Soundoff Signal PNFSLFLKTTH Quick Start Manual

Soundoff Signal PNFSLFLKTTH Quick Start Manual

Tahoe fog light assembly (for 2015-2020 model years)

Advertisement

TAHOE FOG LIGHT ASSEMBLY
PNFSLFLKTTH (for 2015-2020 model years)

WARNING

•HIGH CURRENT interconnects must be properly terminated. Poor crimp quality can cause heat
build-up and fire. Follow crimp connector manufacturer instructions.
•DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to vehicle
Owner's Manual for deployment zones.
•Do NOT use system to disconnect headlights, brake lights or other safety equipment.
•Unit may become hot to touch during normal operation.
•Failure to properly install connectors, fuses or wiring may cause vehicle failure or fire.
•Installation must only be performed by trained technician. Installer must determine vehicle wiring
configuration and proper integration of system.
•Use proper wire gauge. All power wires connecting to positive (+) or negative (-) battery terminal
or local chassis ground (-) must be sized to supply at least 125% of max. current and properly fused at
power source.
•Install protective grommets when routing wire through firewall or metal.
1.800.338.7337 / www.soundoffsignal.com
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at www.soundoffsignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundoffsignal.com.
FRONT FOG LIGHT ASSEMBLY
-DRIVER/ PASSENGER-
NOTICE:
Improper use or installation may void warranty coverage.
E N H A N C I N G S A F E T Y T H R O U G H I N N O VAT I O N

TECHNICAL SPECIFICATIONS

Material: Plastic molded bezel, Black finish
Dimensions
8.00"H x 11.00"W x 7.00"D
(bracket only):
Pg. 1 PNFSLFLKTTH 0120

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PNFSLFLKTTH and is the answer not in the manual?

Questions and answers

Summary of Contents for Soundoff Signal PNFSLFLKTTH

  • Page 1 Improper use or installation may void warranty coverage. To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at www.soundoffsignal.com/tech-services/returns/. If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
  • Page 2 TAHOE FOG LIGHT ASSEMBLY PNFSLFLKTTH (for 2015-2020 model years) STEP 1 REMOVE FRONT BUMPER COVER ASSEMBLY AS ONE PIECE AND NOT INDIVIDUALLY. CONSULT A LOCAL GM SERVICE CENTER FOR BEST DISASSEMBLY METHOD. -KEEP ALL HARDWARE- STEP 2 REMOVE THE 4 SCREWS THAT HOLD THE FACTORY FOG LIGHT BEZEL AND PROCEED TO STEP 3 AND 4 FOR THE ASSEMBLY PROCEDURE.
  • Page 3 TAHOE FOG LIGHT ASSEMBLY PNFSLFLKTTH (for 2015-2020 model years) STEP 3 ASSEMBLE THE NFORCE LIGHT TO BEZEL AS SHOWN BELOW. USE THE 4-40 SCREWS SUPPLIED TO ATTACH PLATE TO LIGHT HOUSING IN 4 PLACES. NFORCE LIGHT BEZEL SCREW IN THE LIGHT HOUSING WITH PLATE TO THE PLASTIC BEZEL WITH THE 2 SUPPLIED SHEETMETAL SCREWS.

Table of Contents