Related Manuals for K-array Kommander-KA02 I
Summary of Contents for K-array Kommander-KA02 I
- Page 1 USER GUIDE Kommander-KA02 I Aluminum 200W compact amplifier and processing solution •20230124•...
- Page 2 Kommander-KA02 I User Guide This page intentionally left blank...
- Page 3 Kommander-KA02 I User Guide IMPORTANT SAFETY INSTRUCTIONS General heed and warnings • Read these instructions. • Keep these instructions. • Heed all warnings. • Follow all instructions. • Do not use this apparatus near water. • Clean only with dry cloth.
- Page 4 • this device may not cause interference, and amplifier’s rated range can damage the apparatus. • this device must accept any interference, including interference that may cause • K-array cannot be held responsible for damage caused by improper use of the undesired operation of the device. loudspeakers.
-
Page 5: Table Of Contents
Kommander-KA02 I User Guide Sommario Unpacking Dashboard Kommander-KA02 I Rear Panel USB Media Player Bluetooth Media Player Software Webradio Media Player Introduction DanteReady™ streamer Getting Started Device preset Mounting and cooling Audio Configuration AC MAINS supply Output Configuration LED chart... - Page 6 Kommander-KA02 I User Guide This page intentionally left blank...
- Page 7 K-array distributor in your country. The Kommander-KA02 I is a fully featured 4x 50W @ 4Ω class-D amplifier with a high-performing DSP. The digital processing multi-channel amplifier is designed for optimized performance in small to medium loudspeaker systems.
-
Page 8: Unpacking
User Guide Unpacking Kommander-KA02 I Rear Panel Each K-array amplifier is built to the highest standard and thoroughly inspected before leaving the factory. Upon arrival, carefully inspect the shipping carton, then examine and test your new amplifier. If you find any damage, immediately notify the shipping company. -
Page 9: Introduction
219 x 46 x 170 mm (8.6 x 1.8 x 6.7 in). 2. Connect the Kommander-KA02 I to its power supply and plug the power cord to the AC mains socket. With the backing of 200W, the Kommander-KA02 I amplifier 3. -
Page 10: Mounting And Cooling
User Guide Mounting and cooling AC MAINS supply The Kommander-KA02 I amplifier and processing unit can be set The Kommander-KA02 I amplifier unit is provided with a stand alone or installed into rack cabinets with the K-RACK24 dedicated 24 VDC LPS power supply, suiting any nominal input rack-mounting hardware accessory. -
Page 11: Input Wiring
User Guide Input wiring Loudspeaker wiring Audio signals can be fed to the Kommander-KA02 I amplifier unit A minimum set of Euroblock flying connectors is provided in the using the input connectors on the rear panel. package for connecting the loudspeakers to the amplifier unit. -
Page 12: K-Remuctrl Remote
K-REMUCTRL is the optional wireless remote dedicated to nominal impedance according to the cable run. control the Kommander-KA02 I amplifier unit In order to use the K-REMUCTRL with the Kommander-KA02 I Leveraging on the K-array loudspeaker impedance, the amplifier: Kommander-KA02 I output channels can be connected to 1. -
Page 13: Remote Connectivity
DHCP server managing the addresses allocation: The integrated operating system osKar features a complete by default the Kommander-KA02 I unit is set to obtain a local IP web user interface accessible over the network: connect to the address from the DHCP server. -
Page 14: K-Array Connect Mobile App
3. If the list of available devices is empty touch the SCAN QR CODE button and use the mobile device camera to frame the QR code in the bottom panel of the Kommander-KA02 I Main menu unit: this provides the mobile device to connect to the amplifier’s hot spot. -
Page 15: Embedded Web App
The web app is accessible via a web browser (Google Chrome recommended) over a wired or wireless connection to the amplifier unit. The K-array Connect Mobile App and the K-framework3 software interfaces include a shortcut for opening the web app, once... -
Page 16: Audio Configuration
Note 5. If needed, set the number of loudspeakers that are * The output configuration of the Kommander-KA02 I included in an Azimut system connected in parallel to the amplifier output connector. bundle is factory pre-configured. -
Page 17: Matrix
Kommander-KA02 I User Guide MATRIX 7. Apply the output channel configuration. 8. If needed set the proper pairing channels in PBTL mode. The matrix allows to set the signal routing path between the 9. Go to the Routing section and set the proper signal routng four amplifier’s input channels and the four amplifier’s output... -
Page 18: Network
USB key. Update via Internet WiFi 1. Connect the Kommander-KA02 I amplifier unit to Internet – The WiFi can be configured to connect the unit to a wireless possibly via a wired connection. LAN as a CLIENT or, alternatively, to create an independent local 2. - Page 19 Kommander-KA02 I User Guide B. Open the K-array website on the Internet browser on your PC or Mac. C. Navigate the Products->Software menu and scroll down to the Download section of the Software webpage. D. Download the osKar System (ensure to be registered to the website in order to proceed with the download) and save the update file with extension .mender into the...
-
Page 20: K-Framework3
User Guide K-framework3 The K-framework3 can work either off-line with virtual devices or The Kommander-KA02 I unit can be remotely controlled with the on-line with real active loudspeakers and amplifiers connected dedicated K-framework3 software available for PC and MAC on over the same Ethernet network. -
Page 21: Discovery
ID, a dialog window appears where unique IDs can to default the EQ, delay and volume parameters be assigned to the units. edited with the K-array Control mobile app and the embedded Web app. A. In Setup mode, set the Kommander-KA local parameters (presets, routing, input gains, limiters, etc). -
Page 22: Mechanical Drawing
Kommander-KA02 I User Guide Mechanical Drawing 109mm 4,3in 109mm 4,3in 219mm 170mm 8,6in 6,7in 219mm 170mm 8,6in 6,7in... -
Page 23: Specifications
Wi-Fi IEEE 802.11 b/g/n Grouping, Input EQ, Output EQ, Signal Routing, Level Built-in DSP adjustment, Dynamic Limiters, Delay Wi-Fi dedicated K-array Connect mobile app Remote control Ethernet wired K-framework3 multiplatform design and tuning software Dedicated AC/DC power adapter 100-240V ~ AC, 50-... - Page 24 Designed and Made in Italy K-ARRAY surl Via P. Romagnoli 17 | 50038 Scarperia e San Piero - Firenze - Italy ph +39 055 84 87 222 | info@k-array.com www.k-array.com...
Need help?
Do you have a question about the Kommander-KA02 I and is the answer not in the manual?
Questions and answers