Table of Contents
Advertisement
5|
Either arc amount or arc time does not change.
•
On SM, NZ, MM or AUTO mode, either arc amount or arc time does not change. Implement [Arc
Calibration] and the arc amount on these modes properly maintain. When used in another mode, arc
amount and arc time are automatically set to prevent their alteration.
6|
Set pause.
•
Refer to [Option menu].
3. Product Outline
3.1. Function buttons
7|
Indicate cleaved angle, fi ber angle, and clad deviation.
BUTTON
•
Refer to [Option menu].
Press and hold about 1 second to turn the power on/off.
3. Product Outline
Move the cursor to the left.
Move fiber to manual mode and adjust the camera's focus.
3.1. Function buttons
Stripping popup menu should load.
8|
Estimated splice loss and measured splice loss do not match.
Move the cursor to the right.
Move fiber to manual mode and adjust the camera's focus.
•
The estimated splice loss is a calculated value so it should be used only as a reference.
Move the cursor upward.
Move each motor to manual mode.
Splice popup menu should load.
Move the cursor downward.
Move each motor to manual mode.
Heater popup menu should load.
9.3|
SLEEVE HEATER
Initialize the splice function.
Return to the menu screen.
1|
Fiber protecting sleeve does not contract completely.
Complete a selection.
Follow the next step on the menu screen.
•
Increase the heating time. Refer to [Heater mode edition].
Splice execution.
2|
The heater is overheated.
Return to the initial screen and initialize splice function.
•
Stop the heater by pressing
, turn the power off and then contact UCLSWIFT.
Turn on the heater.
When it is on, the lamp on the left is in the red.
Press once more when it is on, and the heater is turned off.
•
If the protecting sleeve melts and sticks to the heater cover, remove it by pushing it with a cotton swab.
SWIFT KF4-EN, Rev.C
3|
Initialize heater mode condition.
•
Refer to [Heat mode edition].
4|
Cancel heater in the middle of an operation.
•
Heater operation cannot cancel by pressing
9.4|
OTHERS
SWIFT KF4-EN, Rev.C
1|
Restrict splice mode and heater mode setting.
•
Refer to [Menu lock].
2|
Splice mode's arc amount does not change even after [Arc calibration].
•
The internal standard arc amount does calibrate. Therefore, the arc amount of each splice mode does
not change.
3|
Forgotten password.
•
Contact UCLSWIFT.
53
DESCRIPTION
BUTTON
DESCRIPTION
3. Product Outline
Press and hold about 1 second to turn the power on/off.
3.1. Function buttons
Move the cursor to the left.
BUTTON
DESCRIPTION
Move fiber to manual mode and adjust the camera's focus.
Stripping popup menu should load.
Press and hold about 1 second to turn the power on/off.
Move the cursor to the right.
Move the cursor to the left.
Move fiber to manual mode and adjust the camera's focus.
Move fiber to manual mode and adjust the camera's focus.
Stripping popup menu should load.
Move the cursor upward.
Move the cursor to the right.
Move each motor to manual mode.
Move fiber to manual mode and adjust the camera's focus.
Splice popup menu should load.
Move the cursor upward.
Move each motor to manual mode.
Move the cursor downward.
Splice popup menu should load.
Move each motor to manual mode.
Move the cursor downward.
Heater popup menu should load.
Move each motor to manual mode.
Heater popup menu should load.
Initialize the splice function.
Initialize the splice function.
Return to the menu screen.
Return to the menu screen.
9
Complete a selection.
Complete a selection.
Follow the next step on the menu screen.
Follow the next step on the menu screen.
Splice execution.
Splice execution.
Return to the initial screen and initialize splice function.
Turn on the heater.
. Cancel it by pressing
once again.
Return to the initial screen and initialize splice function.
When it is on, the lamp on the left is in the red.
Press once more when it is on, and the heater is turned off.
Turn on the heater.
SWIFT KF4-EN, Rev.C
When it is on, the lamp on the left is in the red.
Press once more when it is on, and the heater is turned off.
9
WARRANTY AND REPAIR
Responsibility limit
For Warranty and Repair information, please contact your UCLSWIFT representative or use the contact
information found in the Help section under the information menu in the splicer unit.
10.1|
INFORMATION NECESSARY FOR REPAIR
Before sending the product, contact UCLSWIFT fi rst.
1|
Company and contact information (Name, department, company, address, contact information, fax, e-mail)
2|
Product serial number
3|
Product condition and problem incurred, error information
4|
Operating conditions, processes and uses of the splicer prior to error
10.2|
TRANSPORTATION
Please return the splicer in the carrying case provided to protect it from humidity, vibration and shock. Include
all components in the case.
10.3|
REPAIR
Customized modes, confi gurations and splice data may be lost during repair. Save test data prior to shipment
to ensure retention.
9
54
Advertisement
Table of Contents
