Internal Preset Memory Capability; Power Management Function; Ddc; Location Considerations - Mitsubishi Diamond Pro 710 User Manual

1.2

Internal Preset Memory Capability

To minimize adjustment needs, the factory has preset
popular display standards into the monitor, as shown in
Table 1. If any of these display standards are detected by
the microprocessor, the picture size and position are auto-
matically adjusted. All of the factory presets may be
overwritten by adjusting the user controls. The monitor is
capable of automatically storing up to 6 additional display
standards. The new display information must differ from
any of the existing display standards by at least 1kHz for the
horizontal scan frequency or 5Hz for the vertical scan
frequency or the sync signal polarities must be different.
Table 1. Memory Buffer Factory Presets
PRESET
TIMING Fh(kHz) Fv (Hz)
640 x 480 N.I.
640 x 480 N.I.
832 x 624 N.I.
800 x 600 N.I.
1024 x 768 N.I.
1152 x 870 N.I.
1024 x 768 N.I.
1280 x 1024 N.I.
1.3

Power Management Function

The monitor has a power management function which
reduces the power consumption of the monitor when not in
use. There are three reduced power level modes.
Check your computer manual for the instructions for setting
the power saving timing.
Mode Power
Normal 105 W
Stand-By 80 W
Suspend 15 W
Off 8 W
1.4

DDC

The monitor includes the DDC1 and DDC2B feature more
commonly known as "Plug & Play". DDC (Display Data
Channel) is a communication channel over which the
monitor automatically informs the computer system about
its capabilities (e.g. each supported resolution with its
corresponding timing).
DDC is routed through previously unused pins of the 15-pin
VGA connector.
The system will perform "Plug and Play" feature if both,
monitor and computer, implement the DDC protocol.
When a Plug & Play computer starts, it identifies the monitor
and loads the appropriate driver automatically. If the
computer does not have the driver installed, a dialog box
will appear asking where the information can be found.
The latest drivers may be downloaded from the "Support"
section of the Mitsubishi website located at:
http://www.mitsubishi-display. com/
Polarity
H V
31.5 60.0 – –
37.5 75.0 – –
49.7 74.5 – –
46.9 75.0 + +
56.5 70.0 – –
68.7 75.1 – –
60.0 75.0 + +
80.0 75.0 + +
Power On Indicator
Green
Red
Red
Red
1.5

Location Considerations

When setting up and using the monitor, keep the following
in mind:
• For optimum viewing, avoid placing the monitor
against a bright background or where sunlight or
other light sources may reflect on the display area of
the monitor; place the monitor just below eye level.
• Place the monitor away from strong magnetic or
electromagnetic fields, such as high capacity trans-
formers, electric motors, large current power lines,
steel pillars, etc....
Magnetism can cause distortion in the picture and/or
color purity.
• Avoid covering the slots or openings of the monitor.
Allow adequate ventilation around the monitor so the
heat from the monitor can properly dissipate. Avoid
putting the monitor into any enclosure that does not
have adequate ventilation.
• Avoid exposing the monitor to rain, excessive
moisture, or dust, as this can cause a fire or shock
hazard.
• Avoid placing the monitor, or any other heavy object,
on the power cord. Damage to the power cord can
cause a fire or electrical shock.
• When transporting the monitor, handle it with care.
1.6

Cleaning Your Monitor

When cleaning the monitor, please follow these guidelines:
• Always unplug the monitor before cleaning.
• Wipe the screen and cabinet front and sides with a
soft dry cloth.
• If the screen requires more than dusting, apply a
household window cleaner to a soft cloth to clean the
monitor screen.
• Do not spray directly on the screen as excess cleaner
may drip into the monitor causing damage.
CAUTION
Do not use benzene, thinner or any volatile substances to
clean the unit as the finish may be permanently marked.
Never leave the monitor in contact with rubber or vinyl for
an extended time period.
- 3 -