Download
Share
Print this page
HermanMiller New Aeron Quick Start Manual
  1. Manuals
  2. Brands
  3. HermanMiller Manuals
  4. Indoor Furnishing
  5. New Aeron
  6. Quick start manual

HermanMiller New Aeron Quick Start Manual

Fixed arm casting replacement
Hide thumbs Also See for New Aeron:
1
2
3
4
5
6
7
8

Advertisement

Quick Links

Download this manual
Y
Parts Included:
Fixed Arm casting
Tools Required:
Ratchet Wrench
Steps:
1. Remove the back bolts
using 5mm Hex bit.
Z
© 2016 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Z, Aeron are among the registered trademarks of Herman Miller, Inc.
Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
TM
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
M5 Hex Bit
T27 Torx Bit
New Aeron
Fixed Arm casting Replacement
®
Fixed Arm Attachment
Hardware Assembly
Torque Wrench
2. Remove four bolts.
Fixed Arm Filler
T27 and T25 Torx Driver
Part no. 1BH1VV rev B.
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the New Aeron and is the answer not in the manual?

Questions and answers

Related Manuals for HermanMiller New Aeron

Summary of Contents for HermanMiller New Aeron

  • Page 1 New Aeron Fixed Arm casting Replacement ® Parts Included: Fixed Arm Attachment Fixed Arm Filler Fixed Arm casting Hardware Assembly Tools Required: T27 and T25 Torx Driver Ratchet Wrench M5 Hex Bit T27 Torx Bit Torque Wrench Steps: 1. Remove the back bolts 2.
  • Page 2 3. Detach the back from the 4. Remove the screw to chair. detach the arm pad. Use T25 Torx bit to remove the screw. 5. Lift the pad on the front and slide backwards as shown above to disengage it from the arm support.
  • Page 3 6. Detach the arm pad. 7. Remove the screws to detach the arm support hardware. 8. Use T27 Torx bit to re- move the screw. Part no. 1BH1VV rev B. © 2016 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A. ®...
  • Page 4 9. Detach the arm support 10. Fixed arm removal. hardware. 11. Remove the bolt from 12. Detach the bolt and filler. the swing arm using T27 torx driver. Part no. 1BH1VV rev B. © 2016 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A. ®...

  • Page 5: Re-Assembly Steps

    13. Arm filler an be de- tached. Re-Assembly Steps: 14. Replace the arm support 15. Tighten the screw to hardware in place on the attach the support hardware arm casting. to the arm casting. Use T27 Torx bit with torque 110 in- lbs.
  • Page 6 16. Slide the rear of the arm 17. Reinstall the new arm pad pocket over tab on arm pad to the arm support support. Rotate front of arm down into position. 18. Use T25 torx bit to install 19. Replacing fixed arm. the screw.
  • Page 7 20. Install the arm assembly 21. Assemble arm plate and into swing arm. bolt and attach to arm. 22. Install the bolt with 220 23. Follow previous steps to in-lbs torque using T27 torx- install left hand arm. bit. Part no. 1BH1VV rev B. ©...
  • Page 8 24. Install back assembly. 25. Install four back bolts using a torque wrench and a 5 mm hex bit. Torque each bolt to 150 in-lbs. Part no. 1BH1VV rev B. © 2016 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A. ®...