Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Balcrank GIANT JET 1130-008
Summary of Contents for Balcrank GIANT JET 1130-008
- Page 1 SERVICE BULLETIN SB1012 Rev. I 2/05 ® GIANT JET SERIES PUMP ™ 10:1 Model #1130-008 5:1 Model #1130-009 10:l Model #1130-023* *With EPDM Seals Thoroughly read and understand this manual before installing, operating or servicing this equipment. OPERATION, INSTALLATION, MAINTENANCE AND REPAIR GUIDE...
-
Page 2: General Safety
General Safety WARNING: This pump develops 1500 PSI (103.4 BAR) maximum working Thoroughly read and understand this manual pressure at 150 PSI (10.3 BAR) before installing, operating or servicing this maximum inlet air pressure and stall equipment. conditions. Be sure that any components Guide to Safety Comments: or accessories used in the system are rated to withstand this pressure. -
Page 3: Product Description
It has a simple yet durable construction with all internal parts lubricated at the factory using a life-tested synthetic grease (Balcrank p/n 826733). This grease coats all internal parts and repels air line moisture to inhibit corrosion. -
Page 4: Pump Installation
If mounting to a reservoir bung port, thread a special synthetic grease at initial assembly the pump bung adapter into the bung thread (available as Balcrank p/n 826733) and does on the fluid reservoir, lower the pump into not require additional greasing except during the mounted bung adapter, then tighten. -
Page 5: Pump Operation
The air motor and the housing o-ring (11) can now be serviced. Reassemble in reverse 5. Use the air regulator to control the pump’s order, being sure to use grease (Balcrank p/n speed and cycle rate. Always use the lowest 826733) on all seals and o-rings. - Page 6 Reassemble in reverse order, being sure to pump, the solenoid, or any part of the system. use grease (Balcrank p/n 826733) on seal (15) to ease reassembly. 1. Disconnect the air supply from the pump.
-
Page 7: Troubleshooting Guide
Troubleshooting Guide NOTE: Check all other possible causes before disassembling pump. CAUTION: Before servicing, reduce fluid supply pressure to zero. n i l n i l . c t u l f , l l i . c t c i t n i l , l l i l f f... -
Page 8: Parts List
Parts List Giant Jet Stub Pump, 10:1 Ratio ™ Model 1130-008 (* is for Model 1130-023 only) ITEM PART # DESCRIPTION PART PAK PUMP KIT QTY PART PAK MODEL 900001 900002 820234 Bale Hook Lift 820235 Drive Screw 90001Q12 819514 Nut 817308 Packing 90002Q09 819513 U-Washer... - Page 9 Exploded View Giant Jet Stub Pump, ™ C1 CONNECTOR 10:1 Ratio Model 1130-008 Refer to air motor detail on page 10.
-
Page 10: Air Motor
Air Motor Giant Jet™ Stub Pump, All Models One Full Turn From Tight... - Page 11 Parts List Air Motor Giant Jet Stub Pump, ™ All Models PART PAK PUMP KIT QTY PART PAK ITEM PART # DESCRIPTION MODEL 900001 900002 819508 Spring 90012Q04 819510 817308 Packing 90002Q09 825749 Sleeve 819503 Stem 819496 Flange Nut 90013Q04 812433 Stop Nut 90014Q04...
- Page 12 It is imperative that any grease removed rod (30) with spanner wrench and use a spanner during maintenance be replaced afterwards. wrench to remove fluid piston nut (25). Inspect Contact your local Balcrank distributor, ® the fluid piston ball (4), spring (21), quad ring...
-
Page 13: Exploded View
Exploded View Giant Jet Pump, ™ 5:1 Ratio 1130-009... - Page 14 Parts List Giant Jet Pump, ™ 5:1 Ratio 1130-009 Item Part Description 827932 Air Motor Not Used 806907 O-Ring, Buna-N* 806962 Ball 808667 Gasket* 808691 Ball 817308 Packing 819487 819511 Stop 819512 Washer, Nylon* 819513 Washer 819514 820234 Bale 820235 Drive Screw 822365 Bearing*...
- Page 15 NOTES: Quality Checklist Bill of Material checked for current content. Pump was tested and met Balcrank performance standards. ® I ________________________________________ certify that this product meets or exceeds Balcrank's high quality standards. Revision Log: Rev. H - added Model 1130-023 & EPDM seals...
-
Page 16: Warranty
Warranty Service Claim number ® (WSC#) clearly marked on the outside of the carton. Balcrank’s sole responsibility is for defects in material and workmanship, and Buyer’s sole and exclusive remedy hereunder, shall be limited to repair or replacement of the defective part or equipment.
Need help?
Do you have a question about the GIANT JET 1130-008 and is the answer not in the manual?
Questions and answers