPERATION MANUAL UPER ISOR ™ SuperVisorTL™ Interior Lighting System Ford Crown Victoria 2006 Model CONTENTS: Introduction ................2 Unpacking & Pre-Installation ..........2 Installation & Mounting ............. 3-7 Wiring Diagram ..............5 Wiring Instructions & Fusing ..........6 LED Flash Pattern Selection &... -
Page 2: Introduction
Unpacking & Pre-installation Carefully remove the SuperVisorTL™ and place it on a flat surface, taking care not to scratch the lenses or damage the cable coming out of the side. Examine the unit for transit damage, broken lamps, etc. Report any damage to the carrier and keep the shipping carton. -
Page 3: Installation & Mounting
Mounting Hardware - All mounting hardware is packed in a small box inside the main carton. There are four brackets used to mount the SuperVisorTL™ to the vehicle. These are discussed in detail later. Step 1-Removing Sun Visors Begin the installation by removing the Crown Victoria's driver and passenger sun visors. - Page 4 Carefully move the SuperVisorTL into position by tilting one end up with the front outer tip of the SuperVisorTL in front of the corner post of the Crown Vic as shown in Figure 9, then swing the other end up into position being very...
-
Page 5: Wiring Diagram
Wiring Diagram... -
Page 6: Wiring Instructions & Fusing
Wiring Instructions Larger wires and tight connections will provide longer service life for components. For high current wires it is highly recommended that terminal blocks or soldered connections be used with shrink tubing to protect the connections. Do not use insulation displacement connectors (e.g. 3M Scotchlock type connectors). -
Page 7: Led Flash Pattern Selection & Troubleshooting
Directional module Flash Pattern - Table 2 CycleFlash (DEFAULT) Quad Pop Flash75 NFPA QuadFlash75 Triple Pop Flash75 Steadyburn SingleFlash375 ModelFlash SingleFlash250 ActiveFlash SingleFlash150 FiveFlash70 FiveFlash150 QuadFlash70 QuadFlash150 TripleFlash70 DoubleFlash150 DoubleFlash70 TripleFlash150 SingleFlash75 Momentarily short and release to change patterns Flash Pattern Header for OPTIX/LEDX Troubleshooting All SuperVisorTLs are thoroughly tested prior to shipment. -
Page 8: Exploded View & Parts List
Parts List Reference Number Part Description Part Number *LED Module *Contact Code 3, Inc for P/N Chassis T14712 Outer Panel T14711 Inner Mtg. Brkt. Crown Vic T14708 Outer Mtg. Brkt. Crown Vic Pass Side T14710 Outer Mtg. Brkt. Crown Vic Drivr Side... - Page 9 Notes...
- Page 10 Notes...
Need help?
Do you have a question about the SuperVisorTL and is the answer not in the manual?
Questions and answers