Advertisement
Quick Links
ASSEMBLY AND INSTALLATION
T0696 / T0697
WARNING:
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
Hardware Package (included):
Mounting Screw X2
Mounting Screw X2
#8/32X1/2 in
#6/32 X1/2 in
Important to Know:
1. If you are not familiar with state and local electrical
codes, it is recommended that you consult with a
qualified electrician.
2. This fixture requires a 120 VAC, 60 Hz power
source.
3. For general safety and to avoid any possible
damage to the sensor, be sure the power is
switched "off" before adjustment.
Maximum Wattage: 2-150 W (bulb not included)
Working Temperature Range: -
Note: Fixture can be wall mounted or eave mounted.
Wall Mounted
Read notes section on page 4 for additional information about mounting location of fixture.
Light fixture and sensor should be mounted as shown above when installed (depending upon type of installation)
Before installing the light fixture under an eave, the sensor head must be rotated as shown in the next two steps for
proper operation and to avoid the risk of electrical shock.
For eave mounted only:
Rotate the sensor head towards the back plate.
Backplate
INSTRUCTIONS
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Mounting Screw X2
Mounting Strap
#10/24 X1/4 in
13°F ~ 113°F
Controls
Page 1 / 5
Decorative cover
Fixture Mounting Screw
Features:
1. Motion sensor: turns light ON automatically when
motion is detected and turns light OFF or remains
Low-level brightness when motion stops.
2. Photocell keeps the light OFF during daylight hours.
Eave Mounted
Rotate the sensor head clockwise 180˚ so the controls face down.
Controls
Wire Connector
Gasket
Controls
221021
Advertisement
Related Manuals for Vaxcel T0696
Summary of Contents for Vaxcel T0696
- Page 1 ASSEMBLY AND INSTALLATION INSTRUCTIONS T0696 / T0697 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS.
-
Page 2: Installation Steps
Decorative Cover Decorative Shell FRONT Outlet Box PAR 38 Bulb Max.150W (not included) Mounting Strap Wire Connector Backplate Installation Steps Turn off the power at fuse or circuit box. 1. Install the mounting strap to the outlet box with the stamped word “FRONT” facing away from the outlet box, using two mounting screws that best fit the outlet box. -
Page 3: Adjusting The Light Head
Fig. 2 Fig. 3 Sensor Adjustment Lower For Short Coverage Sensitivity of Motion Sensor ● You can adjust the sensitivity of the motion sensor by using the “SENSITIVITY” selector located on the right side of the bottom surface of the sensor. (See Fig. 4) ●... -
Page 4: Customization Options
Functions and Operations (continued) 5. 3 HOURS (3H) MODE (nighttime operation only) ● In “3H” mode, the light turns to high-level brightnes at dusk, and stays "ON" for 3 hours, then it turns to low-level brightness. It turns to high-level brightness when motion is detected, and stays on as long as motion continues. When motion is no longer detected, it remains on for the predetermined shut-off delay time you set (30s/1min/3min), then returns to the low-level brightnessautomatically. -
Page 5: Troubleshooting
Gasket #8/32X1/2 in #6/32 X1/2 in #10/24 X1/4 in Assembly Kit 6609MM (1 SET) FOR T0696 6610MM (1 SET) FOR T0697 Troubleshooting ---The light does not work. 1. Make sure the wall switch and circuit breaker are on. 2. Make sure the wiring is correct.