Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Vaxcel Manuals
  4. Outdoor Light
  5. T0692
  6. Assembly and installation instructions

Vaxcel T0692 Assembly And Installation Instructions

Hide thumbs Also See for T0692:
1
2
3
4
5

Advertisement

Quick Links

Download this manual
ASSEMBLY AND INSTALLATION
T0692 / T0693
WARNING:
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
Hardware Package (included):
Mounting Screw X2
Mounting Screw X2
#8/32X1/2 in
#6/32 X1/2 in
Important to Know:
1. If you are not familiar with state and local electrical
codes, it is recommended that you consult with a
qualified electrician.
2. This fixture requires a 120 VAC, 60 Hz power
source.
3. For general safety and to avoid any possible
damage to the sensor, be sure the power is
switched "off" before adjustment.
Maximum Wattage: 2-150 W (bulb not included)
Working Temperature Range: -
Note: Fixture can be wall mounted or eave mounted.
Wall Mounted
Read notes section on page 4 for additional information about mounting location of fixture.
Light fixture and sensor should be mounted as shown above when installed (depending upon type of installation)
Before installing the light fixture under an eave, the sensor head must be rotated as shown in the next two steps for
proper operation and to avoid the risk of electrical shock.
For eave mounted only:
Rotate the sensor head towards the back plate.
Backplate
INSTRUCTIONS
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Mounting Screw X2
Mounting Strap
#10/24 X1/4 in
13°F ~ 113°F
Controls
Page 1 / 5
Decorative cover
Fixture Mounting Screw
Features:
1. Motion sensor: turns light ON automatically when
motion is detected and turns light OFF or remains
Low-level brightness when motion stops.
2. Photocell keeps the light OFF during daylight hours.
Eave Mounted
Rotate the sensor head clockwise 180˚ so the controls face down.
Controls
Wire Connector
Gasket
Controls
221021

Advertisement

loading

Related Manuals for Vaxcel T0692

Summary of Contents for Vaxcel T0692

  • Page 1 ASSEMBLY AND INSTALLATION INSTRUCTIONS T0692 / T0693 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS.

  • Page 2: Installation Steps

    Decorative Cover FRONT Outlet Box PAR 38 Bulb Max.150W (not included) Mounting Strap Sensor Wire Connector Backplate Installation Steps Turn off the power at fuse or circuit box. 1. Install the mounting strap to the outlet box with the stamped word “FRONT” facing away from the outlet box, using two mounting screws that best fit the outlet box.

  • Page 3: Functions And Operations

    Fig. 2 Fig. 3 Sensor Adjustment Lower For Short Coverage Sensitivity of Motion Sensor ● You can adjust the sensitivity of the motion sensor by using the “SENSITIVITY” selector located on the right side of the bottom surface of the sensor. (See Fig. 4) ●...
  • Page 4 Functions and Operations (continued) 4. PC MODE (nighttime operation only) ● In "PC" mode, the light will turn on at full brightness at dusk and remains on until dawn. 5. 3 HOURS (3H) MODE (nighttime operation only) ● In “3H” mode, the light turns to high-level brightness at dusk, and stays "ON" for 3 hours, then it turns to low-level brightness.

  • Page 5: Troubleshooting

    Gasket #8/32X1/2 in #6/32 X1/2 in #10/24 X1/4 in Assembly Kit 6605MM (1 SET) FOR T0692 6606MM (1 SET) FOR T0693 Troubleshooting ---The light does not work. 1. Make sure the wall switch and circuit breaker are on. 2. Make sure the wiring is correct.

This manual is also suitable for:

T0693