Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for unicraft WPP 15 TE
Summary of Contents for unicraft WPP 15 TE
- Page 1 Operating Instructions Hydraulic workshop press WPP 15 TE WPP 15 TE...
-
Page 2: Table Of Contents
13.3 Hydraulic Circuit diagram........ 17 explicit consent. Infringements shall oblige to payment of 14 EC Declaration of Conformity ......18 compensation. 15 Maintenance plan ..........19 Subject to technical modifications and changes. WPP 15 TE | Version 1.06... -
Page 3: Introduction
This combination of symbol and signal term indi- make during application of the machine as these may be cates potentially hazardous situations which may valuable for product improvements. cause death or serious injury if not averted. WPP 15 TE | Version 1.06... -
Page 4: Operator Responsibility
- Operators shall regularly check that the safety and bear the legal product responsibility in terms of the equipment is fully functional and complete. protection of users, staff or third parties during operation. WPP 15 TE | Version 1.06... -
Page 5: Operating Staff Qualification
Personal protective equipment is intended to protect the health and safety of persons at work. Staff must wear the personal protective equipment indicated in individual sections of these operating instructions when carrying out the different tasks on the machine. WPP 15 TE | Version 1.06... -
Page 6: Intended Use
The WPP 15 TE hydraulic workshop press is exclusively dents or damage: intended for use in crafts and for repairs. It is suitable for... -
Page 7: Type Plate
"Technical data" of the machine. When the machine is unpacked, the weight Fig. 2: Type plate of the WPP 15 TE hydraulic workshop press of the machine can also be read on the rating plate. -
Page 8: Machine Description
Packaging materials made of cardboard must be shred- ded and disposed of as part of waste paper recycling. Fig. 4: WPP 15 TE hydraulic workshop press 1 Hydraulic cylinder The foils are made of polyethylene (PE), padding is made of polystyrene (PS). -
Page 9: Setup
These parts must be assembled or converted and se- cured with screws. Step 1: screw the pump unit onto the outside of the frame using the screws and shims (see Fig. 6). Step 2: install the pressure lines. WPP 15 TE | Version 1.06... -
Page 10: Installing The Pressure Gauge
Then once again close the valves. Wear safety shoes! Step 3: Check all lines and connections are not leaking. Check all machine parts are undamaged and op- erate as intended. Wear protective clothing! WPP 15 TE | Version 1.06... -
Page 11: Adjusting The Table Height
Step 4: Continue to pump until the required pump pres- sure has built up. For this purpose, monitor the pressure gauge. IMPORTANT! - Do not exceed the press capacity! - Do not use extensions for the pressure lever WPP 15 TE | Version 1.06... -
Page 12: Retracting Piston
The piston returns to its base position/standby posi- tion. Step 9: Remove the workpiece. Fig. 8: Mounting the mandrel set Step 1: Unscrew the piston head using the attached hex key. WPP 15 TE | Version 1.06... -
Page 13: Maintenance And Repairs
The hydraulic pipes must be replaced after an operating period of six years. In the event of increased usage peri- ods and stricter requirements pipes must be replaced every two years. WPP 15 TE | Version 1.06... - Page 14 Machine component Lubrication point Lubrication medium Manual hydraulic pump Stamp Grease: Apply grease to the listed components using a greased Shaft on the switching valve brush. Remove excess lubricant using a dry and lint-free cloth. WPP 15 TE | Version 1.06...
-
Page 15: Disposal, Reusing Used Machines
Example Lubricant manufacturers provide disposal information for The pressure gauge for the Workshop press WPP 15 TE the lubricants used. If necessary, request product-spe- must be ordered. The pressure gauge has the number cific data sheets. -
Page 16: Spare Parts Drawing
The following drawing is intended to identify the required spare parts in the event of service. If applicable, submit a copy of the parts drawing including the highlighted components to your authorised retailer. Fig. 9: Spare parts drawing WPP 15 TE | Version 1.06... -
Page 17: Hydraulic Circuit Diagram
EC Declaration of Conformity 13.3 Hydraulic Circuit diagram Fig. 10: Hydraulic circuit diagram of the WPP 15 TE WPP 15 TE | Version 1.06... -
Page 18: Ec Declaration Of Conformity
Risk assessment and minimising risks DIN EN 1494:2009-05 Mobile or movable hoisting devices and related equipment Responsible for documentation: Kilian Stürmer, Stürmer Maschinen GmbH Dr.-Robert-Pfleger-Str. 26, D-96103 Hallstadt Hallstadt, 19th of April 2016 ______________________ Kilian Stürmer General Manager WPP 15 TE | Version 1.06... -
Page 19: Maintenance Plan
Maintenance plan 15 Maintenance plan Maintenance schedule WPP 15TE 200 h 200 h 300 h Date Opera- Staff Signa- ting ture hours WPP 15 TE | Version 1.06... - Page 20 www.unicraft.de...
Need help?
Do you have a question about the WPP 15 TE and is the answer not in the manual?
Questions and answers