Page 1
Glīon Dolly XL Electric Scooter User Manual 12/15/2022...
Page 2
Manual. The website also provides videos demonstrating how to fold, unfold, and operate the scooter. Your Glion Electric Scooter is covered by a warranty. For the specifics of this warranty, visit our website at www.getglion.com. Please register your Glion Electric Scooter at www.getglion.com...
GLION MODEL 255 SPECIFICATIONS ......................... 6 GLION MODEL 255 PARTS DIAGRAM ......................... 7 UNFOLD/FOLD INSTRUCTIONS ............................ 8 OVERVIEW OF YOUR GLION ELECTRIC SCOOTER ....................11 OPERATING YOUR GLION ELECTRIC SCOOTER ....................14 BATTERY AND CHARGER .............................. 15 DOLLY FEATURE ................................17 SCOOTER COVER (OPTIONAL ACCESSORY) ......................
SAFETY SPECIFICATIONS AND OWNER OBLIGATIONS 1. LEGAL RIDING LOCATIONS: Always check and obey local laws or regulations, which govern where you can legally operate the scooter. Only operate the scooter where legally permitted, and do so with caution. The scooter can only be operated on private property unless it is street legal in your jurisdiction.
Page 5
8. GUEST USE: Never permit a guest to use this scooter unless the guest has read the user manual and all the warnings. Always provide a guest with helmet, elbow pads, and knee pads before permitting the guest to operate the scooter. Never allow more than one person at a time to ride the scooter.
Page 6
17. SURFACE CONDITIONS: The scooter is intended for use on hard, flat, dry paved surfaces without loose debris such as sand, leaves, rocks or gravel. Wet, slick, bumps, uneven or rough surfaces may impair traction and contribute to possible accidents. Do not ride your scooter in mud, gravel, sand, ice, or water.
For video instructions, please visit our website at www.getglion.com. We encourage you to view the video instructions prior to unfolding/folding operation to avoid damage to your Glion scooter. UNFOLDING YOUR SCOOTER: For shipping safety, the bottle holder is taken off and included in the package. Instructions for installing the bottle holder is included below in step 4.
Page 10
Step 3. Pull down the collar on the handlebar to release the collar lock. Lift the handlebar grips until the left and right t-bar collars (C) snap into place and the handle grips are locked in the operating position. Step 4. Install the bottle holder using the Allan wrench and screws included in the package on the vertical handle bar.
Page 11
Button Make sure you need to firmly press it in order to close Step 6 . Press the handlebar retract positioning button and raise the handlebar to the desired height. Tightly close the quick release lever (D). Make sure the quick release lever is securely tightened.
Step 4. Fold down the handlebar until you hear a click and the folding mechanism locks into the folded position. OVERVIEW OF YOUR GLION ELECTRIC SCOOTER WARNING: For your safety, please take the time to familiarize yourself with the handlebar controls and with its movements and balance before attempting to ride your scooter with the motor engaged.
Page 13
1. Powering On/Off: To turn the scooter on or off, you must press and hold for about 2 seconds the on/off switch in the middle of the LCD as shown below (F). The LCD display is lit when the power is on and dark when off. The scooter will automatically turn off after five minutes of non-use.
Page 14
M button once will show single trip mileage – distance traveled since the scooter is turned move at a constant 2mph speed. Release the button to stop Walking Mode. Short press the on. Turning off the scooter power will reset the single trip mileage back to zero. Short pressing the M button again will show the battery voltage.
IT IS YOUR RESPONSIBILITY TO MAINTAIN CONTROL OF YOUR SCOOTER AT ALL TIMES! OPERATING YOUR GLION ELECTRIC SCOOTER Getting Ready: 1. Fully charge the battery. For safety reasons, the battery is only 80% charged when shipped from the factory (See Page 16 Battery Charging Instructions Below).
PROPELLING THE SCOOTER. THEN FOLLOW BELOW INSTRUCTIONS AND TRY RIDING IT POWERED ON WITH THE SPEED SETTING AT DEFAULT ECO LEVEL. Riding the Scooter Powered: 1. Raise the kickstand. 2. Press and hold the power button about two seconds to turn on the scooter. The LCD screen should be lit when the scooter is turned on.
Page 17
6. Use only the charger supplied with this scooter or a recommended replacement specified by Glion. 7. Charger supplied by Glion is Model No. HP1202L3(90w), manufactured by High Power Technology (KunShan) Inc. Operating temperature is 0℃ (32° F) ~ 40℃ (104°...
1. Turn the scooter off. The charge port (K) is located on the right side of the neck of the scooter above the folding mechanism. Open the charge port rubber protective cover and securely plug the charger into the charge port. 2.
SCOOTER COVER (OPTIONAL ACCESSORY) 1. Cover Installation and Removal Fold your Glion Electric Scooter and place it horizontally on the floor and drape the cover over the front tire and across the scooter. Pull the bottom of the cover over the T-bar so the cover now extends from the front tire on one side to the bottom of the T-bar on the other side.
Page 20
To Remove the Scooter Cover Reverse the Installation Steps. 2. Helmet Pocket and Handlebar Carrying Access The scooter cover has a side pocket allowing rider to store helmet as shown above. The scooter cover also has two slits in the side so you can easily carry the scooter holding the lower handlebar downtube.
3. Cover Storage Pouch the retractable handle and carefully reverse the pouch so you can see the pouch’s Glion logo. Stuff The scooter cover also serves as a storage pouch for the cover. The cover can be stuffed into a the scooter cover inside of the pouch.
Aucune des pièces ne peut être réparée par l’utilisateur BATTERY DISPOSAL: Your Glion product uses lithium ion batteries, which must be recycled or disposed of in an environmentally safe manner. Do not dispose of a lithium ion battery in a fire. The battery may explode.
Page 23
Connector Not tight Align arrow icons from both sides Tight A: Neck wire main connector: There are 2 connectors located inside of the wrapping material near the neck area. You need to first unwrap it to expose the connectors. Starting from behind the lower headlight where the wiring comes out of the lower connector.
Page 24
arrow icons on both sides of the connector and firmly connect them. Make sure it is fully seated and tight. There is another smaller connector along this wiring near the neck. That is for the charging port. If the scooter battery is not taking charges, this connector may need to be checked.
PRODUCT REGISTRATION We encourage you to register your Glion Electric Scooter with us. Registration helps us ensure your continued satisfaction and enables us to contact you with new product instructions. Also, registration and proof of purchase are necessary to make a warranty claim. Please register your...
GLION LIMITED WARRANTY Your Glion Electric Scooter is covered by a warranty. For the specifics of this warranty, visit our website at www.getglion.com. (“Probity Cell”) BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL OR UNDER NO CIRCUMSTANCES SHALL PROBITY CELL LLC, DBA GLION®...
Need help?
Do you have a question about the Dolly XL and is the answer not in the manual?
Questions and answers