Table of Contents
Advertisement
Quick Links
Black Electric Single Motor Desk Frame with
Rear-Set Legs
Instruction Manual
SKU: DESK-100E-RB
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
https://vivo-us.com/products/desk-100e-rb
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
help@vivo-us.com
www.vivo-us.com
Chat live with an agent!
309-278-5303
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Vivo DESK-100E-RB
Summary of Contents for Vivo DESK-100E-RB
- Page 1 Black Electric Single Motor Desk Frame with Rear-Set Legs Instruction Manual SKU: DESK-100E-RB Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. https://vivo-us.com/products/desk-100e-rb GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST help@vivo-us.com...
- Page 2 WARNING! If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury.
- Page 3 ASSEMBLY STEPS STEP 1 Attach Left Crossbar (A) to Leg (D) and Right Crossbar (B) to Motorized Leg (E) using M6x11mm Screws (S-A) and 5mm Allen Wrench (T-A). Connect Left Side Bracket (F) to Leg (D), and Right Side Bracket (G) to Motorized Leg (E) using M6x11mm Screws (S-A) and 5mm Allen Wrench (T-A).
- Page 4 STEP 2 Install Feet (C) to Leg (D) and Motorized Leg (E) using M6x11mm Screws (S-A) and 5mm Allen Wrench (T-A). Note: Feet should extend in the same direction of side brackets. STEP 3 Insert Crossbar (H) into Left Crossbar (A) and Right Crossbar (B). Adjust the desk frame assembly to the desired length and then insert M6x11mm Screws (S-A) into Left Crossbar (A) and Right Crossbar (B).
- Page 5 STEP 4 Loosen the nut on Sync Rod (I) and insert the hex rod end into Leg (D). While holding the hex end, pull the larger rod out until the connector engages with Motorized Leg (E). Tighten the set screw on Sync Rod (I) using 2mm Allen Wrench (T-B), then tighten the nut.
- Page 6 STEP 6 Place the assembled frame upside down on the tabletop. Adjust width as needed. If not using a VIVO desktop with pre-drilled holes, drill 10mm deep pilot holes using a 1/8” (3mm) drill bit. Secure the frame to the tabletop using M5x16mm Screws (S-B). Tighten with a Phillips screwdriver.
- Page 7 STEP 7 Connect AC Adapter (K) and cables from Motorized Leg (E) to Control Panel (J), as shown below. Turn the desk right side up and plug AC Adapter (K) into an AC power outlet. Manage cables using Cable Clips (M). Refer to Controller User Guide for operational instructions. CAUTION! Keep area of vertical Keep weight on desk...
- Page 8 AVG. RESPONSE TIME (within office hrs) - 23% within < 15m - 38% within < 30m - 61% within < 1hr - 83% within < 2hr - 92% within < 3hr FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com...
Need help?
Do you have a question about the DESK-100E-RB and is the answer not in the manual?
Questions and answers