Table of Contents
Advertisement
Available languages
Available languages
Quick Links
ASSEMBLY AND INSTALLATION
T0698 / T0699
WARNING:
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
Hardware Package (included):
Mounting Screw X2
Mounting Screw X2
#6/32 X1/2 in
#8/32X1/2 in
Tools Needed:
(1) Phillips-head Screwdriver
Important to Know:
1. If you are not familiar with state and local electrical
codes, it is recommended that you consult with a
qualified electrician.
2. This fixture requires a 120 VAC, 60 Hz power
source.
3. For general safety and to avoid any possible
damage to the sensor, be sure the power is
switched "off" before adjustment.
Maximum Wattage: 25 W
Working Temperature Range: -
Note: Fixture can be wall mounted or eave mounted.
Wall Mounted
Read notes section on page 4 for additional information about mounting location of fixture.
Light fixture and sensor should be mounted as shown above when installed (depending upon type of installation)
Before installing the light fixture under an eave, the sensor head must be rotated as shown in the next two steps for
proper operation and to avoid the risk of electrical shock.
For eave mounted only:
Swing the sensor head towards the back plate.
Backplate
INSTRUCTIONS
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Mounting Screw X2
Mounting Strap
#10/24 X1/4 in
(2) 1/8" Flat-head Screwdriver
13°F ~ 113°F
Controls
Page 1 / 5
Fixture Mounting Screw
Decorative cover
1. Phillips-head screwdriver for attaching mounting screws to
mounting strap, mounting bracket and fixture to mounting bracket.
2. 1/8" wide flat-head screwdriver for connecting the source wires
into the wiring terminal station on the mounting bracket.
Features:
1. Energy saving LED fixture.
2. Motion sensor: turns light ON automatically when
motion is detected and turns light OFF or remains
in low-level brightness when motion stops.
3. Photocell keeps the light OFF during daylight hours.
4. When in manual override mode, use wall switch
to keep the light ON full brightness during the night.
Eave Mounted
Rotate the sensor head clockwise 180˚ so the controls face down.
Controls
Wire Connector
Gasket
Controls
221102
Advertisement
Table of Contents
Related Manuals for Vaxcel Dualux T0698
Summary of Contents for Vaxcel Dualux T0698
- Page 1 ASSEMBLY AND INSTALLATION INSTRUCTIONS T0698 / T0699 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS. Hardware Package (included): Mounting Screw X2 Mounting Screw X2...
-
Page 2: Installation Steps
FRONT Outlet Box Light Head Decorative cover Mounting Strap Sensor Wire Connector Backplate Installation Steps Turn off the power at fuse or circuit box. 1. Install the mounting strap to the outlet box with the stamped word “FRONT” facing away from the outlet box, using two mounting screws that best fit the outlet box. -
Page 3: Adjusting The Light Head
Sensitivity of Motion Sensor ● You can adjust the sensitivity of the motion sensor by using the “SENS” knob located on the right side of the bottom surface of the sensor. (See Fig. 4) ● Adjust motion sensor sensitivity to achieve desired performance. ●... -
Page 4: Customization Options
6. Manual Override (nighttime operation only) Fig.6 ● To temporarily override the settings in “OFF” or “AUTO” or “3H” mode for on-demand continuous high-level brightness at night, turn the wall switch off then turn it Turn wall switch OFF-ON-OFF-ON in 0.5~3 Seconds on twice within 3 seconds, the light remains on all night long. - Page 5 The following parts are available for re-order if damaged or missing. Mounting Screw X2 Mounting Screw X2 Mounting Screw X2 Wire Connector Gasket Mounting Strap Fixture Mounting Screw Decorative cover #10/24 X1/4 in #6/32 X1/2 in #8/32X1/2 in Assembly Kit 6611MM (1 SET) FOR T0698 6612MM (1 SET) FOR T0699 A: 7-1/4"...
-
Page 6: Herramientas Necesarias
INSTRUCCIONES DE ENSAMBLAJE E INSTALACIÓN T0698 / T0699 ADVERTENCIA: PARA EVITAR EL RIESGO DE CHOQUE ELÉCTRICO, ASEGÚRESE DE APAGAR LA ENERGÍA ANTES DE INSTALAR O HACER EL MANTENIMIENTO DE ESTE ARTEFACTO. NOTAS: 1. Antes de instalar, consulte los códigos de electricidad locales para ver los requisitos de cableado y conexión a tierra. - Page 7 FRONT Caja de Cabezal de iluminación toma de corriente Cubierta decorativa Placa de montaje Sensor Conector de cable Placa posterior Pasos de la instalación Apague la corriente en la caja de fusibles o de circuitos. 1. Instale la placa de montaje a la caja de toma de corriente, con la palabra "FRONT" (frente) hacia afuera, usando dos tornillos de montaje que se ajusten mejor a la caja de toma de corriente.
-
Page 8: Funciones Y Operaciones
Sensibilidad del sensor de movimiento ● Puede ajustar la sensibilidad del sensor de movimiento usando la perilla de sensibilidad ("SENS") ubicada a la izquierda en la superficie inferior del sensor. (Vea la Fig. 4) ● Ajuste la sensibilidad del sensor de movimiento para lograr el rendimiento deseado. ●... -
Page 9: Resolución De Problemas
6. Desactivación manual (solo funcionamiento nocturno) Fig.6 ● Para desactivar temporalmente los ajustes en los modos de apagado, automático o de 3 horas para brillo de nivel alto continuo a demanda durante la noche, apague ("OFF") y Apague-Encienda-Apague-Encienda el encienda ("ON") el interruptor de pared dos veces en un lapso interruptor de pared en 0.5 ~ 3 segundos de 3 segundos, la luz permanecerá... - Page 10 Las siguientes piezas están disponibles para pedido si están dañadas o faltan. Tornillo de montaje X2 Tornillo de montaje Tornillo de montaje X2 Tornillo de montaje X2 Conector de cable Empaquetadura Placa de montaje Cubierta decorativa 10/24 X1/4 in del artefacto 6/32 X1/2 in 8/32X1/2 in Kit de ensamblaje...