Heater - UCL SWIFT SWIFT KF4 User Manual

Move fiber to manual mode and adjust the camera's focus.
Move the cursor upward.
Move each motor to manual mode.
To display heater mode, press and then select "HEATER" from the menu using
Splice popup menu should load.
Move the cursor downward.
Move each motor to manual mode.
Heater popup menu should load.
Initialize the splice function.
6.2| . The selecting screen is equipped with various heater modes to facilitate easy selection.

HEATER

Return to the menu screen.
Heater mode can be expanded and saved for up to 100 modes. Heater mode Nos. 1~16 cannot
To display heater mode, press and then select "HEATER" from the menu using
Complete a selection.
Follow the next step on the menu screen.
be deleted or replaced. equipped with various heater modes to facilitate easy selection. Heater mode can be expanded and saved for
up to 100 modes. Heater mode Nos. 1—16 cannot be deleted or replaced. Splice execution.
Return to the initial screen and initialize splice function.
Turn on the heater.
When it is on, the lamp on the left is in the red.
Press once more when it is on, and the heater is turned off.
SWIFT KF4-EN, Rev.C
[Outline of heater mode]
[Outline of heater mode]
SET VALUE
SET VALUE
60mm Standard 60mm micro sleeve
60mm
40mm Standard 40mm micro sleeve
40mm
60mm IS-60
60mm IS-60 60mm micro sleeve
45mm IS-45
45mm IS-45 45mm micro sleeve
S09
3. Product Outline
S09-C
S09 45mm sleeve for 0.9mm cable
S20
3.1. Function buttons
S09-C 22mm sleeve for SOC(SC-0.9mm)
S30
S30-C
S20 45mm sleeve for 2.0mm cable
LC09/20-C
S30 45mm sleeve for 3.0mm cable
ST09-C
ST30-C
S30-C 32mm sleeve for SOC(SC-3.0mm)
3. Product Outline
LC09/20-C 25mm sleeve for SOC(LC-0.9 , 2.0mm)
Choose the right mode for each sleeve tube type and SOC. Otherwise sleeve tubes do NOT shrink
3.1. Function buttons
properly. ST09-C 28mm sleeve for SOC(ST-0.9mm)
BUTTON
ST30-C 36mm sleeve for SOC(ST-3.0mm)
!
CAUTIONS
Choose the right mode for each sleeve tube type and SOC. Otherwise sleeve tubes do NOT shrink
For the SOC, operators must use UCLSWIFT standard products. For other sleeves, see manufacturer
properly.
specifi cations and adjust manually.
For the SOC, operators must use UCLSWIFT standard products. For other sleeves, see
Heater modes specify temperature, time and heating location on the heater plate.
manufacturer specifications and adjust manually.
Heater modes specify temperature, time and heating location on the heater plate.
6.2.1 DELETION
SWIFT KF4-EN, Rev.C
First, select a heater mode by pressing . Press
27
SWIFT KF4-EN, Rev.C
Move fiber to manual mode and adjust the camera's focus.
Move the cursor upward.
Move each motor to manual mode.
Splice popup menu should load.
Move the cursor downward.
Move each motor to manual mode.
Heater popup menu should load.
Initialize the splice function.
Return to the menu screen.
. The selecting screen is
Complete a selection.
Follow the next step on the menu screen.
Splice execution.
Return to the initial screen and initialize splice function.
Turn on the heater.
When it is on, the lamp on the left is in the red.
Press once more when it is on, and the heater is turned off.
9 SWIFT KF4-EN, Rev.C
DESCRIPTION
DESCRIPTION
Standard 60mm micro sleeve
Standard 40mm micro sleeve
60mm micro sleeve
45mm micro sleeve
45mm sleeve for 0.9mm cable
22mm sleeve for SOC (SC-0.9mm)
45mm sleeve for 2.0mm cable
45mm sleeve for 3.0mm cable
BUTTON DESCRIPTION
32mm sleeve for SOC (SC-3.0mm)
Press and hold about 1 second to turn the power on/off.
25mm sleeve for SOC (LC-0.9, 2.0mm)
28mm sleeve for SOC(ST-0.9mm)
Move the cursor to the left.
Move fiber to manual mode and adjust the camera's focus.
36mm sleeve for SOC (ST-3.0mm)
Stripping popup menu should load.
Move the cursor to the right.
Move fiber to manual mode and adjust the camera's focus.
Move the cursor upward. DESCRIPTION
Move each motor to manual mode.
Splice popup menu should load.
Press and hold about 1 second to turn the power on/off.
Move the cursor downward.
Move the cursor to the left.
Move each motor to manual mode.
Move fiber to manual mode and adjust the camera's focus.
Heater popup menu should load.
Stripping popup menu should load.
Move the cursor to the right.
Initialize the splice function.
Move fiber to manual mode and adjust the camera's focus.
Return to the menu screen.
Move the cursor upward.
Move each motor to manual mode.
Splice popup menu should load. Complete a selection.
Follow the next step on the menu screen.
Move the cursor downward.
Move each motor to manual mode.
Heater popup menu should load.
Splice execution.
Initialize the splice function.
Return to the menu screen.
38
to delete. Mode Nos. 1—16 cannot be deleted.
Complete a selection.
Return to the initial screen and initialize splice function.
Follow the next step on the menu screen.
Turn on the heater.
Splice execution.
When it is on, the lamp on the left is in the red.
Press once more when it is on, and the heater is turned off.
Return to the initial screen and initialize splice function.
9
Turn on the heater.
When it is on, the lamp on the left is in the red.
Press once more when it is on, and the heater is turned off.
Move the cursor to the right.
6.2.2 Replacement
Move fiber to manual mode and adjust the camera's focus.
Move the cursor upward.
Move each motor to manual mode.
Splice popup menu should load.
Move the cursor downward.
Move each motor to manual mode.
Select a heater mode to replace, and press Heater popup menu should load.
6.2.2 REPLACEMENT
Initialize the splice function.
Return to the menu screen.
Select a heater mode to replace, and press
desired heater mode and press mode and press to replace with the selected mode.
Complete a selection.
Follow the next step on the menu screen.
Splice execution.
Return to the initial screen and initialize splice function.
Turn on the heater.
When it is on, the lamp on the left is in the red.
Press once more when it is on, and the heater is turned off.
9
SWIFT KF4-EN, Rev.C
General modes Nos. 1—16 cannot be replaced.
General modes Nos. 1~16 cannot be replaced.
SWIFT KF4-EN, Rev.C
3. Product Outline
3.1. Function buttons
BUTTON DESCRIPTION
to display heater modes on the screen. Select
Press and hold about 1 second to turn the power on/off.
to display heater modes on the screen. Select desired heater Move the cursor to the left.
Move fiber to manual mode and adjust the camera's focus.
Stripping popup menu should load.
to replace with the selected mode.
Move the cursor to the right.
Move fiber to manual mode and adjust the camera's focus.
Move the cursor upward.
Move each motor to manual mode.
Splice popup menu should load.
Move the cursor downward.
Move each motor to manual mode.
Heater popup menu should load.
Initialize the splice function.
Return to the menu screen.
Complete a selection.
Follow the next step on the menu screen.
9
Splice execution.
Return to the initial screen and initialize splice function.
Turn on the heater.
When it is on, the lamp on the left is in the red.
Press once more when it is on, and the heater is turned off.
SWIFT KF4-EN, Rev.C 9
39
28