Hoppe AUDIO MINI Installation Instructions And Owner's Manual
Off-road sound system for cfmoto uforce 1000 / 1000 xl
Hide thumbs
Also See for AUDIO MINI:
- Installation instructions & owner's manual (21 pages) ,
- Installation instructions manual (18 pages) ,
- Installation instructions & owner's manual (18 pages)
Subscribe to Our Youtube Channel
Related Manuals for Hoppe AUDIO MINI
Summary of Contents for Hoppe AUDIO MINI
- Page 1 INSTALLATION INSTRUCTIONS / OWNER’S MANUAL: AUDIO MINI OFF-ROAD SOUND SYSTEM FOR CFMOTO UFORCE 1000 / 1000 XL MODELS www.hoppeindustries.com 22667 FM 15 Troup, TX 75789 (262) 552-2770...
- Page 2 It is critical that proper eye wear, ear protection, and protective clothing is worn throughout the top installation. When you receive your Audio Mini off-road sound system, please check to ensure that all parts and hardware are included. If there are any parts missing or if you have any questions concerning the system at this time call Hoppe at (262)-552-2770 Mon-Thur.
-
Page 3: Table Of Contents
TABLE OF CONTENTS SECTION 1 – Tools Required .................... 4 SECTION 2 – About your Audio Mini sound system ............4 2.1 Applicable Year Models: ..................4 2.2 Audio Equipment Details: ..................4 2.3 Warranty: ........................4 2.4 Care and Maintenance: ..................... 5 2.5 Warnings: ........................ -
Page 4: Section 1 - Tools Required
2.3 Warranty: Your Audio Mini comes equipped with a 1 year limited warranty covering the light, the stereo equipment, and the enclosure. The date of warranty coverage will be determined by the registration date of the warranty card or online warranty registration. -
Page 5: Care And Maintenance
If the warranty is not registered with Hoppe, the warranty period will begin when the Audio Mini was shipped from Hoppe's factory. 2.4 Care and Maintenance: Your off-road sound system does not require any maintenance other than an occasional cleaning. -
Page 6: Section 3 - Pre-Installation Inspection
SECTION 3 – Pre-Installation Inspection Included in your off-road sound system are the following components: Pre-assembled Audio Mini off-road sound system (All speakers and electronics come preinstalled with interior wire harness.) Chassis wire harness Mounting brackets Hardware bag ... -
Page 7: Section 4 - Installation
SECTION 4 – Installation 1. Remove the four factory bolts securing the roof to the visor. Save the hardware for reinstallation in later steps. See Figure 2. Figure 2: Remove the front bolts securing the roof to the visor. 2. Remove the factory bolts from the front visor as indicated in Figure 3. The bolts will be replaced. - Page 8 Verify correct orientation of the mounting bracket. See Figure 4. Note: Driver side shown. (Passenger side similar) Figure 4: Mounting location of the Audio Mini bracket. 4. Reusing the factory bolts, reinstall only the two center bolts securing the roof to the visor.
- Page 9 See Figure 6 and Figure 7. Figure 6: Install the ¼”-20 bolts and washers to mount the Audio Mini to the brackets. Figure 7: Loosely install the sound system on the mounting brackets.
- Page 10 Figure 8: Up-down adjustability of the Audio Mini. 8. Reusing the factory bolts, install the two bolts through the Audio Mini brackets and visor into the roof. Tighten both bolts to secure the brackets to the visor and roof. See Figure 9. Note: Driver side shown. (Passenger side similar) Figure 9: Install the bolts to secure the brackets and visor to the roof.
- Page 11 9. Remove the hood from the front of the vehicle by gently pulling towards the front of the vehicle to remove the 3 hood bosses and then lifting off the hood. See Figure 10. HOOD BOSSES Figure 10: Remove the hood from the vehicle. 10.
- Page 12 Figure 11: Remove the four screws. 11. Route the end of the chassis harness with the mating connector for the Audio Mini along with the wire bundle under the front body panel toward the driver’s front down tube opening. See Figure 12.
- Page 13 12. Gently pull the chassis harness connector through the opening, and connect it to the mating connector on the Audio Mini. The harness will be secured to the cage tube at the end of the installation. See Figure 13. PULL CONNECTOR THROUGH OPENING Figure 13: Chassis harness routing up the front down tube.
- Page 14 IGNITION WIRE ROUTING Figure 14: Accessory wire routing for ignition power source under the dash. 14. Remove the center sections of the dash to gain access to the factory harness connectors on the 12V power point. Gently pull to release the plastic clips in the areas shown.
- Page 15 15. Connect the Audio Mini chassis harness connectors on the orange ignition wire to the connectors on the 12V power point. Match the male and female connectors from the chassis harness to the factory harness. See Figure 16 and Figure 17.
- Page 16 BLACK TO - RED TO + Figure 18: Winch contactor cable connections. 17. Zip tie the chassis harness under the hood, making sure to orient the relay upright as shown. Clean the cage surface with the provided alcohol wipe, and place zip ties and mounts at the indicated locations on the driver’s front down tube.
- Page 17 Figure 19: Secure the chassis harness under the hood. Figure 20: Secure the chassis harness to the frame tube. 18. Reinstall the four screws and hood. See Figure 10, and Figure 11. Revision - 17 of 18...
- Page 18 19. Reinstall the two center sections of the dash. See Figure 15. 20. You are now ready to enjoy the music and lighting provided by your Audio Mini off-road sound system. Basic operation works as follows: Turn the vehicle ignition switch on to power up the stereo system. (You must press the power button for first time connections or if the power was previously turned off manually.)
Need help?
Do you have a question about the AUDIO MINI and is the answer not in the manual?
Questions and answers