Powering Up & Setting Up The Ht-R510 - Onkyo HT-R510 Instruction Manual

Powering Up & Setting Up the HT-R510
STANDBY/ON
DIGITAL INPUT TAPE
STANDBY/ON
STANDBY
A SPEAKERS B DISPLAY DIMMER DIGITAL INPUT
PHONES
AUDIO
DVD VIDEO
SELECTOR
VCR
Input selector buttons
Powering Up the HT-R510
Before connecting the power cord, connect all your speakers
and AV components (see page 10 to page 23).
1
Connect the power cord to a suit-
able wall outlet.
Turning on the HT-R510 may cause a
momentary power surge that might inter-
fere with other electrical equipment on
the same circuit. If this is a problem, plug
the HT-R510 into a different branch cir-
cuit.
2 Press the [STANDBY/ON] button.
STANDBY/ON
The HT-R510 comes on, the display
lights up, and the STANDBY indicator
goes off.
To turn off the HT-R510, press the
Remote controller
[STANDBY/ON] button. The HT-R510
will enter Standby mode. To prevent any
loud surprises the next time you turn on
your HT-R510, always turn down the vol-
ume before turning it off.
Important—Assigning Digital Inputs to
Input Sources
With this function you can assign AV components (i.e., input
sources) with digital audio outputs to the HT-R510's digital
inputs. You only need to change these assignments if your
connections don't match the default assignments listed in the
following table.
Input source
DVD
VIDEO 1
VIDEO 2
VIDEO 3
TAPE
CD
24
STANDBY/ON
MASTER VOLUME
DIRECT STEREO
SURROUND DSP
PRESET/ADJUST
SUBWOOFER
MODE MEMORY FM MODE TUNING SPEAKER ADJUST AUDIO ADJUST
CLEAR
VIDEO 3 INPUT
1 VIDEO 2 VIDEO 3 TAPE TUNER C D
S VIDEO VIDEO L AUDIO
DIGITAL INPUT
COAXIAL
Not assigned
OPTICAL 2
Not assigned
Not assigned
OPTICAL 1
If, for example, you connect your DVD player's optical dig-
ital audio output to the HT-R510's OPTICAL 1 DIGITAL
INPUT, you'll need to change the DVD input source assign-
ment from COAXIAL to OPTICAL 1.
You can change the assignments as follows.
1
CABLE/SAT
R VIDEO 1
DVD
CD/DVD
VCR
TAPE
2
DIGITAL INPUT
3
DIGITAL INPUT
If you've connected a MiniDisc recorder to the TAPE
inputs, you can set the HT-R510 so that "MD" appears on
the display instead of "TAPE." Simply press and hold the
[TAPE] button until "MD" appears (about two seconds).
Notes:
• For AV components that are connected to only analog
inputs, choose the "– – – –" setting.
• If you don't press the [DIGITAL INPUT] button for three
seconds, the previous display reappears.
• You can also specify a signal format for the DIGITAL
INPUTs (page 28).
See page 28 for information on playing your AV compo-
nents through the HT-R510.
To get the most out of your HT-R510, you should also set
the functions on pages 25 through 27.
Press the input selector button for
the source that you want to assign:
VIDEO 2 VIDEO 3
[DVD], [VIDEO 1], [VIDEO 2],
[VIDEO 3], [TAPE], or [CD].
TUNER C D
The selected source appears on the dis-
play. (The value next to the input source is
the volume setting.)
Press the [DIGITAL INPUT] button.
The current source assignment appears, as
shown.
Use the [DIGITAL INPUT] button to
select COAX (COAXIAL), OPT1
(OPTICAL 1), OPT2 (OPTICAL 2), or
– – – – (no assignment).