Hoppe Audio Mini Installation Instructions & Owner's Manual
Off-road sound system for honda pioneer 1000 / pioneer 1000-5 models
Hide thumbs
Also See for Audio Mini:
- Installation instructions & owner's manual (21 pages) ,
- Installation instructions manual (18 pages) ,
- Installation instructions and owner's manual (18 pages)
Related Manuals for Hoppe Audio Mini
Summary of Contents for Hoppe Audio Mini
- Page 1 INSTALLATION INSTRUCTIONS / OWNER’S MANUAL: AUDIO MINI OFF-ROAD SOUND SYSTEM FOR HONDA PIONEER 1000 / PIONEER 1000-5 MODELS www.hoppeindustries.com 22667 FM 15 Troup, TX 75789 (262) 552-2770...
- Page 2 It is critical that proper eye wear, ear protection, and protective clothing is worn throughout the top installation. When you receive your Audio Mini off-road sound system, please check to ensure that all parts and hardware are included. If there are any parts missing or if you have any questions concerning the system at this time call Hoppe at (262)-552-2770 Mon-Thur.
-
Page 3: Table Of Contents
TABLE OF CONTENTS SECTION 1 – Tools Required .................... 4 SECTION 2 – About your Audio Mini sound system ............4 2.1 Applicable Year Models: ..................4 2.2 Audio Equipment Details: ..................4 2.3 Warranty: ........................5 2.4 Care and Maintenance: ..................... 5 2.5 Warnings: ........................ -
Page 4: Section 1 - Tools Required
SECTION 2 – About your Audio Mini sound system 2.1 Applicable Year Models: This Audio Mini off-road sound system is designed to fit the following Pioneer 1000/ Pioneer 1000-5 models: 2016-2021 Pioneer 1000 (all versions) ... -
Page 5: Warranty
2.3 Warranty: Your Audio Mini comes equipped with a 1 year limited warranty covering the light, the stereo equipment, and the fiberglass enclosure. The date of warranty coverage will be determined by the registration date of the warranty card or online warranty registration. -
Page 6: Warnings
2.5 Warnings: This off-road system adds up to 25 lbs. to your vehicle and is located up high on the roll cage. This increases the vehicle’s center of gravity and changes the vehicle dynamics and handling characteristics. Use extra caution as you learn the driving characteristics of your vehicle with your new off-road sound system installed. -
Page 7: Section 3 - Pre-Installation Inspection
SECTION 3 – Pre-Installation Inspection Included in your off-road sound system are the following components: Pre-assembled Audio Mini off-road sound system (All speakers and electronics come preinstalled with interior wire harness.) Chassis wire harness Mounting brackets Hardware bag ... -
Page 8: Section 4 - Installation
Figure 2: Remove the factory safety net bolts. 2. Place the provided loop clamps in the approximate mounting location on the front roll bar. The Audio Mini brackets will rest on the loop clamps and be tightened in the following steps. See Figure 3. - Page 9 Audio Mini placement. See Figure 5. Figure 5: Hardware for mounting the loop clamps to the brackets. 5. Using an assistant, hang the Audio Mini off-road sound system on the brackets using the supplied ¼”-20 bolts and washers (loosely tightened). Note: The sound system weighs up to 25 lbs.
- Page 10 Figure 6: Install the ¼”-20 bolts and washers to mount the Audio Mini to the brackets. Figure 7: Loosely install the sound system on the mounting brackets. 6. Tighten the 4 bracket mounting bolts so that the Audio Mini is equally spaced from the front roll bar.
- Page 11 See Figure 9. Figure 9: Up-down positioning of the Audio Mini. 8. Plug the chassis harness into the mating connector on top of the Audio Mini. Route the chassis harness over the front roll bar as shown in Figure 10.
- Page 12 Figure 10: Chassis harness connected and routed over front roll bar. 9. Route the chassis harness, using the provided zip ties, down the driver’s front pillar. Zip ties are at the indicated locations. See Figure 11. Revision - 12 of 18...
- Page 13 Figure 11: Route the chassis harness down the driver’s front pillar. 10. Remove the radiator hood access panel from the front of the vehicle by lifting and rotating the ¼ turn clips, lifting the hood, and sliding it towards the front of the vehicle.
- Page 14 Figure 12: Remove the radiator hood access panel. 11. Remove the right Torx screw and the 3 plastic rivets to route the wiring under the plastic panel. The plastic rivets are released by first prying the center head up, then pulling the entire rivet out. See Figure 13. Figure 13: Remove the Torx screw and plastic rivets to run the chassis harness under the panel.
- Page 15 12. Connect the chassis harness battery cables to the battery. Remove the battery bolts from each terminal as you connect the cables, and replace the bolts with the provided M6 x 1.0 x 14 mm battery bolts to clamp the cables on top of the existing cables.
- Page 16 RUBBER PROTECTOR IGNITION WIRE AND CONNECTORS Figure 15: Ignition wire and connector routing. UNHOOK AT THE CORNER Figure 16: Rubber protector access location. Revision - 16 of 18...
- Page 17 Figure 17: Connection location for chassis harness connectors. 15. Reinstall the Torx screw, plastic rivets, and hood. 16. You are now ready to enjoy the music and lighting provided by your Audio Mini off-road sound system. Basic operation works as follows: a.
- Page 18 To learn about the more advanced features and operation of your stereo, visit the Kicker website links found in SECTION 2 – About your Audio Mini sound system of this document. Thank you for choosing the Hoppe Audio Mini off-road sound system for you Honda Pioneer UTV.
Need help?
Do you have a question about the Audio Mini and is the answer not in the manual?
Questions and answers