Sony DSC-1024HD Instructions Manual page 24

VIDEO 1 IN Composite video/reference input
S video (Y/C)
VIDEO 2 IN RGB/component/composite video
VIDEO 3 IN RGB/component
AUDIO IN 1,2, 3 (L/R) RCA pin jack, more than 10 kilohms
VIDEO OUT Composite video
S video (Y/C)
RGB / component
RCA pin jack
AUDIO OUT (L/R)
Audio gain: ± 1.0 dB typical
Total harmonic distortion: less than
48
BNC connector x 2 (loop-through),
75 ohms (automatic termination)
NTSC3.58/PAL4.43,1 Vp-p typical
Black burst signal for the gen-lock
function*
4-pin mini DIN connector x 2 (loop-
through), 75 ohms (automatic
termination)
Y: 1 Vp-p typical, sync negative
C: 0.286 Vp-p (NTSQ/0.3 Vp-p
(PAL) typical
D-sub 15-pin, 3-row x 2 (loop-
through), 75 ohms/high
impedance
R/G/B: 0.714 Vp-p
H/V or composite sync: 1 to 5 Vp-p
Y/B-Y/R-Y: 0.7 Vp-p (NTSC/PAL,
sync on Y)
Composite video: 1 Vp-p
(NTSC3.58/PAL4.43)
D-sub 15-pin, 3-row connector x 2
(loop-through), 75 ohms/high
impedance
R/G/B: 0.714 Vp-p (sync on G
acceptable)
H/V or composite sync: 1 to 5 Vp-p
Y/B-Y/R-Y: 0.7 Vp-p typical
(NTSC/PAL.svnconY)
0 dBs (1 Vrms) max.
BNC connector, 75 ohms typical
NTSC3.58/PAL4.43,1 Vp-p typical
4-pin mini DIN connector, 75 ohms
typical
Y: 1 Vp-p typical, sync negative
C: 0.286 Vp-p (NTSC)/0.3 Vp-p
(PAL) typical
D-sub 15-pin, 3-row connector, 75
ohms typical
R/G/B: 0.714 Vp-p with external
sync
H/V or composite sync: TTL sync
negative
Y/B-Y/R-Y: 0.7 Vp-p typical (sync
onY)
1 %, 1 Vrms
Horizontal rate: 15.6 to 70 kHz,
Capture range
Vertical rate: 50 to 120 Hz
Preset signal Input: 10 formats
Output: 7 formats
Gen-lock output: NTSC or PAL
(See page 49.)
Video memory 1,152 x 1,152 x 24 bits (RGB total)
Sampling rate 14.3 to 40 MHz offset phase max.
(equivalent to 80 MHz sampling)
14.3 to 50 MHz max.
Output pixel clock
Power requirements 100 to 120 V AC, 50/60 Hz, 0.4 A
200 to 240 V AC, 50 - 60 Hz, 0.25 A
Power consumption 30 W (max. in operation)
3 W (power off)
Operation temperature Oto35°C(32-95°F)
424 x 44 x 354 mm (w/h/d)
Dimensions
(16 V4 x 1 V4 x 14 inches)
excluding bracket and legs
Approx. 4.1 kg (9 Ib 1 oz)
Mass
AC power cord (1)
Supplied accessories
Signal cable (1)
Screws for mounting bracket kit MB-
510 (4)
Rack mount bracket MB-510
SMF-400: D-sub 15-pin (male) to 5 BNC cable
SMF-401: D-sub 15-pin (male) to D-sub 15-pin (male) cable
Remote commander RM-854, RM-1271, RM-PJ1292, RM-PJ350
* Note on the gen-lock function
The reference signal should comply with SMPTE 170M (NTSC)
or ITU-R624 (PAL).