HunterDouglas Alustra Woven Textures Standard ST30 Installation Operation Care
Roller shades, designer roller and screen shades
Hide thumbs
Also See for Alustra Woven Textures Standard ST30:
- Installation operation care (36 pages)
Subscribe to Our Youtube Channel
Related Manuals for HunterDouglas Alustra Woven Textures Standard ST30
Summary of Contents for HunterDouglas Alustra Woven Textures Standard ST30
- Page 1 Installation • Operation • Care Alustra Woven Textures ® ® Roller Shades, Designer Roller and Screen Shades ST30, ST50, and LT525 Standard, Coupled, and Pocket...
-
Page 2: Table Of Contents
CONTENTS GETTING STARTED ............3 Product View — ST30 ............ 3 Product View — ST50 and LT525 ........4 Product View — Coupled Shades ST50 and LT525 ..5 INSTALLATION .............. 6 Installation Overview ............. 6 Mount the Installation Brackets — ST30 ...... 8 Mount the Installation Brackets —... -
Page 3: Getting Started
GETTING STARTED Product View — ST30 Standard Motorized Shade Bracket Antenna Motor Bracket Wire Assembly Pocket End Cap Power Cord Power Supply Power Plug Pocket Assembly Pocket Pocket End Cap Pocket Bottom (Optional) -
Page 4: Product View - St50 And Lt525
GETTING STARTED Product View — ST50 and LT525 Standard Motorized Shade Idle-Side Motor-Side Bracket Motor Bracket Assembly Power Cord Power Plug Pocket End Cap Pocket Motorized Shade Pocket Idle-Side Pocket Bracket End Cap Pocket Bottom (Optional) Motor-Side Bracket Motor Assembly Power Cord Power... -
Page 5: Product View - Coupled Shades St50 And Lt525
GETTING STARTED Product View — Coupled Shades ST50 and LT525 Blade End Plug Motor Assembly Motorized Panel (Can Be on Either End of Shade Assembly) Motor-Side Bracket Power Cord Power Plug Blade End Plug Slot End Plug Center Panel (0 – 3 shade panels may be installed between the motorized panel and end panels.) Intermediate... -
Page 6: Installation
INSTALLATION Installation Overview Thank you for purchasing Hunter Douglas motorized roller shades. With proper installation, operation, and care, your new shades will provide years of beauty and performance. Please thoroughly review this instruction booklet and the enclosed packing list before beginning the installation. - Page 7 INSTALLATION Installation Brackets for ST50 and LT525 Motor-Side Idle-Side ■ Motor. The installation brackets are supplied in pairs. The bracket with a spring clip is used for the motor-side of the shade and the idle-side bracket is used for the idle-side of the shade. Intermediate Bracket for Coupled Shades.
-
Page 8: Mount The Installation Brackets - St30
INSTALLATION Mount the Installation Brackets — ST30 The two installation brackets for ST30 motor are identical. Bracket Inside Mount Shades. Place each of the brackets on the ■ Inside Mount inside of the window casement. Mark the screw holes. The minimum mounting depth required and fully ➤... -
Page 9: Mount The Installation Brackets - St50/Lt525
INSTALLATION Mount the Installation Brackets — ST50/LT525 The bracket with a spring clip is used for the ■ Motor-Side Idle-Side motor-side of the shade. The brackets can be used for inside, outside, ■ or ceiling mount. The brackets are always installed so the inner ■... - Page 10 INSTALLATION Idle-Side Bracket Inside/Ceiling Mount Place the idle-side bracket over the loaded spring pin on ■ the end of the shade. Place the shade into the motor-side bracket. Do not install ■ the spring clip. Placement for Outside Spring Mount Loaded Pin Hold the shade and idle-side bracket in the desired ■...
- Page 11 INSTALLATION Coupled Shades There are three types of brackets: ■ The bracket with a spring clip is used for the motor-side of the shade. ➤ The bracket with the bronze bushing is the center or intermediate bracket. It faces ➤ the idle-side bracket. The idle-side bracket is used for the idle-side of the shade.
- Page 12 INSTALLATION Motor-Side Bracket (Motor Panel) Remove the spring clip from the bracket and set it aside. ■ Position the motor-side bracket using your marks, then mark each of the screw holes. ■ Drill the screw holes using a " drill bit. ■...
- Page 13 INSTALLATION Use a level to check that the mounting surface is level. Shim the brackets if necessary. ■ Shims are not provided. Attach the intermediate bracket using the screws provided. ■ Put the second panel in place so that the slotted end plug engages the blade end plug of ■...
- Page 14 INSTALLATION Use a level to check that the mounting surface is level. Shim the brackets if necessary. ■ Shims are not provided. Attach the idle-side bracket using the screws provided. ■ Install the last panel, placing the spring-loaded pin into the idle-side bracket. Push it into ■...
