Multitech SocketWireless MT800SWM Reference Manual page 37

#WLANDATARATE – WLAN Transmission Data Rate
.............................................................................11
#WLANDISCONNECT – Disconnect with AP ..........12
#WLANDOZE – Move Module into Power Save ......13
#WLANENABLE – Auto Connect Module with AP ...12
#WLANGETRSSI – Received Signal Strength.........13
#WLANIBSSCHANNEL – Channel for Ad-Hoc Mode
.............................................................................12
#WLANNETWORKMODE – WLAN Network Mode .10
#WLANPOWERSAVE – Enable Power Save at Boot
.............................................................................13
#WLANROAM – Enable/Disable Roaming...............13
#WLANSCANMODE – Scanning Mode ...................11
#WLANSECURITYMODE – Security Mode of WLAN
Module..................................................................10
#WLANSETTXPOWER – Transmit Power...............12
#WLANSSID – SSID of WLAN.................................11
#WLANTXPOWER – Maximum Transmit Output
Power for the WLAN Module ................................11
A
Address of the POP3 Server – #POP3SERV...........25
Address of the Recipient – #SMTPRECiADD ..........16
Address of the Remote TCP Server – #TCPSERV ..20
Auto Connect Module with AP – #WLANENABLE ...12
Auto Connect to TCP Server –
#TCPAUTOCONNECT.........................................22
C
Channel for Ad-Hoc Mode – #WLANIBSSCHANNEL
.............................................................................12
Close TCP Listening Mode – #TCPSTOP................21
Close the UDP Listening Mode – #UDPSTOP.........23
Coding the ETX Character – #TCPDLEMODE ........20
Configure the DNS Server – #IPDNSSERV ...............7
Connect with AP – #WLANCONNECT.....................12
Country Code – #WLANCOUNTRYCODE...............11
D
Default Gateway – #IPDEFGW ..................................6
Delay before Sending UDP Datagram –
#UDPTXDELAY....................................................22
Delete Mail from Inbox – #POP3DELMAIL ..............26
DHCP Client – #IPDHCP ...........................................6
Disconnect with AP – #WLANDISCONNECT ..........12
Display All AT Parameters – #VALL.........................34
Display Association Information –
#WLANASSOCINFO ............................................14
Display DNS Table – #IPDNSTABLE.........................8
Display the Current Status of the Device – #VSTATE
.............................................................................34
DNS Server 1 – #IPDNSSERV1 ................................6
DNS Server 2 – #IPDNSSERV2 ................................7
Domain Name of the Sender – #SMTPDOMAIN......15
Download Files from the FTP Server – #FTPGET ...30
E
Enable Power Save at Boot – #WLANPOWERSAVE
.............................................................................13
Enable/Disable Auto Listen – #TCPAUTOLISTEN...24
Enable/Disable Boot Message – #BOOTMSG.........35
Enable/Disable Roaming – #WLANROAM...............13
Enable/Disable Watchdog – #WATCHDOG.............35
Escape Sequence – S2............................................35
Multi-Tech Systems, Inc. AT Commands for the MT800SWM & MTS2WFA (S000425D)
F
FTP Interactive Mode – #FTPCSTART....................31
FTP Mode – #FTPMODE.........................................28
FTP Module – #FTP?...............................................31
FTP Server Address – #FTPSERV ..........................28
G
Give a Domain Name – #IPQUERY...........................7
Give Sender Address – #SMTPSENDERADDR ......15
Give Sender Name – #SMTPSENDERNAME .........15
Give the CC Address – #SMTPCCRECi ..................15
H
Header Information of the Mail –
#POP3RECVMAILHEAD......................................26
I
Initiate the UDP Session in Listen Mode –
#UDPSTART ........................................................22
Initiate UDP Session in Active Mode – #UDPOPEN 23
IP Address of Remote Device – #PINGREMOTE ......9
IP Module – #IP?........................................................7
K
Keys for WEP128 Security Mode – #WEP128KEY..10
Keys for WEP64 Security Mode – #WEP64KEY......10
L
List of Emails in Inbox – #POP3RECVMAILLIST .....26
Lists the Listening TCP Ports – #TCPLISTENLIST..23
M
Mail Body – #SMTPBODYi ......................................16
Maximum Transmit Output Power for the WLAN
Module – #WLANTXPOWER ...............................11
Move Module into Power Save – #WLANDOZE ......13
Move Module out of Power Save – #WLANACTIVATE
.............................................................................13
N
Name of the Downloadable File from the FTP Server
– #FTPGETFILENAME ........................................29
Name of the Uploadable File to the FTP Server –
#FTPPUTFILENAME............................................29
Number of PING Requests – #PINGNUM..................9
O
Open a Listening TCP Connection – #TCPLISTEN .21
Open a TCP Connection – #TCPOPEN...................21
P
Password of the FTP Server – #FTPPW..................29
Password of the POP3 Account – #POP3PW..........25
Path of Files to Upload and Download – #FTPDIR ..29
PING – #PINGSTART................................................9
PING Module – #PING?.............................................9
POP3 Header – #POP3HEADERMODE..................25
POP3 Module – #POP3? .........................................27
Port of Remote Peer Used for TCP Session –
#TCPPORT ..........................................................20
Port of the FTP Server – #FTPPORT.......................28
Port of the POP3 Server – #POP3PORT .................25
Port of the SMTP Server – #SMTPPORT ................16
Previous Command – A/ ..........................................34
Index
37