Summary of Contents for Scag Power Equipment GC-STC
Page 1
All manuals and user guides at all-guides.com MODEL GC-STC THIS MANUAL CONTAINS THE OPERATING INSTRUCTIONS AND SAFETY INFORMA- TION FOR YOUR SCAG ACCESSORY. READ- ING THIS MANUAL WILL PROVIDE YOU WITH MAINTENANCE AND ADJUSTMENT PROCEDURES TO KEEP YOUR ACCESSORY PERFORMING TO MAXIMUM EFFICIENCY.
Page 2
This manual covers the operating instructions and illustrated parts list for: GC-STC with a serial number of 6910001-6919999 Always use the entire serial number listed on the serial number tag when referring to this product.
A replacement manual is available from your authorized Scag Service Dealer or by contacting: USE OF OTHER THAN ORIGINAL SCAG Scag Power Equipment, Service Department at P.O. REPLACEMENT PARTS WILL VOID THE Box 152, Mayville, WI 53050. Please indicate the WARRANTY.
Page 4
ON RH SPINDLE SHAFT - HARDWARE ON TOP OF EXISTING REMOVE EXISTING SPINDLE DRIVE RT. SIDE BELT PULLEY COVER REMOVE U-NUT RIGHT SIDE OF CUTTER DECK SHOWN (Note: Some parts not shown for viewing purposes.) Figure 1- GC-STC install art FIGURE 1...
Page 5
All manuals and user guides at all-guides.com REAR OF FRONT OF CUTTER DECK DISCHARGE CHUTE OPENING CUTTER DECK VIEW FROM RIGHT SIDE OF CUTTER DECK Figure 2- GC-STC install art FIGURE 2 CATCH PLATE ELASTIC STOP NUT BLOWER ASSEMBLY MOUNTING...
Page 6
All manuals and user guides at all-guides.com 11. Install the blower mounting bracket to the deck 20. Install the hood to the hinge brackets using bolts using carriage bolts (p/n 04003-11), lockwashers, (p/n 04001-19), flatwashers (p/n 04041-07) and and nuts. Do not fully tighten the hardware at elastic stop nuts (p/n 04021-09).
Page 7
Mounting Pins Assembly P/N 49452 Rear Frame Hopper Mounting Brackets Figure 4- GC-STC install art FIGURE 4 Carraige Bolt 1/4-20 x 3/4" Seal Retainer Bag Support Bracket Center Lock Nut 1/4-20 Figure 5 - GC-STC install art Seal FIGURE 5...
Page 8
See Figure 6. CLEVIS PIN P/N 04064-15 ADAPTER RUE COTTER PIN P/N 04069-03 GC-STC removal art 3 Figure 8 BLOWER MOUNTING ASSEMBLY BRACKET 8. Never operate your mower without the complete grass catcher, all guards and covers installed, or the discharge chute properly installed.
Page 9
All manuals and user guides at all-guides.com NOTES...
Page 10
All manuals and user guides at all-guides.com GC-STC BLOWER HOUSING ASSEMBLY 390S0200...
Page 11
All manuals and user guides at all-guides.com GC-STC BLOWER HOUSING ASSEMBLY Ref. Part Number Description 04067-07 Pin, Ring 2-1/4" Long 481547 Lanyard, Deck Height Pin 04019-02 Nut, Serr. Flange 1/4-20 04001-59 Bolt, Hex Head 1/4-20 x 1-1/4" 04001-01 Bolt, Hex Head 1/4-20 x 3/4"...
Page 12
All manuals and user guides at all-guides.com GC-STC BLOWER MOUNTING COMPONENTS 12 13 390S0203...
Page 13
All manuals and user guides at all-guides.com GC-STC BLOWER MOUNTING COMPONENTS Ref. Part Number Description 482276 Belt Cover, GC-STC 04029-04 Wingnut, Plastic 3/8 Small 482300 Cap, Square Vinyl 04021-08 Nut, Elastic Stop 1/4-20 482272 Adapter, Blower GC-STC 04040-14 Flatwasher, 1/4-.312 x .750 x .065 48137-04 Rubber Strap 7-3/4"...
Page 14
All manuals and user guides at all-guides.com GC-STC BUCKET SUPPORT COMPONENTS (UPPER) 12 13 14 390S0202...
Page 15
All manuals and user guides at all-guides.com GC-STC BUCKET SUPPORT COMPONENTS (UPPER) Ref. Part Number Description 423302 Screen, Catcher Hood 04090-02 Pop Rivet, 3/16 x .652 04041-19 Flatwasher, 3/16-.196 x .469 x .048 04001-19 Bolt, Hex Head 3/8-16 x 1"...
Page 16
All manuals and user guides at all-guides.com GC-STC BUCKET SUPPORT COMPONENTS (LOWER) 390S0201...
Page 17
All manuals and user guides at all-guides.com GC-STC BUCKET SUPPORT COMPONENTS (LOWER) Ref. Part Number Description 04090-02 Pop Rivet, 3/16 x .652 482321 Seal, Hood 423262 Tube, Upright 04041-07 Flatwasher, 3/8-.391 x .938 x .105 04021-09 Nut, Elastic Stop 3/8-16...
Page 18
All manuals and user guides at all-guides.com GC-STC DECALS 481039 482275 481327 482293...
This warranty does not cover engines and electric starters, which are warranted separately by their manufacturer. Scag Power Equipment reserves the right to change or improve the design of any accessory without assuming any obligation to modify any accessory previously manufactured.
Need help?
Do you have a question about the GC-STC and is the answer not in the manual?
Questions and answers