AJAX FireProtect Instruction Manual page 2

5.7 Fix SmartBracket fastening panel in the ceiling using supplied dowels and
screws.
5.7 Fix SmartBracket fastening panel in the ceiling using supplied dowels and 5.8 Fix detector on SmartBracket. Once the detector is fixed on SmartBracket,
it must blink with green LED - it means that tamper button is closed on the
screws.
detector. If detector didn't blink, you should check lid state in receiver settings.
5.8 Fix detector on SmartBracket. Once the detector is fixed on SmartBracket,
it must blink with green LED - it means that tamper button is closed on the
detector. If detector didn't blink, you should check lid state in receiver settings.
PICTURE 2.
SmartBracket fastening panel
PICTURE 2.
SmartBracket fastening panel
IMPORTANT!
Be careful when installing the fastening panel. Excessive force during its
IMPORTANT!
fixation may lead to deformation and, as a consequence, in impossibility to
Be careful when installing the fastening panel. Excessive force during its install the detector or insecure fixing. Secure fastening panel only using with
supplied mounting tools! Use of other fasteners, such as, large diameter
fixation may lead to deformation and, as a consequence, in impossibility to
screws, may damage the fastening panel.
install the detector or insecure fixing. Secure fastening panel only using with
supplied mounting tools! Use of other fasteners, such as, large diameter
screws, may damage the fastening panel.
5.9 The detector is installed!
5.10 Ensure that elements of interior, furniture, curtains, house plants,
decorative design, wires or other objects don't cover detector.
5.9 The detector is installed!
5.10 Ensure that elements of interior, furniture, curtains, house plants,
decorative design, wires or other objects don't cover detector.
IMPORTANT!
Don't install the detector:
IMPORTANT!
• near the points places of fast air circulation (ventilations units, open
windows or doors);
Don't install the detector:
• near metal objects, causing radio signal attenuation;
• near the points places of fast air circulation (ventilations units, open
• In the rooms with temperature and humidity exceeding the appropriate windows or doors);
levels.
• near metal objects, causing radio signal attenuation;
• In the rooms with temperature and humidity exceeding the appropriate
levels.
5.11 Before installation be sure to run a test to check smoke detector
operability. When the detector is switched on and in work mode (without
5.11 Before installation be sure to run a test to check smoke detector alarm) put finger on the touch-sensitive button «Test» on the detector's body
in the center of AJAX logo («1», PICTURE 1) for up to 10 seconds. It will switch
operability. When the detector is switched on and in work mode (without
the detector to self-test mode for about 5 seconds. In self-test mode, smoke
alarm) put finger on the touch-sensitive button «Test» on the detector's body
in the center of AJAX logo («1», PICTURE 1) for up to 10 seconds. It will switch chamber operability is checked, electronic simulation of smoke presence is
made, and if smoke chamber is OK – sound signal is generated.
the detector to self-test mode for about 5 seconds. In self-test mode, smoke
chamber operability is checked, electronic simulation of smoke presence is
made, and if smoke chamber is OK – sound signal is generated.
2
9
1
2
10
9
1
2
10
3
2 4
7
3
4
7
8
8
2
2
PICTURE 3. Detector
construction.
PICTURE 3. Detector
construction.
1 – body opening tamper button
2 – smoke chamber apertures
3 – «Test» button
1 – body opening tamper button
4 – «Chamber is dirty» signal reset
2 – smoke chamber apertures
3 – «Test» button button
4 – «Chamber is dirty» signal reset 5 – siren
6 – antenna
button
5 – siren
www.solar.dk
6 – antenna
Be careful when installing the fastening panel. Excessive force during its
fixation may lead to deformation and, as a consequence, in impossibility to
install the detector or insecure fixing. Secure fastening panel only using with
supplied mounting tools! Use of other fasteners, such as, large diameter
screws, may damage the fastening panel.
5.9 The detector is installed!
5.10 Ensure that elements of interior, furniture, curtains, house plants,
decorative design, wires or other objects don't cover detector.
