Vaxcel T0274 Assembly And Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Vaxcel Manuals
  4. Outdoor Light
  5. T0274
  6. Assembly and installation instructions manual

Vaxcel T0274 Assembly And Installation Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ASSEMBLY AND INSTALLATION
T0274 / T0275
WARNING:
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
Hardware Package (included):
Mounting Screw X2
Mounting Screw X2
#8/32X1/2 in
#6/32 X1/2 in
Important to Know:
1. If you are not familiar with state and local electrical
codes, it is recommended that you consult with a
qualified electrician.
2. This fixture requires a 120 VAC, 60 Hz power
source.
3. For general safety and to avoid any possible
damage to the sensor, be sure the power is
switched "off" before adjustment.
Maximum Wattage: 29 W
Working Temperature Range: -4 0 F ~ 113 0 F
Note: Fixture can be wall mounted or eave mounted.
Wall Mounted
Read notes section on page 4 for additional information about mounting location of fixture.
Light fixture and sensor should be mounted as shown above when installed (depending upon type of installation)
Before installing the light fixture under an eave, the sensor head must be rotated as shown in the next two steps for
proper operation and to avoid the risk of electrical shock.
For eave mounted only:
Swing the sensor head towards the mounting bracket.
INSTRUCTIONS
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Mounting Screw X2
Mounting Bracket Screw
#10/24 X1/4 in
Mounting Bracket
Controls
Mounting Strap
Features:
1. Energy saving LED fixture.
2. Motion sensor: turns light ON automatically when
motion is detected and turns light OFF automatically
when motion stops.
3. Photocell keeps the light OFF during daylight hours.
Rotate the sensor head clockwise 180˚ so the controls face down.
Page 1 / 10
Decorative cover
Fixture Mounting Screw
Eave Mounted
Controls
160826
Controls

Advertisement

Table of Contents
loading

Related Manuals for Vaxcel T0274

Summary of Contents for Vaxcel T0274

  • Page 1 ASSEMBLY AND INSTALLATION INSTRUCTIONS T0274 / T0275 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS.

  • Page 2: Installation Steps

    Mounting Bracket Mounting Bracket Screw FRONT Back Plate Light Head Decorative cover Outlet Box Sensor Mounting Strap Installation Steps Turn off the power at fuse or circuit box. Fig. 1 1. The fixture mounting bracket is pre-assembled on the light fixture. Unscrew both the decorative cover and the fixture mounting screw in order to remove the mounting bracket.

  • Page 3: Function And Operation

    2. You can rotate the sensor head up and down to change the coverage area (See Fig. 2). Walk through the detection zone at the farthest distance you wish to detect motion. Note: Range set too high may increase false triggering. (See Fig. 3 and Fig. 4) Fig.
  • Page 4 3. CUSTOM SETTINGS MODE (nighttime operation only) Set motion-sensor operation to go on at a specified time, turn the wall switch “OFF” and then ● turn it “ON” within 3 seconds at that time. The light will go into motion-sensor operation at the specified time every night.
  • Page 5 User Guide Setting for single light through mobile device (Take iOS for example as below. Android will be slightly different). Before you start 4.If there is a light in the bluetooth cover range, the ● Turn on bluetooth on mobile device.

  • Page 6: Choose Mode

    Set picture for light Use light in “Custom settings” mode 9. Click Fig.8 “Change image”. And click “take photo” to take 7. Select “Custom Settings” in a photo . Manual Override for 9:41 AM 100% Back Customize Early Evening Mode setting, and choose option between “Duration”...
  • Page 7 9.3. Android:Adjust the photo to trim the photo’s desired 10. Click fig.9 “Change existing size. Then click “ ” . photo” to choose a desired iOS: Click“Done” to take a photo. image on your device. Then 9:41 AM 100% click “Cancel” back to Back “Setting”...

  • Page 8: Restore Factory Defaults

    Set password for light 13.1 Keep pressing the “reset” 12. Click fig.8 “Password” to set button on the light for 5 a password for bluetooth seconds, the light will flash 9:41 AM 100% 9:41 AM 100% device so that others need three times.

  • Page 9: Spare Parts List

    Mounting Screw X2 Mounting Screw X2 Mounting Strap Decorative cover Mounting Bracket Screw Fixture Mounting Screw #8/32X1/2 in #6/32 X1/2 in #10/24 X1/4 in Assembly Kit 5569MM (1 SET) for T0274 5570MM (1 SET) for T0275 Page 9 / 10 160826...

  • Page 10: Year Limited Warranty

    5-YEAR LIMITED WARRANTY: All products are warranted to be free of defects in material and workmanship for five (5) years from date of purchase. This warranty is limited to the correction of any such defect, or the replacement of any such defective item(s), provided that: (a) we are properly notified and consent to return of the item(s) in question:(b) the item(s) is / are returned with proof of purchase date;...

This manual is also suitable for:

T0275

Table of Contents