Table of Contents
Advertisement
Quick Links
Silver Pneumatic Arm TV Wall Mount
Instruction Manual
SKU: MOUNT-VW03G
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
https://vivo-us.com/products/mount-vw03g
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
help@vivo-us.com
www.vivo-us.com
Chat live with an agent!
309-278-5303
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Vivo MOUNT-VW03G
Summary of Contents for Vivo MOUNT-VW03G
- Page 1 Silver Pneumatic Arm TV Wall Mount Instruction Manual SKU: MOUNT-VW03G Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. https://vivo-us.com/products/mount-vw03g GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST help@vivo-us.com...
- Page 2 CAUTION! DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO MOUNT. We include mounting for brick and concrete walls. If unsure, please contact us at vivo-us. com, email at help@vivo-us.com, or call us at 309-278-9303.
- Page 3 TOOLS NEEDED Phillips Drill Pencil Screwdriver ASSEMBLY STEPS STEP 1 Remove VESA plate from the Mount (A) by removing two bottom nuts with Wrench (T-C) and loosening top two nuts. The plate will lift out from the slots on the top of the bracket. STEP 2 OPTION A: Wood Wall Use Mount (A) to mark mounting holes on wall where stud is located.
- Page 4 STEP 2 (Continued) OPTION B: Concrete/Brick Wall Use Mount (A) to mark mounting holes on wall. Use Bubble Level (T-D) to ensure mount is level. Using a 3/8” drill bit, drill holes at least 2.4” deep into marked locations. Press Anchors (W-B) into holes, then insert ST6.3x5.5mm Screw (W-A) into top hole, leaving 3mm of thread exposed.
- Page 5 STEP 4 Secure VESA Adapters (D, E) to VESA Plate using M6x8mm Screws (S-A) in the appropriate configuration to match your televisions mounting holes. NOTE: VESA adapters are not required for VESA patterns 200mm and smaller.
- Page 6 STEP 5 Attach VESA plate assembly to back of monitor using the appropriate Screws (M-C, M-B) for your monitor and D8 Washers (M-E). For curved monitors, use Screws (M-C, M-D) with M8 Washers (M-E) and Spacers (M-F, M-G). STEP 6 Attach VESA plate with monitor to Mount (A) using previously remove nuts and Wrench (H) as shown in diagram.
- Page 7 Adjust as Desired To adjust gas spring lift strength, turn the screw on the top of the center joint using the 6mm Allen Wrench (T-B). Clockwise will reduce strength, and counter-clockwise will increase (screw turns most easily when arm is facing straight forward). If the screw is difficult to access, remove the plastic arm covers by rocking them up and down until they pop off.
- Page 8 AVG. RESPONSE TIME (within office hrs) - 23% within < 15m - 38% within < 30m - 61% within < 1hr - 83% within < 2hr - 92% within < 3hr FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com...
Need help?
Do you have a question about the MOUNT-VW03G and is the answer not in the manual?
Questions and answers