Crivit 14129 - LED Bike Light Set Manual

Table of Contents

Contents

1 List of pictograms used
2 Introduction
3 Safety instructions
4 Safety advice concerning batteries/rechargeable batteries
5 Installation
6 Operation
- 6.1 Switching on / off
- 6.2 Charging the headlight
7 Cleaning and Care
8 Disposal
9 Documents / Resources
- 9.1 References
- 9.2 Download manual

List of pictograms used
	Read the instructions!
	to life and risk of accident for infants and children!
	Observe the warnings and safety notices!
	Explosion hazard!
	Green Dot - Packaging recycling.
	Symbol identifying electrical and electronic devices.
	Environmental damage through incorrect disposal of the batteries/ rechargeable batteries!
	USB – Universal Serial Bus – Connection port, e.g. on a computer (charging only).
	Federal Motor Transport Authority test symbol (K followed by approval number).
	Product and packaging should be disposed in an environmentally friendly manner.
	Recycling code for cardboard disposal.

Introduction

In doing so you have chosen a top-quality product. The instructions for use are to be considered as part of this product. It contains important safety, assembly and disposal information. Before using the product, please familiarise yourself with all the safety information and instructions for use. The product must only be used as described and for the specified fields of application. If you pass the product on to anyone else, please be sure to also include all documentation.

Intended use

This product is suitable for lighting the roadway whilst cycling. The LED Bicycle Light Set is approved as exclusive lighting for all bicycles. Light distribution must not be impaired by other bicycle parts or luggage. The product is intended for outdoor use. Any use other than the aforementioned or any product modification is prohibited and can result in injuries and product damage. The manufacturer is not liable for damages resulting from improper use. This product is not intended for commercial use.

Parts Description

Parts Description - Part 1
Parts Description - Part 2

Headlight bracket
Reducer rubber
Headlight bracket retaining screw
Headlight on/off switch
Headlight battery/rechargeable battery control light
Headlight
Headlight angle adjustment screw
Headlight lock
Tail light bracket
Tail light lock
Tail light bracket rubber tab
Tail light on/off switch
Tail light battery control lamp
Tail light
Tail light retaining screw
Tail light battery cover
USB cable
Charging socket

Scope of delivery

1 Headlight
1 Tail light
1 Headlight bracket
1 Tail light bracket
2 Batteries AAA
Reducer rubbers
1 USB cable
1 Instructions for assembly and use

Technical Data

Headlight
Model designation: XC-195A / LI-1
Rated output: 1 W
Protection type: I P44 according to DIN EN 60529
Rechargeable Li-ion battery: 1300 mAh, 3.7 V

Tail light
Model designation: XC-117D / D-LED 3
Rated output: 0.2W
Protection type: IP44 according to DIN EN 60529
Batteries: 2 x 1.5 V AAA LR03

Note: Only use rechargeable 1.2 V batteries or comparable 1.5 V alkaline batteries for the rear light.

Safety instructions

DANGER TO LIFE AND RISK OF ACCIDENT FOR INFANTS AND CHILDREN!
Never leave children unsupervised with the packing material due to the suffocation hazard posed by swallowing parts thereof. Children frequently underestimate the dangers.
Always keep the product away from children. This product is not a toy!
This product is not intended to be used by persons (including children) with impaired physical, sensory or mental capacity, or lacking experience or knowledge unless supervised by a person responsible for their safety. Please note, damages caused by incorrect handling, non-compliance with the operating instructions or interference with the device by unauthorised individuals are excluded.
Never take the product apart. Improper repairs may result in considerable danger to the user. Repairs should only be carried out by specialist personnel. The LED lights are not replaceable.
RISK OF LOSS OF LIFE AND ACCIDENT!
Using the incorrect charger may cause the headlight to be damaged, overheat or even explode. Doing so will void the warranty.

Safety advice concerning batteries/rechargeable batteries

EXPLOSION HAZARD! Never recharge the batteries!
Remove batteries during extended periods of non-use.
When inserting the battery ensure the polarity is correct! This is shown in the battery compartment.
If necessary, clean the battery and device contacts before inserting the battery.
Remove spent batteries immediately from the device. There is an increased risk of leaks!
Always replace all the batteries at the same time.
Do not mix alkaline batteries and rechargeable batteries.
Never mix old and new batteries.
Do not dispose of battery/rechargeable batteries in household waste!
Every consumer is legally obliged to dispose of batteries/rechargeable batteries in the proper manner!
EXPLOSION HAZARD!
Keep battery/rechargeable batteries away from children, do not throw batteries/rechargeable batteries into fire, do not short- circuit and do not take apart.
Failure to observe this notice may result in deep discharging the batteries. This poses a risk of leaking.
If the batteries have leaked inside the product, please remove them immediately to prevent product damage!
Avoid contact with the skin, eyes and mucous membranes if fluid has leaked from the batteries / rechargeable battery. In the event of contact with battery acid, thoroughly flush the affected area with clean water and seek immediate medical attention.
Never recharge single-use batteries! Explosion hazard!
Note: If the red rechargeable battery/battery control light on the headlight or the tail light lights up, please replace the batteries or recharge the rechargeable batteries immediately.
Please note, once the battery indicator lights up, the lights no longer comply with the Road Traffic Act.

