Table of Contents
Advertisement
Available languages
Available languages
Quick Links
ASSEMBLY AND INSTALLATION
T0692 / T0693
WARNING:
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
Hardware Package (included):
Mounting Screw X2
Mounting Screw X2
#8/32X1/2 in
#6/32 X1/2 in
Tools Needed:
(1) Phillips-head Screwdriver
Important to Know:
1. If you are not familiar with state and local electrical
codes, it is recommended that you consult with a
qualified electrician.
2. This fixture requires a 120 VAC, 60 Hz power
source.
3. For general safety and to avoid any possible
damage to the sensor, be sure the power is
switched "off" before adjustment.
Maximum Wattage: 2-150 W (bulb not included)
Working Temperature Range: -
Note: Fixture can be wall mounted or eave mounted.
Wall Mounted
Read notes section on page 4 for additional information about mounting location of fixture.
Light fixture and sensor should be mounted as shown above when installed (depending upon type of installation)
Before installing the light fixture under an eave, the sensor head must be rotated as shown in the next two steps for
proper operation and to avoid the risk of electrical shock.
For eave mounted only:
Rotate the sensor head towards the back plate.
Backplate
INSTRUCTIONS
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Mounting Screw X2
Mounting Strap
#10/24 X1/4 in
(2) 1/8" Flat-head Screwdriver
13°F ~ 113°F
Controls
Page 1 / 5
Decorative cover
Fixture Mounting Screw
1. Phillips-head screwdriver for attaching mounting screws to
mounting strap, mounting bracket and fixture to mounting bracket.
2. 1/8" wide flat-head screwdriver for connecting the source wires
into the wiring terminal station on the mounting bracket.
Features:
1. Motion sensor: turns light ON automatically when
motion is detected and turns light OFF or remains
in low-level brightness when motion stops.
2. Photocell keeps the light OFF during daylight hours.
Eave Mounted
Rotate the sensor head clockwise 180˚ so the controls face down.
Controls
Wire Connector
Gasket
Controls
221031
Advertisement
Table of Contents
Related Manuals for Vaxcel Dualux T0692
Summary of Contents for Vaxcel Dualux T0692
- Page 1 ASSEMBLY AND INSTALLATION INSTRUCTIONS T0692 / T0693 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS. Hardware Package (included): Mounting Screw X2 Mounting Screw X2...
-
Page 2: Installation Steps
Decorative Cover FRONT Outlet Box PAR 38 Bulb Max.150W (not included) Mounting Strap Sensor Wire Connector Backplate Installation Steps Turn off the power at fuse or circuit box. 1. Install the mounting strap to the outlet box with the stamped word “FRONT” facing away from the outlet box, using two mounting screws that best fit the outlet box. -
Page 3: Functions And Operations
Fig. 2 Fig. 3 Sensor Adjustment Lower For Short Coverage Sensitivity of Motion Sensor ● You can adjust the sensitivity of the motion sensor by using the “SENS” knob located on the right side of the bottom surface of the sensor. (See Fig. 4) ●... - Page 4 Functions and Operations (continued) 4. PC MODE (nighttime operation only) ● In "PC" mode, the light will turn on at full brightness at dusk and remains on until dawn. 5. 3 HOURS (3H) MODE (nighttime operation only) ● In “3H” mode, the light turns to high-level brightness at dusk, and stays on for 3 hours, then it turns to low-level 30% brightness.
-
Page 5: Troubleshooting
The following parts are available for re-order if damaged or missing. Mounting Screw X2 Mounting Screw X2 Mounting Screw X2 Wire Connector Gasket Mounting Strap Decorative cover Fixture Mounting Screw #8/32X1/2 in #6/32 X1/2 in #10/24 X1/4 in Assembly Kit 6605MM (1 SET) FOR T0692 6606MM (1 SET) FOR T0693 Troubleshooting... -
Page 6: Herramientas Necesarias
INSTRUCCIONES DE ENSAMBLAJE E INSTALACIÓN T0692 / T0693 ADVERTENCIA: PARA EVITAR EL RIESGO DE CHOQUE ELÉCTRICO, ASEGÚRESE DE APAGAR LA ENERGÍA ANTES DE INSTALAR O HACER EL MANTENIMIENTO DE ESTE ARTEFACTO. NOTAS: 1. Antes de instalar, consulte los códigos de electricidad locales para ver los requisitos de cableado y conexión a tierra. - Page 7 Cubierta decorativa FRONT Caja de toma de corriente Bombilla PAR 38 150 W máx. (no se incluye) Placa de montaje Sensor Conector de cable Placa posterior Pasos de la instalación Apague la corriente en la caja de fusibles o de circuitos. 1.
-
Page 8: Funciones Y Operaciones
Fig. 2 Fig. 3 Ajuste más bajo del sensor para cobertura corta Sensibilidad del sensor de movimiento ● Puede ajustar la sensibilidad del sensor de movimiento usando el selector de "SENSIBILIDAD" ubicado a la derecha en la superficie inferior del sensor. (Vea la Fig. 4) ●... - Page 9 Funciones y operaciones (continuación) 4. MODO PC (solo funcionamiento nocturno) ● En el modo "PC", la luz se encenderá al brillo máximo al anochecer y permanecerá encendida hasta el amanecer. 5. MODO de 3 HORAS (3H) (solo funcionamiento nocturno) ● En el modo de "3H", la luz pasa al brillo de nivel alto al anochecer y permanece encendida durante 3 horas, luego pasa al brillo de nivel bajo.
-
Page 10: Resolución De Problemas
Las siguientes piezas están disponibles para pedido si están dañadas o faltan. Tornillo de montaje X2 Tornillo de montaje X2 Tornillo de montaje X2 Tornillo de montaje Conector de cable Empaquetadura Placa de montaje Cubierta decorativa 8/32X1/2 in 6/32 X1/2 in 10/24 X1/4 in del artefacto Kit de ensamblaje...