Vox Level; Vox Delay; Time Out Timer - Cobra 75 All Road Owner's Manual

Main Icons
Menus
VOX Level (Level 01 - 09)
-MENU-
Intro Operation Customer
Assistance
BLUETOOTH
VOX Level sets the trigger point for VOX. The higher the level, the
VOX
louder your voice needs to be to trigger VOX. To set the VOX level:

VOX LEVEL

1. Enable VOX (see "VOX" instructions)

VOX DELAY

Customer
2. Press and hold the ENT/MENU button on the All Road
Installation
Assistance
handset to active the MENU
Secondary Icons
3. Use the DOWN arrow key to select VOX LEVEL from the
Menu Options
4. Use the ESC button to get back to the home screen
Notice Caution
VOX Delay (Level 01 - 09)
-MENU-
BLUETOOTH VOX Delay sets the transmitter ON or "hang time" after the user
VOX
stops speaking into the microphone. This setting is measured in
VOX LEVEL
seconds and can be tailored to adjust the amount of time the
VOX DELAY
transmitter hangs in between speaking. The higher the setting, the
longer the hang time. To adjust VOX DELAY:
1. Enable VOX (see "VOX" instructions)
2. Press and hold the ENT/MENU button on the All Road
handset to active the MENU
3. Use the DOWN arrow key to select VOX DELAY from the
Menu Options
4. Adjust VOX DELAY (01 - 09) using the UP or DOWN arrow
keys and select ENT (Enter) to select
5. Use the ESC button to get back to the home screen
Time Out Timer (OFF - Level 10)
-MENU-
The transmitter Time Out Timer sets the amount of time in minutes

TIME OUT TIMER

WX ALERT
that the transmitter is allowed to operate continuously. This feature
WX ALERT SCAN
helps to minimize interference to the CB channel in the event of an
WX AUTO SCAN
unintended transmission such as a 'stuck' PTT switch. Setting Time
Out Timer:
1. Press and hold the ENT/MENU button on the All Road handset
to active the MENU
2. Use the DOWN arrow to select TIME OUT TIMER from the
Menu options
3. Adjust TIME OUT TIMER (OFF - 10) using the UP or DOWN
arrows and select ENT (Enter) to select
4. Use the ESC button to get back to the home screen
12
Warranty
Warning
Main Icons
Menus
WX Alert (ON / OFF)
-MENU-
Intro Operation Customer
Assistance
TIME OUT TIMER
When WX (or Weather) Alert is enabled, it will make an alert sound
WX ALERT
when it picks up a 1050 Hz tone from the National Weather
WX ALERT SCAN
Service. The weather receiver must be set to an active weather
WX AUTO SCAN
Customer station for the 1050 Hz tone to sound. To enable/disable Weather
Installation
Assistance
Alerts:
Secondary Icons
Instructions:
1. Press the WX button on the handset to go into Weather Mode
and select an active (local) weather station
2. Press and hold the ENT/MENU button on the All Road
Notice Caution
handset to active the MENU
3. Use the DOWN arrow to select WX ALERT from the Menu
options
4. Use the UP or DOWN arrow to select ON or OFF, press ENT
to enable
5. Go back to CB Mode by pressing ESC until you get to the home
screen, then press the CB/WX button on the handset to change
between CB and Weather (WX) modes
WX Alert Scan (ON / OFF)
-MENU-
TIME OUT TIMER
WX AUTO SCAN when enabled will look for and lock on to the
WX ALERT
strongest weather station signal. This happens in the background
WX ALERT SCAN
and is useful for cross-country travel. How it works: WX AUTO
WX AUTO SCAN
SCAN locks onto a local NWS and can be accessed when you
switch over to WX mode (by press the CB/WS button on the
handset). To enable/disable Weather Alert Scanning:
1. Press and hold the ENT/MENU button on the All Road
handset to active the MENU
2. Select WX ALERT SCAN from the Menu Options
3. Use the UP or DOWN arrow to select ON or OFF, press ENT
to select
4. Press the ESC button to get back to the home scree
Warranty
Warning
13