Gree SAPPHIRE SAP12HP230V1AH Installation, Service & Troubleshooting page 21

(2) Under the initial presetting temperature17
after 1 decreased, this temperature will be maintained.
(3) Under the initial presetting temperature 21 -27
in every hour, after 2
(4) Under the initial presetting temperature 28
decreased, this temperature will be maintained.
Sleep 3 - the sleep curve setting under Sleep mode by DIY:
(1) Under Sleep 3 mode, press "Turbo" button for a long time, remote controller en-
at this time, the time of remote
last setting sleep curve and blink (The first entering
(2) Adjust "+" and "-" button, could change the corresponding setting temperature,
(3) At this time, 1hour will be automatically increased at the timer postion on the
"8hours"), the place of se-
(4) Repeat the above step (2)~(3) operation, until 8hours temperature setting finished,
controller will resume the
Sleep3 - the sleep curve setting under Sleep mode by DIY could be inquired:
The user could accord to sleep curve setting method to inquire the presetting sleep
status, but do not change the tem-
Note: In the above presetting or enquiry procedure, if continuously within10s, there
will be automatically quit
"Mode" button, "Timer" button or "Sleep"
Introduction for special function
About AUTO RUN
When AUTO RUN mode is selected, the unit will be in accordance with the room temp.
automatically to select the suitable running method and to make ambient comfortable.
About turbo function
If start this function, the unit will run at super-high fan speed to cool or heat quickly so
approachs the preset temp. as soon as possible.
About lock
Press + and - buttons simultaneously to lock or unlock the keyboard. If the remote co-
in which case, press any button,
About swing up and down
1. Press swing up and down button continuously more than 2s, the m ain unit will swing
the button, the unit will stop swing
2. Under swing up and down mode, when the status is switched from off to
status directly; If press this button
About swing left and right
1. Press swing left and right button continuously more than 2s, the main unit will swing
button, the unit will stop swing
2. Under swing left and right mode, when the status is switched from off to
status directly; if press this button
About switch between Fahrenheit and Centigrade
Under status of unit off, press MODE and - buttons simultaneously to switch
Combination of "TEMP" and "CLOCK" buttons:
About Energy - saving Function
Press "TEMP" and "CLOCK" simultaneously in COOL mode to start energy-saving fun-
"SE". Repeat the operation to quit
Combination of "TEMP" and "CLOCK" buttons:
About 8 Heating Function
Press "TEMP" and "CLOCK" simultaneously in HEAT mode to start 8
Nixie tube on the remote controller displays "
(46 if Fahrenheit is adopted). Repeat the operation to quit the function.
18
-20
decreased, this temperature will be maintained.
-30
controller will display "1hour", the setting temperature "88" will display the corr-
tting temperature "88" will display the corresponding temperature of last setting sleep curve and blink;
original timer display; temperature display will resume to original setting tem- perature.
perature, press "Turbo" button directly for confirmation.
and resume to display the original displaying. In the presetting or enquiry pr-
button, the sleep curve setting or enquiry status will quit similarly.
the mark will flicker for three times. If the keyboard is unlocked, the mark will disappear.
and present position of guide louver will be kept immediately.
again within 2s, the change of swing status will also depend on the circulation seque-
and present position of guide louver will be kept immediately.
again within 2s, the change of swing status will also depend on the circulation sequ-ence stated above.
the function.
" and a sele cted temperature of "8
, after Sleep function started
, after Sleep function started
, after Sleep function started
will display according to the initial curve setting value of original factory);
remote controller, (that are "2hours" or "3hours" or
, if press
, if press
and
Heating Function
up, the temperature will decrease 1
up, the temperature will decrease 1
up, the temperature will decrease 1
ters into user individuation sleep setting status,
after adjusted, press "Trubo" button for confirmation;
sleep curve setting finished, at this time, the remote
curve, enter into user individuation sleep setting
is no button pressed, the sleep curve setting status
ocedure, press "ON/OFF" button,
that the ambient temp. approachs the preset temp.
ntroller is locked, the icon
backand forth from up to down , and then loosen
this button again 2s later,
back and forth from left to right, and then loosen the
this button again 2s later,
.
ction. Nixie tube on the remote controller displays
".
Service Manual
in every hour,
in every hour, after 3
esponding temperature of
will be displayed on it,
status will switch to off
nce stated above.
status will switch to off
Technical Information