Inventory - Grizzly G0526A40 Owner's Manual

Inventory

The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
Box #1 Inventory (Figure 6)
A. Jointer Assembly w/Carriage Mount ........... 1
B. Fence Assembly & Carriage ...................... 1
C. Cutterhead Guard Assembly ...................... 1
D. Belt Guard .................................................. 1
E. Safety Push Blocks .................................... 2
F. Hex Wrench 3mm ....................................... 1
G. V-Belt A36 .................................................. 1
H. Fence Lock Handle .................................... 1
I. Fence Tilt Lever .......................................... 1
J. Open-End Wrenches 8/10, 12/14mm ...1 Ea.
K. T-Handle Torx Wrench
L. T20 Torx Bits .............................................. 5
M. Flat Hd Torx Screws M6-1 x 15 ................... 10
N. Indexable Inserts 15 x 15 x 2.5mm ............ 5
O. Carriage Support Key
P.
Handwheels ................................................ 2
Q. Fixed Handles ............................................ 2
R. Dust Port 4" ................................................ 1
S. Foot Pedal Caster Assembly ...................... 1
Fasteners (Not Shown)
• Hex Bolts ⁄ "-16 x
3
8
• Lock Washers ⁄ " (Jointer/Stand) ............... 3
3
8
• Hex Bolts ⁄ "-18 x 1" (Column) .................. 4
5
16
• Flat Washers ⁄ " (Column) ........................ 4
5
16
• Flat Washer ⁄ " (Fence Lock) .................... 1
1
2
• Locking Jam Nut (Fence Lock) .................. 1
• Flat Washer 5mm (Belt Guard) .................. 1
• Hex Bolt 8-32 x ⁄
3
8
• Hex Bolt ⁄ "-18 x 2" (Foot Pedal) .............. 1
5
16
• Flat Washer ⁄ " (Foot Pedal) ..................... 1
5
16
• Flat Washers ⁄ " (Foot Pedal) .................... 4
3
8
• Hex Nuts ⁄ "-16 (Foot Pedal) ..................... 2
3
8
• Hex Bolts ⁄ "-16 x 2
3
8
Box #2 Inventory (Not Shown)
• Stand Assembly w/Motor ........................... 1
-14-
Qty
⁄ " .......................... 1
1
4
⁄ " x ⁄ " x 9" ........... 1
3 3
8 8
⁄ " (Jointer/Stand) ......... 3
3
4
" (Belt Guard) ................ 1
⁄ " (Foot Pedal) .......... 2
1
2
Qty
A
B
E
G
L
K
P
R
Figure 6. Box #1 inventory.
NOTICE
If you cannot find an item on this list, care-
fully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpack-
ing or they are pre-installed at the factory.
Model G0526A40 (Mfd. Since 12/22)
C
D
F
J
H
I
M
N
O
Q
S