Attaching the Fender and Headlight Attaching the Front Disc Brake Attaching the Front Tire Attaching the Seat Attaching the Pedals Charging the Battery Operating the Journey LCD Display Pedal Assist Mode Connecting to Bluetooth® Riding the Journey Care and Maintenance...
Page 5
1. WHAT’S IN THE BOX 1. FRONT TIRE 6. SEAT 2. HEADLIGHT 7. FRONT DISC BRAKE 3. HANDLEBAR 8. KICKSTAND 4. CHARGING PORT 9. CHARGER 5. SEAT CLAMP 10. CHARGING CABLE Assembling the Journey should take between 30-35 minutes (including unboxing).
Guard on the Handlebar Stem. Handlebar Stem. Make sure the Then, remove the Metal Guard. markings on the Handlebar are centered. Replace the Metal Guard by tightening the 4 bolts. Please Note: Assembling the Journey should take between 30-35 minutes (including unboxing).
4. ATTACHING THE FENDER AND HEADLIGHT Small Bolt Small screw and washer Connect the Support Bars to Connect the Support Bars to the Fender using the small bolt the Front Fork using the 2 small in the Fender. screws and 2 washers. Connect the Fender and Headlight Connect the two small wires to to the Front Fork using the Large Bolt...
6. ATTACHING THE FRONT TIRE Remove the plastic protector from Hook the Fork onto both sides of the Fork. Then, Slide the Front Tire the tire and slide the Disc Brake between the Fork. into the Disc. Spring Quick Release Remove the Cap and one Spring Slide the Quick Release through from the Quick Release.
Page 11
Close Lever Tighten the Cap and Lever. Close the Lever to lock.
7. ATTACHING THE SEAT Seat Clamp closed • Slide the Seat Post into the Seat Tube. • Close the Seat Clamp to secure the Seat. • If necessary, tighten the Seat Clamp by turning the Lever and Knob.
8. ATTACHING THE PEDALS • Please look at the inside of each Pedal and see which is labeled Right (R) and Left (L). • Tighten by turning the Pedals toward the Front Tire. • Use a 15mm wrench to make sure the Pedals are tight and secure.
Only use the included charger • Plug the charger into the wall before the Charging Port • Don’t turn on the Journey while it’s charging (it needs its rest) • Charge the battery until it is fully charged - up to 5 hours •...
10. OPERATING THE JOURNEY 1. Handbrakes - Squeeze the Handbrakes to come to a stop (apply the brakes slowly to avoid stopping abruptly or losing control). 2. Bell 3. LCD Display - Shows Battery Level, Speedometer, and more. Please see the next section for more information.
Increase Button: Press to increase the Pedal Assist level. Decrease Button: Press to decrease the Pedal Assist level. Walk Button: Hold for 3 seconds to turn the Walk Mode on or off. When Walk Mode is activated, the Journey will move at about 3 mph.
12. PEDAL ASSIST MODE Pedal Assist Level The Pedal Assist Mode provides power from the motor. Level (0) — will not use Pedal Assist Level (1-3) — Low Pedal Assist will require effort from you to pedal Level (4-6) — Medium Pedal Assist will require some effort from you to pedal Level (7-9) —...
13. CONNECTING TO BLUETOOTH® Your Jetson Journey is Bluetooth® 4.0 enabled, so you can pair it with the Ride Jetson app on your personal Bluetooth® enabled device. The Ride Jetson app is available for download from the App Store and the Google Play Store, and it’s free!
Tighten all screws and locking nuts before each ride to ensure they are tight. • While riding the Journey, keep your feet on the Pedals. • Do not ride with your feet dangling over the sides and always stay seated...
CLEANING THE JOURNEY To clean the Journey, carefully wipe with a damp cloth, then dry with a dry cloth. Do not use water to clean the Journey, as the electrical and electronic systems may get wet, resulting in personal injury or malfunction of the Journey.
16. SAFETY WARNINGS • For your safety, please read the user manual and safety warnings carefully, and make sure you understand and accept all the safety instructions. The user will be responsible for any loss or damage caused by improper use. •...
Page 22
MODIFICATIONS Do not attempt to disassemble, modify, repair, or replace the unit or any components of the unit without instruction from Jetson Customer Support. This will void any warranty, and can lead to malfunctions which may cause injury. ADDITIONAL OPERATION CAUTIONS Do not lift the product off the ground while it is on and the wheels are in motion.
17. SAFETY CHECKLIST FOR SAFETY AND TO LIMIT THE RISK OF FIRE AND ELECTRIC SHOCK: A. Read all the instructions before using the product. B. To reduce the risk of injury, close supervision is necessary when the product is used near children.
Page 24
WHEELS AND TIRES • Make sure that the tires are inflated to within their maximum recommended tire pressure of 45 - 60 PSI. • Check tires for excessive wear or any damage and that the wheel rims are not damaged. Check that the wheel spokes are not broken and that the axle nuts are tight.
Page 26
US 1-(888) 976-9904 help@ridejetson.com www.ridejetson.com...