Related Manuals for Meinberg LANTIME M200/GPS/RPS
Summary of Contents for Meinberg LANTIME M200/GPS/RPS
- Page 1 TECHNICAL REFERENCE LANTIME M200/GPS/RPS NTP Time Server with GPS Receiver October 26, 2022 Meinberg Funkuhren GmbH & Co. KG...
-
Page 3: Table Of Contents
Installation and Grounding ........9 RoHS and WEEE 10 Declaration of Conformity Date: October 26, 2022 LANTIME M200/GPS/RPS... -
Page 4: Imprint
1 Imprint 1 Imprint Meinberg Funkuhren GmbH & Co. KG Lange Wand 9, 31812 Bad Pyrmont, Germany Phone: + 49 (0) 52 81 / 93 09 - 0 Fax: + 49 (0) 52 81 / 93 09 - 230 Website: https://www.meinbergglobal.com Email: info@meinberg.de... -
Page 5: Important Safety Information
ATTENTION! This signal word refers to a procedure or other action that may result in product damage or the loss of important data if not observed or if improperly performed. Date: October 26, 2022 LANTIME M200/GPS/RPS... -
Page 6: Used Symbols
Dieses Produkt fällt unter die B2B Kategorie. Zur Entsorgung muss es an den Hersteller übergeben werden. This product is handled as a B2B-category product. To ensure that the product is disposed of in a WEEE-compliant fashion, it must be returned to the manufacturer. LANTIME M200/GPS/RPS Date: October 26, 2022... -
Page 7: Product Documentation
2.3 Product Documentation Detailed product documentation is provided on a USB flash drive delivered with the Meinberg system. The manuals can also be downloaded from the Meinberg website at https://www.meinbergglobal.com, where you can enter your system name into the search box at the top of the page to find the relevant manual. Alternatively, contact Meinberg Support for further assistance. -
Page 8: Safety During Installation
For safety reasons, the device with the highest mass should be installed at the lowest position in the rack. Further devices should be installed from the bottom, working your way up. The device must be protected against mechanical & physical stresses such as vibration or shock. LANTIME M200/GPS/RPS Date: October 26, 2022... - Page 9 = 90 - 250 V Faulty shielding or cabling and improperly connected plugs are a health & safety risk (risk of injury or death due to electrical shock) and may damage or even destroy your Meinberg device or other equipment.
- Page 10 LANTIME M200/GPS/RPS Date: October 26, 2022...
-
Page 11: Connection Of Protective Earth Conductor/Grounding
A grounding cable is not included in the contents of delivery. Note: Please use a grounding cable with cross-section 1.5 mm , as well as a suitable grounding clamp/lug. Always ensure that the connection is properly crimped! Date: October 26, 2022 LANTIME M200/GPS/RPS... -
Page 12: Safety During Operation
If your device is connected to an Uninterruptible Power Supply (UPS), it will remain operational even after pulling the UPS power cable from the mains socket. In this case, you will need to shut down your UPS in accordance with the user documentation of your UPS system. LANTIME M200/GPS/RPS Date: October 26, 2022... -
Page 13: Safety During Maintenance
Opening the device or individual device components in an unauthorized fashion may also expose the user to considerable risks and invalidate your warranty. Meinberg Funkuhren accepts no liability for consequences arising from such unauthorized actions. Danger from moving parts—do not touch moving parts. -
Page 14: Handling Of Batteries
The battery is used to power components such as the RAM and the reserve real-time backup clock for the reference clock. If the battery voltage drops below 3 V DC, Meinberg recommends having the battery replaced. If the battery voltage drops below the specified minimum, the following behavior may be... -
Page 15: Cleaning And Care
ESD-proof bags that are crumpled or have holes cannot provide effective protection against electrostatic discharges. ESD-proof bags must have a sufficient electrical resistance and must not be made of conductive metals if the device has a lithium battery fitted on it. Date: October 26, 2022 LANTIME M200/GPS/RPS... -
Page 16: Return Of Electrical And Electronic Equipment
When disposing of your old equipment, please use the national return or collection systems available to you. Alternatively, you may contact Meinberg, who will provide further assistance. The return of electronic waste may not be accepted if the device is soiled or contaminated in such a way that it potentially presents a risk to human health or safety. -
