Hoppe AUDIO MINI Installation Instructions & Owner's Manual
Off-road sound system for polaris rzr / rzr 4 models
Hide thumbs
Also See for AUDIO MINI:
- Installation instructions & owner's manual (21 pages) ,
- Installation instructions manual (18 pages) ,
- Installation instructions and owner's manual (18 pages)
Subscribe to Our Youtube Channel
Related Manuals for Hoppe AUDIO MINI
Summary of Contents for Hoppe AUDIO MINI
- Page 1 INSTALLATION INSTRUCTIONS / OWNER’S MANUAL: AUDIO MINI OFF-ROAD SOUND SYSTEM FOR POLARIS RZR / RZR 4 MODELS www.hoppeindustries.com 22667 FM 15 Troup, TX 75789 (262) 552-2770...
- Page 2 It is critical that proper eye wear, ear protection, and protective clothing is worn throughout the top installation. When you receive your Audio Mini off-road sound system, please check to ensure that all parts and hardware are included. If there are any parts missing or if you have any questions concerning the system at this time call Hoppe at (262)-552-2770 Mon-Thur.
-
Page 3: Table Of Contents
TABLE OF CONTENTS SECTION 1 – Tools Required .................... 4 SECTION 2 – About your Audio Mini sound system ............4 2.1 Applicable Year Models: ..................4 2.2 Audio Equipment Details: ..................4 2.3 Warranty: ........................5 2.4 Care and Maintenance: ..................... 5 2.5 Warnings: ........................ -
Page 4: Section 1 - Tools Required
SECTION 2 – About your Audio Mini sound system 2.1 Applicable Year Models: This Audio Mini off-road sound system is designed to fit the following Polaris RZR / RZR 4 models: 2015-2021 RZR 900 through 1000 (all versions excluding Turbo S, PRO XP, and 2021 Trail models) ... -
Page 5: Warranty
2.3 Warranty: Your Audio Mini comes equipped with a 1 year limited warranty covering the light, the stereo equipment, and the fiberglass enclosure. The date of warranty coverage will be determined by the registration date of the warranty card or online warranty registration. -
Page 6: Warnings
Fuse 1: 15 amp mini fuse for light / radio receiver power. 2.5 Warnings: This off-road system adds up to 25 lbs. to your vehicle and is located up high on the roll cage. This increases the vehicle’s center of gravity and changes the vehicle dynamics and handling characteristics. -
Page 7: Section 3 - Pre-Installation Inspection
SECTION 3 – Pre-Installation Inspection Included in your off-road sound system are the following components: Pre-assembled Audio Mini off-road sound system (All speakers and electronics come preinstalled with interior wire harness.) Chassis wire harness Mounting brackets Hardware bag ... -
Page 8: Section 4 - Installation
1. If you have a roof installed, it will need to be removed for the installation of your Audio Mini. Remove the roof, and then remove the screw shown in Figure 2 to gain access to the front cross member bolts. - Page 9 3. Place the provided loop clamps in the approximate mounting locations on the outside roll bars. The Audio Mini brackets will rest on the loop clamps and be tightened in the following steps. See Figure 4. FRONT REAR Figure 4: Approximate locations of the loop clamps.
- Page 10 5. Use the supplied 3/8”-16 x 1” bolts, washers, and nylock nuts to secure the loop clamp to the mounting bracket. Tighten both the loop clamp bolt and the front cross member bolt to secure to bracket to the roll cage. See Figure 6. Figure 6: Hardware for mounting the loop clamps to the brackets.
- Page 11 8. Remove the Torx screw on top of the driver’s side dash by the front frame tube. The harness will route under this panel in later steps. See Figure 8. REMOVE TORX SCREW Figure 8: Remove the dash Torx screw. 9.
- Page 12 10. Route the mating connector from under the coolant tank along the frame to the opening in the driver side front fender well. See Figure 10 and Figure 11. INTO DRIVER’S FRONT FENDER WELL FROM UNDER COOLANT TANK Figure 10: Chassis harness routing along frame into fender well. Revision - 12 of 18...
- Page 13 ALONG FRAME TO OPENING OPENING TO UNDERSIDE OF DASH Figure 11: Chassis harness routing in driver’s front fender well. 11. Continue routing the harness under the driver’s side dash, and then route the harness between the dash panels up toward the driver’s front frame tube. Gently push the top dash panel upwards to push the connector through, pulling the slack from the harness.
- Page 14 THROUGH DASH TO FRONT FRAME TUBE FROM FRONT FENDER WELL Figure 12: Harness routing path from fender well through the dash. Revision - 14 of 18...
- Page 15 12. Route the harness up the front driver’s frame tube to the front cross member, as shown in Figure 14. Loosely zip tie the harness to the frame tube, waiting to fully tighten them until the Audio Mini is tightened in the desired position. Figure 14: Harness route up the front frame tube.
- Page 16 Mini once installed, so it is important to follow this step closely to not repeat work. See Figure 15 and Figure 16. Figure 15: Install the ¼”-20 bolts and washers to mount the Audio Mini to the brackets. Figure 16: Loosely install the sound system on the mounting brackets.
- Page 17 16. Reinstall the hood and Torx screws. See Figure 2, Figure 7, and Figure 8. Reinstall your roof if it was removed. 17. You are now ready to enjoy the music and lighting provided by your Audio Mini off-road sound system. Basic operation works as follows: ...
- Page 18 To learn about the more advanced features and operation of your stereo, visit the Kicker website links found in SECTION 2 – About your Audio Mini sound system of this document. Thank you for choosing the Hoppe Audio Mini off-road sound system for your Polaris RZR UTV.
Need help?
Do you have a question about the AUDIO MINI and is the answer not in the manual?
Questions and answers