Don't install the detector:
• near the points places of fast air circulation (ventilations units, open
• near metal objects, causing radio signal attenuation;
• In the rooms with temperature and humidity exceeding the appropriate
5.11 Before installation be sure to run a test to check smoke detector
operability. When the detector is switched on and in work mode (without
alarm) put finger on the touch-sensitive button «Test» on the detector's body
in the center of AJAX logo («1», PICTURE 1) for up to 10 seconds. It will switch
the detector to self-test mode for about 5 seconds. In self-test mode, smoke
chamber operability is checked, electronic simulation of smoke presence is
made, and if smoke chamber is OK – sound signal is generated.
6
5
6
2
5
2
11
11
1 – body opening tamper button
2 – smoke chamber apertures
3 – «Test» button
4 – «Chamber is dirty» signal reset
5 – siren
6 – antenna
7 – smoke chamber
8 – CR2 batteries
9 – backup battery CR2032
7 – smoke chamber
10 – Carbon monoxide detector (only
8 – CR2 batteries
9 – backup battery CR2032 in FireProtectPlus)
11 – smoke chamber latches 10 – Carbon monoxide detector (only
in FireProtectPlus)
11 – smoke chamber latches
6. MAINTENANCE
6.1 Maintenance is done once every 6 months. The sensor's board must be
6. MAINTENANCE
cleared of dust, spider web and other impurities.
6.2 If to much dust entered the smoke chamber it can be perceived as smoke,
6.1 Maintenance is done once every 6 months. The sensor's board must be
and detector can give a false alarm. Regularly, at least once in 6 months, get cleared of dust, spider web and other impurities.
rid of the dust, cleaning detector smoke chamber. If detector is installed in a
6.2 If to much dust entered the smoke chamber it can be perceived as smoke,
dusty premises, you need to clean it more often.
and detector can give a false alarm. Regularly, at least once in 6 months, get
6.3 Detector has the ability to compensate smoke chamber dustiness, but only rid of the dust, cleaning detector smoke chamber. If detector is installed in a
before certain level reach, above which the message on necessity to clean PICTURE 2.
dusty premises, you need to clean it more often.
smoke chamber is sent to the receiver (panel). In case of smoke chamber
6.3 Detector has the ability to compensate smoke chamber dustiness, but only SmartBracket fastening panel
failure the detector gives a long sound signal once a minute and a half! To clean before certain level reach, above which the message on necessity to clean
chamber remove the detector cover by unscrewing 4 screws «4» (PICTURE 1)
smoke chamber is sent to the receiver (panel). In case of smoke chamber
on the corners of detector body backside. Then remove touch-sensitive button
failure the detector gives a long sound signal once a minute and a half! To clean
board «3» (PICTURE 1) by pulling it up gently, then remove plastic nozzle, chamber remove the detector cover by unscrewing 4 screws «4» (PICTURE 1)
IMPORTANT!
covering the card. Then remove internal protective cover of smoke chamber on the corners of detector body backside. Then remove touch-sensitive button
block «7» (PICTURE 3) easily pressing on 2 of 3 retaining latches «11»
board «3» (PICTURE 1) by pulling it up gently, then remove plastic nozzle,
covering the card. Then remove internal protective cover of smoke chamber (PICTURE 3). Blow the removed block with vacuum cleaner, compressor or
block «7» (PICTURE 3) easily pressing on 2 of 3 retaining latches «11» clean it with a soft brush. Also remove dust from that part of smoke chamber,
which remained on the detector. After cleaning procedure end be sure to press
(PICTURE 3). Blow the removed block with vacuum cleaner, compressor or
on «Chamber is dirty» signal reset button «4» (PICTURE 3)!
clean it with a soft brush. Also remove dust from that part of smoke chamber,
After pressing the button, the detector gives one short sound signal! If this which remained on the detector. After cleaning procedure end be sure to press
button is not pressed, a signal on necessity to clean the detector will continue
on «Chamber is dirty» signal reset button «4» (PICTURE 3)!