-
Page 15: Install The Shade
INSTALLATION Install the Pocket Locate the studs or other substantial material for ■ your mounting surface. WARNING: Product is heavy. Mount into wood/metal studs or into concrete with concrete anchors. Drywall anchors are not recommended. Mark the pocket for the locations you have chosen ■... - Page 16 INSTALLATION Install the Motor End Align and insert the motor mount with the holes in the bracket. Motor ■ Mount CAUTION: Make sure the antenna wire is not pinched or caught between the bracket and motor mount. Do not cut the antenna wire or wrap it around the power cord.
-
Page 17: Attach Optional Components
INSTALLATION Attach Optional Components Attach the Bottom Pocket Place the bottom into the pocket at an angle. ■ Hook the bottom to the ledge inside the pocket and rotate it down to ■ secure it into place. Install End Caps — Standard Outside Mount (Optional) Install the bracket covers by aligning the bracket with the channels in ■... - Page 18 INSTALLATION NOTE TO INSTALLER: To connect the 5- or 10-amp power supply to the home electrical system, a 16-gauge wire is sufficient for the 110V AC input. This wire is not provided with your shade order. Two-shade power supplies (DR-120-24) use a switch to select between 100-120V AC ➤...
-
Page 19: Operation
OPERATION Remote Control Operation Remote Controls Shown at the right are the wireless wall switch ■ and the hand-held remote control. (The multi- channel versions are similar − see “Multi- Channel Controls” below.) IMPORTANT: Mount the wireless wall switch in a non-metal box. Multi-Channel Controls The channel light on the multi-channel hand-held ■... -
Page 20: Operate The Shade
OPERATION Operate the Shade Your Hunter Douglas motorized shade has been pre-programmed with upper and lower limits specifically customized for your window. To Lower the Shade Press and release the DOWN button on the remote control. The shade will fully lower. ■... - Page 21 OPERATION Clear Motor Memory and Return to Factory Mode Press and hold the PROGRAM button until the shade jogs twice (once immediately and a ■ second time about seven seconds later). Programming the Motorized Shade Press the UP and DOWN buttons simultaneously. Hold the buttons down until the shade ■...
- Page 22 OPERATION Reset the Top Limit Press the UP button. The shade raises to the top limit. ■ Press the UP and DOWN buttons until the shade jogs up and down. ■ Press the UP or DOWN buttons to fine tune the top limit. ■...
-
Page 23: Shade Adjustment
OPERATION To Add a Transmitter: Press the PROGRAM button on the back of the original hand-held remote or on the side ■ of the wireless wall switch on an established channel until the shade jogs. Select the transmitter to add. ■ Press the PROGRAM button on the back of the new hand-held remote or on the right ■... -
Page 24: Limit Adjustments For Standard Motor Shades
OPERATION Limit Adjustments for Standard Motor Shades Your Hunter Douglas motorized shade has been pre-set with upper and lower limits specifically customized for your window. If you need to change the custom settings, follow the steps in this section. IMPORTANT: The button farthest from you sets the lower limit of the shade and the button closest to you sets the upper limit of the shade. -
Page 25: Using The St30 Motor Buttons
OPERATION Using the ST30 Motor Buttons There are two small buttons on the end of the ST30 motor (these buttons do not exist on the ST50 motor). The buttons are accessible from the underside of the motor. The smaller round button is used as a reset button. ■... -
Page 26: Troubleshooting
TROUBLESHOOTING Troubleshooting If your shade is not operating correctly: Review the digital support guide for your control device. ■ Refer to the following troubleshooting procedures for specific solutions for your shade. ■ If questions remain, please contact Hunter Douglas Consumer Support at (800) 789-0331. Problem The shade raises or lowers unevenly. -
Page 27: Care
CARE Removing the Shade (If Necessary) Remove the Shade from the Brackets ST30 Motor Standard and Pocket Shades Unplug the shade or otherwise disconnect the power cord to the shade. ■ While holding the top of the shade, insert a flat blade ■... - Page 28 CARE Coupled Shades IMPORTANT: The shade panels must be removed in the reverse order in which they were installed. If possible, place all of the panels in the fully opened position. ■ Remove power to the shade. ■ End Panel This is the panel farthest from the motor. Grasp the end panel and push it against the idle-side bracket to compress the spring.
-
Page 29: Cleaning Procedures
CARE Pocket Shades Remove the bottom cover. ■ Once the shade is removed from the brackets ■ in the pocket, the pocket can be removed by unscrewing the installation screws. Lift up the edge of the bottom cover. ■ Disengage it from the ledge of the pocket. ■... -
Page 30: Declarations
Hunter Douglas hereby declares that the PV36 is in compliance with the essential requirements and other relevant provisions of Electromagnetic Compatibility (EMC) Directive 2014/30/EU and Radio Equipment Directive (RED) 2014/53/EU. A copy of the DoC can be obtained online: www.hunterdouglas.com/RFcertifications. -
Page 31: Child Safety
CHILD SAFETY... -
Page 32: Warranty
If you are not thoroughly satisfied, simply contact Hunter Douglas at (800) 789-0331 or visit hunterdouglas.com. In support of this policy of consumer satisfaction, we offer our Lifetime Limited Warranty as described below.
Need help?
Do you have a question about the Alustra Woven Textures Standard ST30 and is the answer not in the manual?
Questions and answers