Page 17: General Information About Lantime
LANTIME via any standard web browser. LANTIME M100 time servers do not have a display or function keys. Instead, these systems are configured and monitored via the LANTIME Web Interface, SSH, Telnet, or FTP. Date: October 26, 2022 LANTIME M200/GPS/RPS... -
Page 18: Lantime Chassis: Technical Specifications
-20–70 C (-4–158 F) ——————————————————————————- Relative Humidity Operation: Max. 85 % (Non-Condensing) at 30 C ——————————————————————————- Maximum Altitude Operation: Max. 4000 m / 13123 ft (Above Sea Level) ——————————————————————————- Acoustics: 0 dB (A) IP Rating: IP20 LANTIME M200/GPS/RPS Date: October 26, 2022... - Page 19 This terminal must be wired to a bonding busbar (grounding busbar). The terminal is located on the side of the chassis with the power supply unit. The parts required to establish this connection—not including the grounding conductor cable itself—are included with the product as shipped. Date: October 26, 2022 LANTIME M200/GPS/RPS...
-
Page 20: Lantime M200 Front Connectors
By using the 4 arrows and the "ESC", "F1" and "F2" buttons of the keypad you can navigate through each menu in the display. You can always return to the main menu by pressing the "ESC" button several times. LANTIME M200/GPS/RPS Date: October 26, 2022... - Page 21 NTP is not synchronized or switched to the "local clock" "Network" green: all monitored network interfaces are connected ("Link up") red: at least one of the monitored network interfaces is faulty "Alarm" off: no error red: general error Date: October 26, 2022 LANTIME M200/GPS/RPS...
-
Page 22: Lantime M200 Rear Connectors
6 LANTIME M200 Rear Connectors 6 LANTIME M200 Rear Connectors Information: The numbering in the drawing above relates to the relevant subsection in this chapter. LANTIME M200/GPS/RPS Date: October 26, 2022... -
Page 23: Ac/Dc - Power Supply
• All connectors must provide protection against contact with live parts in the form of a suitable plug body! • Always ensure that wiring is safe! • The device must be grounded by means of a connection with a correctly installed protective earth conductor (PE). Date: October 26, 2022 LANTIME M200/GPS/RPS... -
Page 24: 10/100Base-T Network Port (Ieee 803.2)
• locking the keys on the LC display to prevent unauthorized access • backing up the LANTIME configuration • transferring configurations between individual LANTIMES • copying log files • installing firmware updates • uploading and downloading secure certificates (SSL, SSH) and passwords LANTIME M200/GPS/RPS Date: October 26, 2022... -
Page 25: Terminal
NTP is not synchronized or has switched to the "local clock" "Ref. Time" Green: A valid time is provided by the reference clock (e.g., integrated GPS) Red: There is no valid time available from the reference clock Date: October 26, 2022 LANTIME M200/GPS/RPS... -
Page 26: Antenna Input: Gps Reference Clock
• Do not carry out any work on the antenna system or the antenna cable if there is a risk of lightning strike. • Do not carry out any work on the antenna system if it is not possible to maintain the prescribed safe distance to exposed lines and electrical substations. LANTIME M200/GPS/RPS Date: October 26, 2022... -
Page 27: Leds Gps Receiver
No synchronization, no antenna connected, Ant. or short circuit on the antenna line Nav. Green: Antenna is connected and clock is synchronized Init. Green: Positioning complete Init Blue: Initialisation phase Green: Oscillator is disciplined ("warmed up") Date: October 26, 2022 LANTIME M200/GPS/RPS... -
Page 28: Installation Of A Gps Antenna
• clear view between 55th north and 55th south parallels (satellite orbits). Information: Problems may arise if all of these views are obstructed, as four satellites must be located to calculate a new position. LANTIME M200/GPS/RPS Date: October 26, 2022... - Page 29 Case Example 4: If the cable leading from the point of entry into the building to the Meinberg system is laid together with other cables (for example in a cable duct alongside high-voltage cables), transient voltages may "leak" into the antenna cable, causing damage to your system.
