Advertisement
Quick Links
NS3503-16P-4C-V2 Quick Installation
Guide
Introduction
Thank you for purchasing IFS L2/L4 Managed Gigabit
Ethernet Switch. The description of this model is shown
below:
NS3503-16P-4C-V2
16-port 10/100/1000T 802.3bt PoE + 4-port
Gigabit TP/SFP Combo Managed Switch 16-
port
"Managed Switch" is used as an alternative name in
this Quick Installation Guide.
Open the box of the Managed Switch and carefully
unpack it. The box should contain the items listed below:
Package Contents
Model Series
Model Name
Package Item
The Managed Switch
Quick Installation Guide
RS-232 to RJ45 Console Cable
Rubber Feet
Two Rack-mounting Brackets with
Attachment Screws
Power Cord
SFP Dust Caps
If any item is found missing or damaged, please contact
your local reseller for replacement.
Requirements
Workstations running Windows
XP/2003/Vista/7/8/2008/10, MAC OS X or later,
Linux, UNIX, or other platforms are compatible with
TCP/IP protocols.
P/N 1073220 • REV C • ISS 03JUL22
© 2021 Carrier. All rights reserved. Specifications subject to change without prior notice.
NS3503-16P-4C-V2
NS3503-16P
1
1
1
4
2
1
4
Workstations are installed with Ethernet NIC
(Network Interface Card)
Serial Port Connection (Terminal)
The above Workstations come with COM Port
(DB9) or USB-to-RS-232 converter.
The above Workstations have been installed
with terminal emulator, such as Hyper Terminal
included in Windows XP/2003.
Serial cable -- One end is attached to the RS-
232 serial port, while the other end to the
console port of the Managed Switch.
Ethernet Port Connection
Network cables -- Use standard network (UTP)
cables with RJ45 connectors.
The above PC is installed with Web browser and
JAVA runtime environment plug-in.
Note: It is recommended to use Internet Explore 8.0 or
above to access the Managed Switch. If the Web
interface of the Managed Switch is not accessible,
please turn off the anti-virus software or firewall and then
try it again.
Terminal Setup
The Managed Switch is equipped with a console
interface for local switch setup and maintenance. To
configure the system, connect a serial cable to a COM
port on a PC or notebook computer and to the RJ45
type of the console port of the Managed Switch.
Figure 1: Managed Switch Console Connectivity
1
Advertisement
Related Manuals for ifs NS3503-16P-4C-V2
Summary of Contents for ifs NS3503-16P-4C-V2
- Page 1 Guide Introduction Workstations are installed with Ethernet NIC (Network Interface Card) Thank you for purchasing IFS L2/L4 Managed Gigabit Serial Port Connection (Terminal) Ethernet Switch. The description of this model is shown below: The above Workstations come with COM Port ...
- Page 2 Switch, please use the procedures as follows: Show the current IP address 1. At the ”NS3503-16P-4C-V2#” prompt, enter “show 2. The screen displays the current IP Address, Subnet Mask and Gateway as shown below. Figure 4: IP Information Screen...
- Page 3 254, except 100), and the default subnet mask is 255.255.255.0. Figure 10: User name and password change Figure 7: IP Management Diagram After typing the new username and password in the login window, the main screen appears as shown in figure below. NS3503-16P-4C-V2 Quick Installation Guide...
- Page 4 10 seconds. After the device is rebooted, you can login the management Web interface within the same subnet of 192.168.0.xx. Figure 13: NS3503-16P-4C-V2 Reset Button Now, you can use the Web management interface to continue the Switch management.