Related Manuals for AVANT Leguan 50
Summary of Contents for AVANT Leguan 50
- Page 1 English Leguan 50 Access platform 2023 1 Operator's Manual for Attachment Leguan 50 Access platform From serial number 290 Product number A34812 www.avanttecno.com A438683 2023 1 EN 2022-...
- Page 2 Leguan 50 Access platform 2023 1 Figure 1 - Leguan 50 Access platform in transport configuration Figure 2 - Leguan 50 Access platform attached to Avant-loader...
-
Page 3: Table Of Contents
Leguan 50 Access platform 2023 1 CONTENTS 1. FOREWORD ............................4 Warning symbols used in this manual ........................... 5 2. DESIGNED PURPOSE OF USE......................6 3. SAFETY INSTRUCTIONS FOR USING THE ATTACHMENT ............7 Personal protective equipment ..........................10 Safe shutdown procedure ............................10 4. -
Page 4: Foreword
If you sell or transfer the equipment, be sure to hand over this manual to the new owner. If the manual is lost or damaged, you can request a new one from your Avant dealer or from the manufacturer. -
Page 5: Warning Symbols Used In This Manual
5 (34) Warning symbols used in this manual The following warning symbols are used throughout this manual. They indicate factors that must be taken into account to reduce the risk of personal injury or damage to property: WARNING SAFETY ALERT SYMBOL This symbol means: “Warning, be alert! Your safety is involved!”... -
Page 6: Designed Purpose Of Use
The AVANT Leguan 50 Access platform is an attachment that is suitable for use with AVANT compact loaders that are shown in Table 1. The Leguan 50 is a mobile lifting platform for indoor and outdoor use and it is designed and manufactured to be an attachment for AVANT compact loaders. -
Page 7: Safety Instructions For Using The Attachment
The Leguan 50 Access platform does not require a type-approval by a notified body. However, local regulations may mandate a periodic inspection of lifting equipment that is intended for lifting of persons. - Page 8 Risk of crushing - Never overload the platform. Overloading the platform can cause serious injury or death. The maximum permitted load for the Leguan 50 Access platform is 200 kg and the maximum allowed number of persons is 2. Do not overload the platform.
- Page 9 9 (34) Make sure to use only an attachment that is in good condition. Do not modify the attachment in a manner that would affect its safety. Drilling holes or welding hooks or other objects on the attachment is prohibited. ...
-
Page 10: Personal Protective Equipment
10 (34) Risk of crushing - Never allow anyone to get under a lifted attachment or loader boom. Keep in mind that the loader boom can be lowered or tilted even if the engine has WARNING been shut down (crushing hazard). The loader is not intended to be left to keep a load elevated for longer periods. -
Page 11: Technical Specifications
Noise level at platform control site: See operator’s manual of the loader Compatible Avant-loader: See Table 1 Table 3 - Main components of the Leguan 50 Access platform Frame Adjustable storage support Outrigger control system spring Adjustable outrigger of the platform... -
Page 12: Reach Diagram
12 (34) 4.1 Reach diagram Figure 4 - Leguan 50 Access platform reach graph 4.2 Labels and markings Listed below are the labels and markings on the attachment. They must be visible and readable on the equipment. Replace any unclear or missing label. New labels are available via your retailer or contact... -
Page 13: List Of Labels
13 (34) 4.2.1 List of labels A412413 Identification plate and CE –marking A417131 Max allowed load 200 kg A417283 General instructions access platforms A417281 Max. allowed horizontal force and wind speed A417282 Daily inspection... - Page 14 Set always the supports before lifting! Lifting without supports never allowed - DANGER! A420797 Staying under platform is forbidden A417288 Minimum safety distance from live wires 10 A412541 Leguan 50 Marker / hazard warning tape red/white 12 A414307 Emergency lowering valve...
-
Page 15: Label Locations
15 (34) Table 4 - Leguan 50 Access platform - Conversion of localized sign labels Language Sign label A412413 A421165 A420799 A417281 A420798 A412543 A420796 A420797 A412413 A417131 A417283 A417281 A417282 A412543 A417284 A420797 A412413 A412540 A412602 A412542 A416420 A412543 A416828 A417999... -
Page 16: Attaching The Attachment
5. Attaching the attachment The Leguan 50 Access platform is ready to use as delivered. Couple the attachment and its hydraulic hoses to the loader as instructed in this chapter. Follow also the instructions given in the operator’s manual of the loader. - Page 17 If your loader is not listed in Table 1 on page , ask your Avant dealer before using this attachment.
