Table of Contents
Advertisement
i.
Display heater popup menu by pressing
opup menu]
dding heater mode
[Heater popup menu]
ADDING HEATER MODE
splay heater popup menu by pressing
1|
Display heater popup menu by pressing
on the initial screen.
3. Product Outline
3.1. Function buttons
ii.
Select an empty slot by pressing
2|
Select an empty slot by pressing
ect an empty slot by pressing
iii.
Select a heater mode to add into the empty slot.
3|
Select a heater mode to add into the empty slot.
ect a heater mode to add into the empty slot.
SWIFT KF4-EN, Rev.C
eleting heater mode
DELETING HEATER MODE
elect a mode to be deleted.
1|
Select a mode to be deleted.
, Rev.C
SWIFT KF4-EN, Rev.C
elete it by pressing
.
21
on the initial screen.
3. Product Outline
on the initial screen.
3.1. Function buttons
BUTTON
DESCRIPTION
Press and hold about 1 second to turn the power on/off.
Move the cursor to the left.
Move fiber to manual mode and adjust the camera's focus.
Stripping popup menu should load.
Move the cursor to the right.
Move fiber to manual mode and adjust the camera's focus.
Move the cursor upward.
Move each motor to manual mode.
Splice popup menu should load.
Move the cursor downward.
Move each motor to manual mode.
Heater popup menu should load.
and then pressing
BUTTON
DESCRIPTION
Initialize the splice function.
Press and hold about 1 second to turn the power on/off.
Return to the menu screen.
and then pressing
Move the cursor to the left.
.
Complete a selection.
Move fiber to manual mode and adjust the camera's focus.
Follow the next step on the menu screen.
Stripping popup menu should load.
and then pressing
Move the cursor to the right.
Move fiber to manual mode and adjust the camera's focus.
Splice execution.
Move the cursor upward.
Move each motor to manual mode.
Splice popup menu should load.
Return to the initial screen and initialize splice function.
Move the cursor downward.
Move each motor to manual mode.
Turn on the heater.
Heater popup menu should load.
When it is on, the lamp on the left is in the red.
Press once more when it is on, and the heater is turned off.
Initialize the splice function.
Return to the menu screen.
SWIFT KF4-EN, Rev.C
Complete a selection.
Follow the next step on the menu screen.
Splice execution.
Return to the initial screen and initialize splice function.
Turn on the heater.
When it is on, the lamp on the left is in the red.
Press once more when it is on, and the heater is turned off.
9
29
ii.
Delete it by pressing
.
2|
Delete it by pressing
6.1. SPLICE
To display splice mode, press
displays a screen for splice mode selection as follows. The screen has a list of splice modes to
facilitate easy selection. Up to 300 splice modes can be saved. These splice modes are classified
6.1|
SPLICE
into general modes and user-defined modes.
To display splice mode, press
mode selection as follows. The screen has a list of splice modes to facilitate easy selection. Up to 300 splice
n General splice mode: Nos. 1~26
modes can be saved. These splice modes are classifi ed into general modes and user-defi ned modes.
•
General splice mode: Nos. 1 — 26
n User-defined splice mode: Nos. 27~300
•
User-defi ned splice mode: Nos. 27 — 300
9
SWIFT KF4-EN, Rev.C
[Splice modes summary]
[Splice modes summary]
SPLICE MODE
SPLICE MODE
SM
SM
NZ
DS
MM
NZ
Other
DS
29
MM
Other
Complete a selection.
Follow the next step on the menu screen.
Splice execution.
.
Return to the initial screen and initialize splice function.
3. Product Outline
3. Product Outline
Turn on the heater.
When it is on, the lamp on the left is in the red.
Press once more when it is on, and the heater is turned off.
3.1. Function buttons
3.1. Function buttons
BUTTON
DESCRIPTION
BUTTON
SWIFT KF4-EN, Rev.C
9
Press and hold about 1 second to turn the power on/off.
Move the cursor to the left.
Move fiber to manual mode and adjust the camera's focus.
Stripping popup menu should load.
Move the cursor to the right.
Move fiber to manual mode and adjust the camera's focus.
Move the cursor upward.
and select "SPLICE" menu with the
Move each motor to manual mode.
Splice popup menu should load.
Move the cursor downward.
Move each motor to manual mode.
Heater popup menu should load.
Initialize the splice function.
Return to the menu screen.
and select "SPLICE" menu with the
Complete a selection.
Follow the next step on the menu screen.
Splice execution.
Return to the initial screen and initialize splice function.
Turn on the heater.
When it is on, the lamp on the left is in the red.
Press once more when it is on, and the heater is turned off.
SWIFT KF4-EN, Rev.C
9
SWIFT KF4-EN, Rev.C
30
DESCRIPTION
DESCRIPTION
For basic SM fi ber. MFD of single mode fi ber is about 9 — 10µm at 1310nm wavelength.
For basic SM fiber. MFD of single mode fiber is about 9~10 µm at 1310
For NZDS fi ber. MFD of NZDS fi ber is about 9 — 10µm at 1550nm wavelength.
nm wavelength.
WDM fi ber can also be spliced on this mode.
For DS fi ber. MFD of DS fi ber is about 7 — 9µm at 1550nm wavelength.
For NZDS fiber. MFD of NZDS fiber is about 9~10 µm at 1550 nm
For MM fi ber. The core diameter of MM fi ber is about 50 — 62.5µm.
wavelength. WDM fiber can also be spliced on this mode.
Other splice modes are saved in the KF4 database; New splice modes are currently being updated;
Users should upgrade equipment regularly by contacting UCLSWIFT.
For DS fiber. MFD of DS fiber is about 7~9 µm at 1550 nm wavelength.
For MM fiber. The core diameter of MM fiber is about 50~62.5 µm.
Other splice modes are saved in the KF4 database.
New splice modes are currently being updated.
DESCRIPTION
Press and hold about 1 second to turn the power on/off.
Move the cursor to the left.
Move fiber to manual mode and adjust the camera's focus.
Stripping popup menu should load.
Move the cursor to the right.
Move fiber to manual mode and adjust the camera's focus.
Move the cursor upward.
button. It
Move each motor to manual mode.
Splice popup menu should load.
Move the cursor downward.
Move each motor to manual mode.
Heater popup menu should load.
Initialize the splice function.
Return to the menu screen.
button. It displays a screen for splice
Complete a selection.
Follow the next step on the menu screen.
Splice execution.
Return to the initial screen and initialize splice function.
Turn on the heater.
When it is on, the lamp on the left is in the red.
Press once more when it is on, and the heater is turned off.
9
22
Advertisement
Table of Contents
