Related Manuals for Mitsubishi 930
Summary of Contents for Mitsubishi 930
- Page 1 User’s Manual Diamond Pro 930 Diamond Pro 930 Diamond Pro 930 Diamond Pro 930 Diamond Pro 930 www.nec-mitsubishi.com...
-
Page 2: Declaration Of The Manufacturer
686-1, Nishioi Oi-Machi Ashigarakami-gun Kanagawa 258-8533, Japan Product NERGY As an E Partner, NEC-Mitsubishi Electronics Display of America, Inc. has determined that this NERGY product meets the E guidelines for energy efficiency. The E emblem does not represent NERGY NERGY EPA endorsement of any product or service. - Page 3 C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to C.S.A. C22.2 No. 950. FCC Information 1. Use the attached specified cables with the Diamond Pro 930 colour monitor so as not to interfere with radio and television reception.
- Page 4 Contents Your new Diamond Pro 930 monitor box* should contain the following: • Diamond Pro 930 Monitor with tilt/swivel base • Power Cord • Captive Signal Cable • User’s Manual • Sales Office List • CD ROM with Setup Software, complete User’s Manual and other helpful files.
-
Page 5: Quick Start
Macintosh (Figure B.1). Attach the 15-pin mini D-SUB end of the captive signal cable to the Diamond Pro 930 Macintosh cable adapter on the computer (Figure B.1). Tighten all screws. 4. Connect one end of the power cord to the Diamond Pro 930 monitor and the other end to the power outlet (Figure C.1). - Page 6 Quick Start – continued Power Outlet Power Cord Figure C.1 Power Button Figure D.1 6 User’s Manual...
-
Page 7: Brightness/Contrast Controls
When activated, your screen image will jump and waver a bit as the screen is demagnetized. Caution: Please allow a minimum of 20 minutes to elapse between uses of the Degauss Control. Diamond Pro 930... -
Page 8: Size And Position Controls
Controls – continued Size and Position Controls Left/Right: Moves the image horizontally (left or right). Down/Up: Moves the image vertically (up or down). Narrow/Wide: Decreases or increases the horizontal size of the image. Short/Tall: Decreases or increases the vertical size of the image. Color Control System Colour presets selects the desired colour setting. - Page 9 (GLOBALSYNC, TOP LEFT, TOP RIGHT, BOTTOM LEFT or BOTTOM RIGHT), use the –/+ control buttons to fine tune the GlobalSync corrections. NOTE: Mitsubishi recommends that you perform GlobalSync correction while running a typical application such as a spreadsheet or text document.
-
Page 10: Recommended Use
• Changing the direction of the monitor while it is powered on may cause image discolouration. To correct this, turn the monitor off for 20 minutes before powering it back on. • When operating the Diamond Pro 930 with the AC 100 - 240 V power source in EU countries except UK, use the power cord supplied. - Page 11 • Use non-interlaced signals with a vertical refresh rate between 75 - 160 Hz • Do not use primary colour blue on a dark background, as it is difficult to see and may produce eye fatigue due to insufficient contrast Diamond Pro 930...
-
Page 12: Specifications
Specifications : l a ° 0 e l f e l l c t i e l l - i t l - i t c i t t n i i t i i t a c i t i t i i t a i t i... - Page 13 The state-of-the-art Mitsubishi U-NX-DBF electron gun and tight 0.24 mm grille pitch delivers precise focus for crisp, clear text and images.
-
Page 14: Troubleshooting
• Check the signal cable and computer in case that the diagnosis message displayed. • Contact Mitsubishi Customer Service in case that the diagnosis message still does not display. – In case that no diagnosis message displayed with LED lit in orange. -
Page 15: Why Do We Have Environmentally Labelled Computers
TCO’99 Diamond Pro 930 Congratulations! You have just purchased a TCO’99 approved and labeled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further develop- ment of environmentally adapted electronics products. - Page 16 TCO’99 – continued TCO’99 demand requires that plastic components weighing more than 25 grams must not contain flame retar- dants with organically bound chlorine and bromine. Flame retardants are allowed in the printed circuit boards since no substitutes are available. Lead** Lead can be found in picture tubes, display screens, solders and capacitors.
- Page 17 Diamond Pro 930...