Installation

Installing the headlight

(see Fig. A)

Unscrew the retaining screw from the bracket .
Position the bracket in the desired location on the handlebar. If necessary, use the reducer rubbers to ensure an optimal fit.
Reinstall the retaining screw .
Tighten the screw hand tight. To prevent damage, do not use tools for this step.
To adjust to the optimal angle to the direction of travel, loosen the angle adjustment screw 2–3 turns using a cross-tip screwdriver.
Adjust to the desired angle and tighten the angle adjustment screw .
Slide the headlight into the bracket until you hear it lock into place.
To release, press the headlight lock and slide the headlight forward out of the bracket .
ATTENTION! Routinely verify the headlamp adjustment. The light cone must point straight ahead, in the direction of travel, and must not be adjusted too high so as not to blind oncoming traffic.

Installing the tail light

(see Fig. B and C)

Secure the bracket to the seat post or the rear cross-bar using the rubber tab . Be sure there are no objects in front of the tail light .
Tighten and hook in the rubber tab .
Loosen the retaining screw on the bracket and adjust to the desired angle.
Then tighten the screw. Tighten the screw hand tight. To prevent damage, do not use tools for this step.
Slide the tail light into the bracket until you hear it lock into place.
To release the tail light , pull down on the tail light lock and slide off the tail light .
ATTENTION! The tail lamp must be installed and adjusted so the reference axis is parallel to the median longitudinal plane of the vehicle and parallel to the road.

Inserting batteries into the tail light

(see Fig. D)

Slide the battery cover off to the back.
Insert the batteries into the tail light (2 x AAA 1.5 V). Ensure the correct polarity.
Then reassemble the light.

Operation

Switching on / off

The headlight has three brightnesses.

On/Off switch
press once	Power mode (40 Lux) for riding in unlit areas
press twice	Standard mode (20 Lux) for riding in lit areas
press three times	Eco mode (10 Lux) for riding in well lit areas
press four times	off

Charging the headlight

(see Fig. E)

Remove the rubber cover from the battery charging socket and connect the USB cable to the battery charging socket .
Then connect the USB plug of the USB cable to a computer/laptop/standard USB charger with 5 V DC and 500–1000 mA. Using chargers with different specifications can damage the rechargeable battery, thus the headlight. Doing so will void the warranty.
The headlight has a battery indicator. If the indicator lights up red, the rechargeable batteries are drained. The indicator will light up green whilst charging. When the rechargeable batteries are ready to be used again, the indicator will extinguish and you can use the headlight .
For the included rechargeable batteries to operate at full power, please do not charge the battery for less than 10 hours the first time. Please do not stop charging sooner, even if the LED is already extinguished. After this, a charging time of approx. 3.5 hours is recommended for rechargeable batteries with 1300 mAh.

Cleaning and Care

Never fully immerse the lights. Do not use corrosive or abrasive cleaning agents. Doing so will damage the lights.
Clean the LED bicycle light set with a slightly damp, lint-free cloth.

Disposal

The packaging is made of environmentally friendly materials, which may be disposed of through your local recycling facilities.
Contact your local refuse disposal authority for more details on how to dispose of your worn-out product.

To help protect the environment, please dispose of the product properly, not without household waste, when it has reached the end of its useful life. Please contact your local authority for information on collection points and their opening hours.
Defective or used batteries/rechargeable batteries must be recycled according to 2006 / 66 / EC and its amendments. Return batteries/rechargeable batteries and / or the appliance using the recycling facilities provided.

Environmental damage due to incorrect battery/rechargeable battery disposal!
Never dispose of batteries/rechargeable batteries in your household waste. They may contain toxic heavy metals and are subject to hazardous waste regulations. The chemical symbols of the heavy metals are: Cd = cadmium, Hg = mercury, Pb = lead. Therefore, dispose of used batteries/rechargeable batteries through your local collection site.
Improper battery disposal destroys valuable resources and the hazardous substances in the batteries may pose a significant danger to the health and environment. Separate collection/disposal of old batteries prevents dangers to the health and environment, and valuable resources regained by recycling.