- Page 30 Type-N (Male) If installed in a waterproof housing, the MBG S- Type-N (Female) PRO can be installed outdoors. However, Meinberg recommends installing the surge protector indoors—as closely to the entrance point of the antenna cable as possible—in order to minimize the risk of surge dam- age (such as that caused by lightning strike).
- Page 31 The next step is to connect the supplied coaxial cable from the surge protector to the receiver. Type-N (Female) Type-N (Male) Receiver Optional Antenna Splitter SMA (Male) SMA (Female) BNC (Male) BNC (Female) Type-N (Male) Type-N (Female) Date: October 26, 2022 LANTIME M200/GPS/RPS...
- Page 32 The splitter may be installed at any location between the surge protector and the receivers. Information: Please note for installation purposes that GNSS L1 components cannot be directly connected to or used with a Meinberg GPS antenna distributor. Antenna Receiver Antenna Splitter...
-
Page 33: Technical Appendix: Gps Antenna + Accessories
8 Technical Appendix: GPS Antenna + Accessories Physical Dimensions: Date: October 26, 2022 LANTIME M200/GPS/RPS... - Page 34 Form Factor: ABS Plastic Case for Outdoor Installation IP Rating: IP66 Humidity: 95 % Temperature Range: -60 C to +80 C (-76 F to 176 F) Weight: 1.6 kg (3.53 lbs), including mounting kit LANTIME M200/GPS/RPS Date: October 26, 2022...
-
Page 35: Technical Specifications: Antenna Cable
8.1 Technical Specifications: Antenna Cable The table below shows which coaxial cable types and lengths are supported by Meinberg for each of the receiver types. If you need to purchase a replacement cable at any time, please refer to this table to ensure that you select cable with suitable cutoff... -
Page 36: Technical Specifications: Mbg S-Pro Surge Protector
5 A (25 C) Effective Operating Current: IC at UC Rated Discharge Current: In (8/20) s (Core-Earth) 20 kA In (8/20) s (Core-Shield) 20 kA Total Surge Current: (8/20) s 20 kA (10/350) s 2.5 kA LANTIME M200/GPS/RPS Date: October 26, 2022... - Page 37 The original product page of the supplier (see link) of the CN-UB-280DC-BB surge protector is the source of the specifications above. Please refer to the manufacturer’s product page at the following link for detailed specifications as well as a variety of product-specific documents: https://www.phoenixcontact.com/online/portal/gb/?uri=pxc-oc-itemdetail:pid=2818850 Date: October 26, 2022 LANTIME M200/GPS/RPS...
-
Page 38: Mbg S-Pro: Physical Dimensions
8 Technical Appendix: GPS Antenna + Accessories 8.3.1 MBG S-PRO: Physical Dimensions 15,8 8.3.2 Installation and Grounding LANTIME M200/GPS/RPS Date: October 26, 2022... -
Page 39: Rohs And Weee
WEEE-compliant fashion, it can be returned to the manufacturer. Any transportation ex- penses for returning this product (at end-of-life) must be covered by the end user, while Meinberg will bear the costs for the waste disposal itself. Date: October 26, 2022... -
Page 40: Declaration Of Conformity
10 Declaration of Conformity 10 Declaration of Conformity Declaration of Conformity Doc ID: LANTIME M200/GPS/RPS-October 26, 2022 Hersteller Meinberg Funkuhren GmbH & Co. KG Manufacturer Lange Wand 9, D-31812 Bad Pyrmont erklärt in alleiniger Verantwortung, dass das Produkt, declares under its sole responsibility, that the product...