to be sent to the receiver (panel). If chamber was not cleaned but «Chamber is
After pressing the button, the detector gives one short sound signal! If this
button is not pressed, a signal on necessity to clean the detector will continue dirty» signal reset button was pressed, a signal on smoke chamber excessive
contamination will come after 4 days again. In case of carbon monoxide (CO)
to be sent to the receiver (panel). If chamber was not cleaned but «Chamber is
detector failure, the detector similarly gives one long sound signal every
dirty» signal reset button was pressed, a signal on smoke chamber excessive
IMPORTANT!
minute and a half! contamination will come after 4 days again. In case of carbon monoxide (CO)
6.4 Never rub the sensor with substances containing alcohol, acetone, petrol
detector failure, the detector similarly gives one long sound signal every
and other solvents.
minute and a half!
windows or doors);
6.4 Never rub the sensor with substances containing alcohol, acetone, petrol 6.5 Replace the batteries up to date. If the battery level is low, the sensor sends
and other solvents. signal to the alarm system receiver unit. Detector also signals about low
battery with sound signals: one short sound signal - main batteries CR2 are
6.5 Replace the batteries up to date. If the battery level is low, the sensor sends
levels.
discharged; two short sound signals – backup CR2032 battery is discharged;
signal to the alarm system receiver unit. Detector also signals about low
battery with sound signals: one short sound signal - main batteries CR2 are three sound signals - both batteries are discharged.
To replace the batteries, switch off FireProtect with power button, unscrew
discharged; two short sound signals – backup CR2032 battery is discharged;
screws «4» (PICTURE 1) and remove detector cover. Detector has elements
three sound signals - both batteries are discharged.
To replace the batteries, switch off FireProtect with power button, unscrew that blocks cover assembly without installed the main set of batteries. Change
batteries with new ones, following polarity. Switch on FireProtect with power
screws «4» (PICTURE 1) and remove detector cover. Detector has elements
button.
that blocks cover assembly without installed the main set of batteries. Change
batteries with new ones, following polarity. Switch on FireProtect with power
button.
IMPORTANT!
Duration of detector autonomous operation depends on batteries quality
IMPORTANT!
and quantity of alarms triggered. At the average batteries works for about 4
years. It is not possible to switch on detector with backup battery only, main
Duration of detector autonomous operation depends on batteries quality
batteries must be always installed.
and quantity of alarms triggered. At the average batteries works for about 4
years. It is not possible to switch on detector with backup battery only, main
batteries must be always installed.
7. WARRANTY
2
7.1 The warranty period for the detector is 24 months. Warranty does not apply
9
7. WARRANTY
1 to the batteries!
10
7.1 The warranty period for the detector is 24 months. Warranty does not apply
to the batteries!
2
3
4
7
8
2
PICTURE 3. Detector
construction.
button
Разработчик и производитель НПП «Аякс», Украина, г. Киев, ул. Скляренко, 5,
Разработчик и производитель НПП «Аякс», Украина, г. Киев, ул. Скляренко, 5,
Solar Sikring
6
5
2
11
7 – smoke chamber
8 – CR2 batteries
9 – backup battery CR2032
10 – Carbon monoxide detector (only
in FireProtectPlus)
11 – smoke chamber latches
тел. +38 044 538 13 10, www.ajax.systems
тел. +38 044 538 13 10, www.ajax.systems
rid of the dust, c
dusty premises,
6.3 Detector has
before certain le
smoke chamber
failure the detect
chamber remove
on the corners of
board «3» (PICT
covering the card
block «7» (PICT
(PICTURE 3). Blo
clean it with a so
which remained
on «Chamber is
After pressing th
button is not pres
to be sent to the r
dirty» signal rese
contamination w
detector failure,
minute and a hal
6.4 Never rub th
and other solven
6.5 Replace the b
signal to the ala
battery with soun
discharged; two
three sound sign
To replace the b
screws «4» (PIC
that blocks cover
batteries with ne
button.
IMPORTANT
Duration of det
and quantity of
years. It is not p
batteries must
7. WARRANTY
7.1 The warranty
to the batteries!
Разработчи