Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for unicraft WPP 10 TE
Summary of Contents for unicraft WPP 10 TE
- Page 1 Operating Instructions Hydraulic workshop press WPP 10 TE WPP 10 TE...
-
Page 2: Table Of Contents
Forwarding and reproduction of this document as well as use and notification of its content is not permitted without explicit consent. Infringements shall oblige to payment of compensation. Subject to technical modifications and changes. WPP 10 TE | Version 2.05... -
Page 3: Introduction
All data in these operating instructions has been com- You have made an excellent choice in purchasing the piled on the basis of the state-of-the-art, valid standards WPP 10 TE Unicraft hydraulic workshop press. and guidelines as well as our many years of expertise and experience. -
Page 4: Operator Responsibility
WPP 10 TE | Version 2.05... -
Page 5: Personal Protective Equipment
Any claims resulting from damage due to unintended use Protective clothing shall be excluded. Protective clothing is tight-fitting work clothing without protruding parts, usually with a low tear resistance. WPP 10 TE | Version 2.05... -
Page 6: Technical Data
Compression force 10 t Foot width x depth 570 x 495 mm Total height 1058 mm Fig. 3: Type plate of the WPP 10 TE hydraulic workshop press Frame height 732 mm Inside width 340 mm 4.4 Pressure gauge Work area... - Page 7 Any loose parts must be securely fastened to the hydraulic workshop press, secured separately or safely stored in a separate container. Blank metal parts have been greased to protect them from humidity and dirt. WPP 10 TE | Version 2.05...
-
Page 8: Machine Description
Make sure there is a sufficient amount of clearance, ap- proximately 1 m clearance on each side (see Fig. 6) and the work area is adequately lit. Fig. 5: WPP 10 TE hydraulic workshop press Fig. 6: Correctly set up the hydraulic workshop press 1 Pressure gauge... -
Page 9: Commissioning
- Do not reach into the press and keep away from moving parts! Wear protective goggles! Wear safety shoes! Fig. 7: Parts for assembly of the WPP 10 TE hydraulic workshop press Wear protective clothing! NOTE ! Carry out the following before operating the hydrau- lic workshop press for the first time. -
Page 10: Adjusting The Table Height
Step 1: move the rotary button of the switching valve to the left-hand position. The hydraulic oil automatically returns from the cylinder IMPORTANT! back into the pump oil tank. Make sure the workpiece has been centred under the piston! WPP 10 TE | Version 2.05... -
Page 11: Processing The Workpiece
The hydraulic pipes must be replaced after an operating period of six years. In the event of increased usage peri- ods and stricter requirements pipes must be replaced every two years. WPP 10 TE | Version 2.05... - Page 12 Machine component Lubrication point Lubrication medium Manual hydraulic pump Stamp Grease: Shaft on the switching valve Apply grease to the listed components using a greased brush. Remove excess lubricant using a dry and lint-free cloth. WPP 10 TE | Version 2.05...
-
Page 13: Disposal, Reusing Used Machines
The pressure gauge for the Hydraulic workshop press 11.2 Disposing of lubricants WPP 10 TE must be ordered. The pressure gauge has the number 1 in the spare parts drawing 1. Lubricant manufacturers provide disposal information for By ordering spare parts, send a copy of the spare parts the lubricants used. -
Page 14: Spare Parts Drawings
The following drawing are intended to identify the required spare parts in the event of service. If applicable, submit a copy of the parts drawing including the highlighted components to your authorised retailer. Fig. 8: WPP 10 TE spare parts drawing WPP 10 TE | Version 2.05... -
Page 15: Hydraulics Circuit Diagram
Hydraulics circuit diagram 13 Hydraulics circuit diagram Fig. 9: WPP 10 TE hydraulics circuit diagram WPP 10 TE | Version 2.05... -
Page 16: Maintenance Plan
Maintenance plan 14 Maintenance plan Maintenance plan WPP 10 TE daily week 200 h 200 h 300 h on de- yearly mand years Date Opera- Staff Signa- ting ture hours WPP 10 TE | Version 2.05... -
Page 17: Ec Declaration Of Conformity
Risk assessment and reduction of risks DIN EN 693:2009 Tooling machines - safety - hydraulic presses Responsible for documentation: Kilian Stürmer, Stürmer Maschinen GmbH, Dr.-Robert-Pfleger-Str. 26, D-96103 Hallstadt Hallstadt, on 15 January 2014 ______________________ Kilian Stürmer Chief executive WPP 10 TE | Version 2.05... - Page 18 www.unicraft.de...
Need help?
Do you have a question about the WPP 10 TE and is the answer not in the manual?
Questions and answers