Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for unicraft WPP 15 E
Summary of Contents for unicraft WPP 15 E
- Page 1 Operating instructions Hydraulic workshop press WPP 15 E WPP 15 E...
-
Page 2: Table Of Contents
Forwarding and reproduction of this document as well 15 EU Declaration of Conformity ......21 as use and notification of its content is not permitted without explicit consent. Infringements shall oblige to payment of compensation. Subject to technical modifications and changes. WPP 15 E | Version 1.02... -
Page 3: Introduction
Please submit any information and experiences you cates a directly dangerous situation which may make during application of the machine as these may cause death or serious injury if not averted. be valuable for product improvements. WPP 15 E | Version 1.02... -
Page 4: Operator Responsibility
WPP 15 E | Version 1.02... -
Page 5: Operating Staff Qualification
Staff must wear the personal protective equipment indicated in individual sections of these operating instructions when carrying out the different tasks on the machine. WPP 15 E | Version 1.02... -
Page 6: Intended Use
3.2 Remaining risks Even when observing all safety instructions, operation of the workshop press involves the remaining risks de- scribed in the following. WPP 15 E | Version 1.02... -
Page 7: Type Plate
Blank metal parts have been greased to protect them Fig. 2: Type plate of the WPP 15 E hydraulic workshop press from humidity and dirt. 4.4 Pressure gauge... -
Page 8: Machine Description
Make sure there is a sufficient amount of clearance, ap- proximately 1 m clearance on each side (see Fig. 6) and the work area is adequately lit. Fig. 4: WPP 15 E hydraulic workshop press 1 Hydraulic cylinder Fig. 5: Correctly set up the hydraulic workshop press... -
Page 9: Installing The Crossbeam Feet And Press Table
Step 2: insert the support bolts into the frame at the de- sired height and secure them using the safety splints. The position the press table onto the support bolts in the frame. Fig. 8: Installing the pressure gauge WPP 15 E | Version 1.02... -
Page 10: Before Commissioning
Wear protective goggles! 10.2 Setting up the work area The work area must have been set up properly to be Wear protective gloves! able to safely process the workpiece. WPP 15 E | Version 1.02... -
Page 11: Adjusting The Horizontal Working Position
For this reason, the adjusting screw has been covered. The pump pressure can also be built up using the pneumatic foot-operated pump. WPP 15 E | Version 1.02... -
Page 12: Processing The Workpiece
The hydraulic pipes must be replaced after an operating period of six years. In the event of increased usage peri- ods and stricter requirements pipes must be replaced every two years. WPP 15 E | Version 1.02... - Page 13 Machine component Lubrication point Lubrication medium Manual hydraulic Stamp Grease: pump Shaft on the switching valve Apply grease to the listed components using a greased brush. Remove excess lubricant using a dry and lint-free cloth. WPP 15 E | Version 1.02...
-
Page 14: Disposal, Reusing Used Machines
(6) Any repairs carried out by ordering parties/purchasers or specific data sheets. third parties without our consent or incorrect repairs by a ser- vice partner that has not been authorised by the manufacturer shall render any claims for liability for defects void. WPP 15 E | Version 1.02... -
Page 15: Spare Parts
Example 14 Spare parts You are required to order the pressure gauge for the WPP 15 E workshop press. The pressure gauge is de- DANGER! fined as number 38 in spare parts drawing 1. Risk of injury caused by the use of... -
Page 16: Spare Parts Drawings
The following drawings are intended to identify the required spare parts in the event of service. If applicable, submit a copy of the parts drawing including the highlighted components to your authorised retailer. Fig. 10: Spare parts drawing 1 WPP 15 E | Version 1.02... - Page 17 Spare parts Fig. 11: Spare parts drawing 2 WPP 15 E | Version 1.02...
-
Page 18: Hydraulics Circuit Diagram
Spare parts 14.3 Hydraulics circuit diagram Fig. 12: WPP 15 E hydraulics circuit diagram WPP 15 E | Version 1.02... -
Page 19: Eu Declaration Of Conformity
Tooling machines - safety - hydraulic presses DIN EN 1494:2009-05 Mobile or movable hoisting devices and related equipment Technology department, Dr.-Robert-Pfleger-Str. 26, D-96103 Hallstadt Responsible for documentation: Hallstadt, 30.04.2015 ______________________ Kilian Stürmer General Manager WPP 15 E | Version 1.02... - Page 20 www.unicraft.de...
Need help?
Do you have a question about the WPP 15 E and is the answer not in the manual?
Questions and answers