PaloAlto Networks TECHDOCS ION 1200 Quick Start Manual

ION 1200
1
Before You Begin
Use this document to install and set up your ION 1200. Refer to the ION 1200 Hardware Reference
at https://docs.paloaltonetworks.com/hardware/ion-1200-hardware-reference
information, specifications, and more detailed procedures for installing the device.
•
Verify that the installation site has adequate air circulation and AC power.
•
Have a #1 Phillips-head screwdriver available.
•
Unpack the equipment and verify that you received the following items:
Items
ION 1200
Power Adapter, 25W
Power Cord, AC
Cable Assy, Blue, USB 2.0 AM to 8P8C RJ45, 1830mm L, 28 AWG
Shielded RJ-45 CAT6 Ethernet cable
Wood screws (.75") to mount the device and power adapter bracket to wood studs or
plywood.
Drywall anchors and screws (1.25") to mount the device and power adapter bracket to a
drywall or similar material that cannot securely accommodate wood screws.
Power adapter wall-mount kit (includes one each of the following: a power adapter
bracket, a Velcro strap, and a plastic cable tie).
Sheet, Limited Warranty
2
Install the Device
You can install the ION 1200 on a flat surface, in a rack, or
on a wall.
Ensure there are no building services (water, gas, or
wiring) behind the wall where you intend to install the
device.
Install the device on a wall
Download the Wall Mount template from
1
paloaltonetworks.com/hardware/ion-1200-hardware-
reference/install-ion-1200/wall-mount-template.
Temporarily secure the Wall Mount template (Figure 1)
2
to the wall where you intend to mount the device and
use it to mark the location for each of the four wall-
mount screws. Use a pointed object to punch through
the paper and visibly mark the wall; then remove the
template and verify measurements.
Use a type 1 Philips head screwdriver to install the
3
appropriate screws into each of the four marked
locations:
docs.paloaltonetworks.com
for safety
Quantity
1
1
1
1
1
6
6
1
1
https://docs.
Figure 1 - Wall mount template
Drywall—First press a drywall anchor slightly into the center of a template mark. Then use
◼
the screwdriver to apply pressure while turning the anchor clockwise until the surface of the
anchor is flush with the wall. After the drywall anchor is secure, install a 1.25" anchor screw
into the anchor until the bottom of the screw head protrudes ¼" from the wall. Repeat this
step for the other three screw locations.
Plywood wall—Use the screwdriver to insert a .75" wood screw into the center of each
◼
template mark that is located over wood until the bottom of the screw heads protrude ¼"
from the wall. If any screw location is located over wood, use a .75" wood screw instead of a
drywall anchor and screw.
Align the four holes on the bottom of the device with the four screws on the wall and hang the
3
device on the screws.
Install the power adapter in the power adapter wall-mount bracket using the Velcro strap and
4
cable tie (Figure 2). Make sure to align the cable tie with the notches in the bracket to prevent
the power cord from falling out.
Mount the power adapter wall-mount bracket next to the device using wood or drywall screws
5
as appropriate.
Install the device in a rack
When installing the device in a rack, ensure there is nothing placed above the device.
Refer to the ION 1200 Hardware Reference at
ion-1200-hardware-reference
Page 1 of 2
Quick Start Guide
Figure 2 - Power adapter in the wall mount bracket
https://docs.paloaltonetworks.com/hardware/
to learn to install the device in a rack.