-
Page 18: Fit Rear Outriggers To The Loader
18 (34) 5.2 Fit rear outriggers to the loader With the Leguan 50 Acces platform, an outrigger set is provided, which are to be installed to the loader. The rear outriggers increase the stability of the attachment and prevent tipping over in case of a tire burst. -
Page 19: Fit The Supporting Bracket And The Outriggers
19 (34) 5.4 Fit the supporting bracket and the outriggers To set the top link the outriggers must be set first. Fit the supporting bracket between the access platform and the bracket on the loader boom after the quick coupling plate has been locked, and after the outriggers have been set. -
Page 20: Set The Top Link
5.5 Connecting and disconnecting hydraulic hoses On Avant loaders the hydraulic hoses are connected using the multi connector system. If you have an older model Avant 300-700 series loader with the conventional quick couplers, and you want to change to the multi connector system, contact your Avant dealer or service point for instructions or installation services. - Page 21 21 (34) Keep all fittings as clean as possible; use the protective caps on both the attachment and the loader. Dirt, ice, etc. may make using the fittings significantly more difficult. Never leave the hoses hanging on the ground; place the couplings onto the holder on the attachment.
-
Page 22: Instructions For Use
22 (34) 6. Instructions for use Check the attachment and the operating environment once more before starting to work, and that all obstacles have been removed from the operating area. Quick inspection of the equipment and the operating area before use are parts of ensuring safety and the best performance of the equipment. -
Page 23: Using The Access Platform
23 (34) Risk of crushing - Ensure that the parking brake of the loader is engaged when working near the attachment. Use additional blocks if needed. Whenever possible, lower WARNING the attachment firmly on the ground. 6.2 Using the access platform Transporting the equipment with the loader: Lift the rear support legs sufficiently high for transportation. -
Page 24: Lifting The Platform
24 (34) 6.2.2 Lifting the platform The access platform will not rise, unless the outriggers have been set to a low position, so that the front wheels of the loader will clearly rise off the ground. The parking stand under the platform must be lifted to make it possible to press down the attachment adequately. - Page 25 25 (34) The access platform can be operated when enough weight is applied on the outriggers and the loader auxiliary hydraulics has been locked on with the control lever; the lever locks to its front or side position depending on the loader model.
-
Page 26: Emergency Lowering Of The Platform
6.4 Ending the use of the access platform When finished working with the Leguan 50 Access platform: 1. Lower it on an even and solid surface 2. Adjust the parking stand so that the access platform will stay balanced in upright position. If needed, extra plates may be used under the outriggers. -
Page 27: Storing The Attachment
27 (34) 6.4.1 Storing the attachment Uncouple and store the attachment on level ground. The best way to store the attachment is a place where it is protected from direct sunlight, rain, and extreme temperatures. Avoid leaving the attachment laying directly on the ground. -
Page 28: Maintenance And Service
Other than daily inspections and maintenance, more demanding service and repairing must be left for qualified AVANT service professionals. The nearest service can be found by contacting your local AVANT dealer. Use only original spare parts. ... -
Page 29: Lubrication
Finding any fault means that the hydraulic hose or component must be replaced and the equipment must not be used until it is repaired. Spare parts are available from your nearest AVANT retailer or authorised service point. Leave the repair work to professional service technicians, if you don’t have adequate knowledge and experience about hydraulic assemblies and how to perform the repairing safely. -
Page 30: Warranty Terms
30 (34) 8. Warranty terms Avant Tecno Oy grants a warranty of one year (12 months) from the date of purchase for the attachment it manufactures. The warranty covers repair costs as follows: Work costs are covered, if the repair is not performed at the factory. - Page 31 31 (34)
- Page 32 Hydraulitoiminen henkilönostin; nostokorkeus 5 m; Avant-kuormaajan työlaite Hydraulisk arbetsplattform med 5 m arbetshöjd; arbetsredskap för Avant lastare A34812 Hydraulic access platform with 5 m working height; attachment for Avant loaders 9.1.2023 Ylöjärvi, Finland Jani Käkelä, Toimitusjohtaja / Verkställande direktör /...
Need help?
Do you have a question about the Leguan 50 and is the answer not in the manual?
Questions and answers