Advertisement
Quick Links
ASSEMBLY AND INSTALLATION
T0620 / T0621
VX21111W / VX21111BZ
WARNING:
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
Hardware Package (included):
Mounting Screw X2
Mounting Screw X2
#8/32X1/2 in
#6/32 X1/2 in
Important to Know:
1. If you are not familiar with state and local electrical
codes, it is recommended that you consult with a
qualified electrician.
2. This fixture requires a 120 VAC, 60 Hz power
source.
3. For general safety and to avoid any possible
damage to the sensor, be sure the power is
switched "off" before adjustment.
Maximum Wattage: 35 W
Working Temperature Range:
Note: Fixture can be wall mounted or eave mounted.
Wall Mounted
Read notes section on page.4 for additional information about mounting location of fixture.
Light fixture and sensor should be mounted as shown above when installed (depending upon type of installation)
Before installing the light fixture under an eave, the sensor head must be rotated as shown in the next two steps for
proper operation and to avoid the risk of electrical shock.
For eave mounted only:
Swing the sensor head towards the mounting bracket.
Backplate
INSTRUCTIONS
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Mounting Screw X2
#10/24 X1/4 in
--13°F ~ 113°F
Controls
Page 1 / 17
Mounting Strap
Decorative cover
Features:
1. Energy saving LED fixture.
2. Motion sensor: turns light ON automatically when
motion is detected and turns light OFF automatically
when motion stops.
3. Photocell keeps the light OFF during daylight hours.
4. When in manual override mode, use wall switch
to change the function and perform the function
conversion.
Eave Mounted
Fixture Mounting Screw
Controls
Controls
211231
Advertisement
Related Manuals for Vaxcel T0620
Summary of Contents for Vaxcel T0620
- Page 1 ASSEMBLY AND INSTALLATION INSTRUCTIONS T0620 / T0621 VX21111W / VX21111BZ WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
-
Page 2: Installation Steps
Backplate Light Fixture FRONT Decorative cover Outlet Box Mounting Strap Sensor Installation Steps Turn off the power at fuse or circuit box. 1. The fixture mounting bracket is pre-assembled on the light fixture. Unscrew both the decorative cover and the fixture mounting screw in order to remove the mounting bracket. - Page 3 Fig. 3 Fig. 2 Sensor Adjustment Lower For Short Coverage Fig. 4 Adjusting the Light Head: 1. Gently grasp the light heads and tilt them up or down, left or right to away from the sensor.(See Fig. 4) electrical shock. Sensitivity of Motion Sensor: 1.
-
Page 4: Customization Options
INSTRUCTIONS (continue FUNCTION AND OPERATION (continued) INSTRUCTIONS (continue 3 HOURS (3H) MODE (nighttime operation only) pre-selected low-level brightness (2700K). It turns to high-level brightness (5000K) when motion is detected, and stays on as long as motion continues. When motion is no longer detected, it remains on for the predetermined shut-off delay time you set (30s/1min/3min), then returns to the pre-selected low-level brightness (2700K) automatically. - Page 5 USER GUIDE Se ng for single light through mobile device (Take iOS for example as below. Android will be slightly di erent). Before you start 1. Search "DualuxBT" in IOS APP 2. Start the App and click store or "Dualux" in Android “WIFI”.
- Page 6 USER GUIDE (continued) 7. Follow the step 1, 2, 3 show 8. Choose a 2.4GHz WiFi in the phone, then click “next”. network and enter the WiFi password, then click 9:41 AM 100% 9:41 AM 100% “Confirm”. Back Back Note: Only works with 2.4GHz WiFi networks.
- Page 7 USER GUIDE (continued) 9.4 Choose a “HF-XXXXXX” WiFi to connect. (See Fig 9.4-1) then click “ ” to return. (See Fig 9.4-2) 9.5 The status window will appear once the device(s) have successfully connected 9:41 AM 100% 9:41 AM 100% and the 3 bullets point on the Back Back...
- Page 8 USER GUIDE (continued) 13. Click the “Functions”, You 14. Select “Auto” in Manual can choose “Test”, “Auto”, override and adjust “Motion or “Custom Setting”. Delay Time”, “Detection Distance” , “Brightness” and Select “Test” in Manual “CCT change” as desired. override and adjust Then click “Save”.
- Page 9 USER GUIDE (continued) 17. It will turn to “change image”. 18. Go back to “Light list”, the The photo will show on it. photo will show on the (Android will be slightly different left of “Light 1”. from the iOS system) 19.
- Page 10 USER GUIDE (continued) Voice Command Control Manual Override Daytime: During day time, when you say “Turn On Security light”, the light will turn on and stay on all day, and then go into Auto Mode during dusk. Manual Override Nighttime: During nighttime, when you say “Turn On Security light”, the light will turn on and stay on.
- Page 11 USER GUIDE (continued) Smarter More Helpful Home Security Light That Work with Alexa Control lighting with simple voice commands. Adjust brightness: Alexa, turn on/off security light; Alexa, make security light to 10% ~ 100% percent; Alexa, brighten/increase security light; Alexa, dim/decrease security light. Adjust color temperature: Alexa, make security light warmer;...
- Page 12 USER GUIDE (continued) 6. Click “ENABLE TO USE”. 5. In the search menu type “Innovation & Perfect”. then click “Innovation & Perfect”. 7. Enter the same user name 8. Once successful linked & password that you have page appear, click upper registered under the dualux left "X ".
- Page 13 USER GUIDE (continued) 11. When light is discovered 12. Add your light to a group. click "set up device". 13. Select a group. 14. Light is added to a group. Security Light added to Living Room 15. Click "lights". 16. New device is displayed in group.
- Page 14 USER GUIDE (continued) Smarter More Helpful Home Security Light That Work with Google Home Control lighting with simple voice commands. Adjust brightness: Hi, Google, turn on/off security light; Hi, Google, make security light to 10% ~ 100% percent; Hi, Google, brighten/increase security light; Hi, Google, dim/decrease security light.
- Page 15 USER GUIDE (continued) 5. Enter the same user name 6. Wait for signing in. & password that you have registered under the dualux App. 7. Go back to main page. 8. A device links to google home automatically. Security Light Up to 70ft.
-
Page 16: Troubleshooting
Troubleshooting ---The light does not come on at all: 1. Make sure the wall switch and circuit breaker are on. 2. Make sure the wiring is correct. 3. Cover the sensor with dark color cloth to verify that the ambient light level is not too high. ---The light comes on for no apparent reason 1. -
Page 17: Fcc Statement
FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.