Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for unicraft SSK Series
Summary of Contents for unicraft SSK Series
- Page 1 Operating Instructions Sandblasting Cabinet SSK 1 SSK 1.5 SSK 1 SSK 1.5...
-
Page 2: Table Of Contents
6.1 Delivery............... 8 7 Assembly and connecting........8 Fax: 0049 (0) 951 96555 - 55 7.1 Assembly ............8 E-Mail: info@unicraft.de 7.2 Electrical connection........... 9 Internet: www.unicraft.de 7.3 Compressed air connection ........ 9 7.4 Air regulation SSK 1.5 ........9 8 Commissioning .............10 9 Care, maintenance and repair ......11... -
Page 3: Introduction
The safety notes are introduced by si- Repair service: gnal words which express the concern of the risk. Fax: 0049 (0) 951 96555-111 E-Mail: service@stuermer-maschinen.de Internet: www.unicraft.de Spare parts orders: DANGER! Fax: 0049 (0) 951 96555-119 E-Mail: ersatzteile@stuermer-maschinen.de This combination of symbol and signal words indi-... -
Page 4: Obligations Of The Operating Company
Safety - During the entire lifetime of the sandblasting cabi- net, the operating company must verify whether WARNING! the operating manuals prepared by her correspond This combination of symbol and signal words indi- to the current status of the regulations, and must cates a possibly dangerous situation which may lead adapt these if necessary. -
Page 5: Personal Protective Equipment
Safety Operator: Respiratory protection The operator is instructed by the operating company about the assigned tasks and possible risks in case of The respiratory protection protects the respiratory improper behaviour. Any tasks which need to be per- tract against the ingress of dust and small foreign formed beyond the operation in the standard mode must bodies. -
Page 6: Intended Use
Intended use The following safety labels and symbols are appropriate: Technical data SSK 1 Model SSK 1 Volume work cabin 90 liter Working pressure 2,8 - 5,5 bar Inlet pressure max. 8,6 bar Blasting media Grit size 0,2-0,3 mm (recommended) Blasting media Grain 0,125-0,45 mm size (maximum) -
Page 7: Type Plate
Transport, packaging, storage Before starting the transport check the transport route for 4.1 Type plate possible danger points, unevenness and disturbances as well as for sufficient strength and load capacity. Danger points, unevenness and disturbance points must be inspected before transport. The removal of danger spots, disturbances and unevenness at the time of trans- port by other employees leads to considerable dangers. -
Page 8: Delivery
Assembly and connecting Use protective clothes! CAUTION! crushing! Injuries to hands and fingers may result from improper use of the sandblasting cabin. - Pay attention to stable supports and support de- vices. 7.1 Assembly The sandblasting cabinet is already pre-assembled. Fig. -
Page 9: Electrical Connection
Assembly and connecting Step 5: The Pedal aconnect to the housing of the SSK 1.5. Make sure that the correct cables (Fig.7) are connected to each other. Fig. 9: ground connection Fig. 7: Mount the pedal control Step 3: Connect the power cord to the mains. 7.3 Compressed air connection To operate the sand blasting cabin you need a compres- sor with at least 350 liters / min (SSK1) and 196 liters /... -
Page 10: Commissioning
Commissioning respiratory protection! Use safety shoes! Use protective clothing! Fig. 11: Setting working pressure NOTE! Before using the sand blasting cabin for the first time, NOTE! carry out the following points. - Check all screw connections on the installed sand- If the pressure drops by several bar, the air supply is blast cabinets and tighten them if necessary. -
Page 11: Care, Maintenance And Repair
Care, maintenance and repair Step 5: Place the workpiece to be machined in the If the sandblasting cabin does not work properly, contact sandblast booth and switch on the lighting of a dealer or our customer service. The contact details can the sandblast cabin. -
Page 12: Troubleshooting
Troubleshooting 10 Troubleshooting ATTENTION! If any of the following errors occur, immediately stop working with the sandblasting gun. It can cause serious injury or damage to the tool. All repairs or replacement work must only be carried out by quali- fied and trained personnel. -
Page 13: Spare Parts
Spare parts Example 12 Spare parts The gloves for the Sandblasting cabinet SSK 1 must be ordered. The gloves has the number 21 in the spare DANGER! parts drawing 1. Risk of injury through use By ordering spare parts, send a copy of the spare parts wrong spare parts! drawing (1) with the marked part (gloves) and marked The use of incorrect or faulty replacement parts can... -
Page 14: Spare Parts Drawings
Spare parts 12.1 Spare parts drawings The following drawings should help in case of service to identify necessary spare parts. To order, send a copy of the parts drawing with the parts marked to the authorized dealer. 12.1.1Spare parts drawing SSK 1 Fig. - Page 15 Spare parts 12.1.2 Spare parts drawing SSK 1.5 Fig. 14: Spare parts drawing SSK 1.5 SSK-Series | Version 1.08...
-
Page 16: Ec Declaration Of Conformity
According to machine directive 2006/42/EG Annex. II 1.A Manufacturer/distributing company: Stürmer Maschinen GmbH Dr.-Robert-Pfleger-Str. 26 D-96103 Hallstadt hereby declares that the following product Product group: Unicraft® Werkstatttechnik Machine type: Sandblasting cabinet Designation of the machine *: SSK 1 Item number *: 6204000 SSK 1.5... -
Page 17: Attachment
Attachment 14 Attachment Information zu den mitgelieferten Handschuhen/ Information about the supplied gloves Schutzhandschuhe 1 Paar Artikelnummer Protection gloves 1 Pair Item number HS-SSK1 6204100 Hersteller: YONGKANG XIEHENG ZHEJIANG PROVINCE INDUSTRY & COMMERCE CO., LTD. Manufacturer: NO. 9 XISHAN WEST ROAD, ECONOMIC DEVELOPMENT ZONE, 321300 YONGKANG ZHEJIANG, CHINA Artikel: SBC Gloves –... - Page 18 Attachment Information zu den mitgelieferten Handschuhen / Information about the supplied gloves SSK 1.5 Schutzhandschuhe 1 Paar Artikelnummer Protection gloves 1 Pair Item number HS-SSK1.5 6204160 Hersteller: YONGKANG XIEHENG ZHEJIANG PROVINCE INDUSTRY & COMMERCE CO., LTD. Manufacturer: NO. 9 XISHAN WEST ROAD, ECONOMIC DEVELOPMENT ZONE, 321300 YONGKANG ZHEJIANG, CHINA Artikel: SBC Gloves-3 –...
-
Page 19: Notes
Notes 15 Notes SSK-Series | Version 1.08... - Page 20 www.unicraft.de...
Need help?
Do you have a question about the SSK Series and is the answer not in the manual?
Questions and answers