Page 2
CONCERN, PRUDENCE, AND PROPER TRAINING OF THE PERSONNEL INVOLVED IN THE OPERATION, TRANSPORT, MAINTENANCE, AND STORAGE OF THE EQUIPMENT. This manual covers the operating instructions and illustrated parts list for: GC-VRII with a serial number of P6200001 to P6299999 Always use the entire serial number listed on the serial number tag when referring to this product.
Section 1 GENERAL INFORMATION 1.1 INTRODUCTION A replacement manual is available from your authorized Scag Service Dealer or by contacting: Scag Power This manual has been prepared to provide the Equipment, Service Department at P.O. Box 152, Mayville, information you need to correctly assemble, operate, and WI 53050.
Page 4
Section 2 2.1 ASSEMBLY INSTRUCTIONS - CUTTER - NOTE - DECK AND BLOWER COMPONENTS Retain the original belt cover. This cover MUST be reinstalled any time the complete catcher system is removed. - NOTE - Use the illustrated parts list as a part number r e fe r e n c e w h e n fo l l ow i n g t h e a s s e m bl y instructions.
Page 5
Section 2 3/8 ELASTIC STOP 3/8 LOCKWASHER UNDER SIDE OF DRILLED VELOCITY-PLUS Custom Cut Baffle CUTTER DECK SHOWN 3/8 Elastic Stop Nut 3/8-16 x 1’’ Carriage Bolt Baffle Weldments 48V & 52V - 452383 61V - 452384 3/8 FLATWASHER p/n 463133 3/8-16 x 1-1/4”...
Page 6
Section 2 -NOTE- 3/8 ELASTIC STOP May need to loosen the rear belt cover guard to 3/8 LOCKWASHER route belt around the blower pulley. DRILLED BACK SIDE IDLER PULLEY BLOWER PULLEY p/n 463137 3/8 FLATWASHER 3/8-16 x 1-1/4’’ BOLT SPINDLE FRONT SIDE PULLEY IDLER PULLEY...
Page 7
Section 2 3/8 Flatwasher 3/8 Lockwasher 3/8-16 x 1-1/4’’ Bolt Figure 2-10. Hopper Mounting Hardware Install Figure 2-12. Hopper Installation 15. Install the mounting pins on to the rear of the 17. Install hose adapter (p/n 461387) to the blower machine as shown.
Page 8
Section 2 3. Install the weight onto the weight bar. Slide the weight to the operator's far left side of the machine, secure using the pin (p/n 485172) in the hole to the inside of the weight. See Page 21 for the correct number of weights required.
Page 9
Section 3 3.1 GRASS CATCHER REMOVAL WARNING INSTRUCTIONS Prepare the machine so there is easy and safe access to Do not operate without discharge chute, mulch the work area. Park the machine on a flat, level surface kit, operator controlled discharge chute (OCDC), and apply the parking brake.
Section 5 ILLUSTRATED PARTS LIST 5.1 SCAG APPROVED ATTACHMENTS AND ACCESSORIES Attachments and accessories manufactured by companies other than Scag Power Equipment are not approved for use on this machine.
Page 17
Section 5 GC-VRII HOOD COMPONENTS Ref. Part No. Description 04001-32 Bolt, 3/8-16 x 1¼" 04041-11 Washer, Flat 3/8, .406 x 1.5 x .1793 462932 Hood Assembly, Catcher With Decal (INCL. 485840,4,23,33,34,36) 483589 Hood, Seal 04041-07 Washer, Flat, 3/8, .391 x .938 x .1046...
Page 18
Section 5 GC-VRII BAG SUPPORT COMPONENTS GC-2B 2017 BSC...
Page 19
Section 5 GC-VRII BAG SUPPORT COMPONENTS Ref. Part No. Description 04090-02 Pop Rivet, 3/16 x .652 483589 Seal, GC Hood 424753 Retainer, Seal 04021-02 Nut, Center Lock 1/4-20 04021-10 Nut, Elastic Stop 5/16-18 462966 Bag Assembly 452675 Frame Weldment, Bag Support 04001-01 Bolt, 1/4-20 x 3/4"...
Page 20
Section 5 GC-VRII SUPPORT FRAME COMPONENTS...
Page 21
Section 5 GC-VRII SUPPORT FRAME COMPONENTS Ref. Part No. Description 452832 Handlebar Weldment, SVRII 04019-04 Nut, Serrated Flange, 3/8-16 04017-39 Bolt, Serrated Flange, 1/2-13 x 1¾" 452804 Mainframe Weldment, SVRII 04003-03 Bolt, Carriage, 3/8-16 x 2" 04003-22 Bolt, Carriage, 3/8-16 x 1¼"...
Page 22
Section 5 GC-VRII FRONT WEIGHT COMPONENTS...
Page 23
Section 5 GC-VRII FRONT WEIGHT COMPONENTS Ref. Part No. Description 04021-11 Nut, Lock, elastic Stop, 7/16-14 04030-05 Washer, Lock, 7/16 Spring 427851 Mounting Bracket, Weight Bar - LH 04117-04 Nut, Lock, elastic Stop With Flange, 1/2-13 04001-117 Bolt, 7/16-14 x 1¾"...
This warranty does not cover engines and electric starters, which are warranted separately by their manufacturer. Scag Power Equipment reserves the right to change or improve the design of any accessory without assuming any obligation to modify any accessory previously manufactured.
Need help?
Do you have a question about the GC-VRII and is the answer not in the manual?
Questions and answers