Advertisement
Quick Links
NS3552-16P-2T-2S-V2 Quick Installation Guide
Figure 1: NS3552-16P-2T-2S-V2 Industrial L2+ Multi-port Full
Gigabit Managed Ethernet Switch
Package contents
Thank you for purchasing the NS3552-16P-2T-2S-V2 IFS L2+
industrial managed switch. The descriptions of this model are
as follows:
Industrial 16-Port 10/100/1000T 802.3at PoE +
2-Port 10/100/100T
+ 2-Port 100/1000X SFP Managed Switch
Unless specified, the term "industrial managed switch"
mentioned in this quick installation guide refers to the NS3552-
16P-2T-2S-V2.
Open the box of the industrial managed switch and carefully
unpack it. The box should contain the following items:
The industrial managed switch × 1
Quick installation guide × 1
DIN rail kit × 1
Wall mounting kit × 1
DB9 to RJ45 interface RS232 console cable × 1
Dust cap (see the table below)
RJ45 Dust Cap
NS3552-16P-2T-
2S-V2
P/N 1073645-EN • REV E • ISS 04JUL22
SFP Dust Cap
19
2
If any of these are missing or damaged, contact your dealer
immediately. If possible, retain the carton including the original
packing materials for repacking the product in case there is a
need to return it to us for repair.
Requirements
The industrial managed switch
interface for management purposes. The following equipment
is necessary for further management:
Workstations running Windows
2008 / 10, MAC OS X or later, Linux, UNIX, or other
platforms are compatible with TCP/IP protocols.
Workstations are installed with Ethernet NIC (Network
Interface Card)
Serial port connection (Terminal)
The above workstations come with a COM Port (DB9)
or USB-to-RS232 converter.
The above workstations have been installed with a
terminal emulator, such as Tera Term, PuTTY, or
Hyper Terminal included in Windows.
Serial cable – One end is attached to the RS232
serial port, and the other end is attached to the
console port of the managed switch.
Ethernet port connection
Network cables – Use standard network (UTP) cables
with RJ45 connectors.
The above workstations have a web browser and
JAVA runtime environment plug-in installed.
Note: We recommend using Internet Explorer 11.0 or later to
access the industrial managed switch. If the web interface of
the industrial managed switch is not accessible, turn off the
anti-virus software or firewall and then try it again.
Wiring the power inputs
The upper panel of the industrial managed switch indicates a
DC inlet power socket and consists of one terminal block
connector within six contacts. Follow the steps below to insert
the power wire:
1.
Insert the positive/negative DC power wires into contacts 1
and 2 for Power 1, or 5, and 6 for Power 2.
NS3552-16P-2T-2S-V2 : DC 48~56V
provides a
remote login
®
XP / 2003 / Vista / 7 / 8 /
1 / 6
Advertisement
Related Manuals for ifs NS3552-16P-2T-2S-V2
Summary of Contents for ifs NS3552-16P-2T-2S-V2
- Page 1 Serial cable – One end is attached to the RS232 serial port, and the other end is attached to the Thank you for purchasing the NS3552-16P-2T-2S-V2 IFS L2+ console port of the managed switch. industrial managed switch. The descriptions of this model are Ethernet port connection ...
- Page 2 Figure 2: NS3552-16P upper panel Place the bottom of DIN-rail lightly into the track. Tighten the wire-clamp screws to prevent the wires from loosening. Ensure that the DIN-rail is secured to the track. Power 1 Power 2 Positive (+) Pin Negative (-) Pin NS3552-16P Pin 1/5...
-
Page 3: Terminal Setup
Remove the DIN-rail from the industrial gigabit Ethernet switch. Loosen the screws to remove the DIN-rail. Place the wall-mount plate on the rear panel of the industrial gigabit Ethernet switch. Log in to the console. After the terminal has been connected to the device, power on the industrial managed switch. -
Page 4: Starting Web Management
Configuration of the IP address At the “#” prompt, type the following command and press Enter as shown in Figure 6. NS3552-16P-2T-2S-V2# configure terminal NS3552-16P-2T-2S-V2 (config)# interface vlan 1 NS3552-16P-2T-2S-V2 (config-if-vlan)# ip address 192.168.1.100 255.255.255.0 The previous command would apply the following settings for the industrial managed switch. -
Page 5: Resetting The Switch To Default
becomes the startup configuration file (i.e., the saved configuration). To save all applied changes and set the current configuration as a startup configuration, the startup-configuration file is loaded automatically across a system reboot. Click System > Save Startup Config. When the success window appears, click OK. After typing the new username and password in the login window, the main screen appears. -
Page 6: Contact Information
Carrier, except where specifically permitted under US and international copyright law. Trademarks and IFS names and logos are a product brand of patents Aritech, a part of Carrier. Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.