Subscribe to Our Youtube Channel
Related Manuals for Boser HS-5010
Summary of Contents for Boser HS-5010
- Page 1 HS-5010 ® Pentium VGA I.S.B. Full Size Triton VX All-in-one PICMG Bus Industrial Single Board Computer...
- Page 2 Trademarks BOSER is a registered trademark of BOSER Technology Co., Ltd. Award is a registered trademark of Award Software, Inc. ISB is a registered trademark of BOSER Technology Co., Ltd.
-
Page 3: Table Of Contents
Contents HS-5010........................1 INTRODUCTION ..............錯誤! 尚未定義書籤。 1.1 S ......................4 PECIFICATIONS ............. 錯 誤 ! 尚 未 定 義 書 籤 。 1.2 W HAT YOU HAVE INSTALLATION......................6 2.1 HS-5010' ....................6 AYOUT !! ..............錯 誤 ! 尚 未 定 義 書 籤 。... - Page 4 AWARD BIOS SETUP....................22 4.1 M ......................23 4.2 S CMOS S ..................24 TANDARD ETUP 4.3 BIOS F ..................25 EATURES ETUP 4.4 C ..................26 HIPSET EATURES ETUP 4.5 I ..................27 NTEGRATED ERIPHERALS 4.6 P ................28 OWER ANAGEMENT ETUP ii ?Contents...
-
Page 5: Introduction
Chapter-1 Introduction The HS-5010 is an all-in-one full-size card with a full features in a small package for the industrial applications. The Intel VX chipset provides major core logic, in addition to the support for various CPU, it also includes Intel MMX. - Page 6 1.1 Major Features CPU：Intel Pentium CPU 75~233MHz, AMD K5、K6, Cyrix M2, 6x86 or Intel MMX; Socket 7 ZIF socket. Bus Interface：PCI/ISA Bus; Comply to PICMG standard. Chipset：Intel Triton VX chipset. Data Bus：64bit. Processing Ability：64bit. VGA Controller ： S3 86C775 chipset with 2MB memory, support resolutions up to 1280 x 1024 256u colors, reserved internal 10pin VGA connector.
-
Page 7: Specifications
Max. Power Requirement：+5V@6A, +12V/-12V power supply. Operating Temperature：0~55°C（CPU needs a cooler）. Dimension：13.26”（L）x 4.8”（W）（337mm x 122mm）. 1.2 What do you have The HS-5010 package includes the following items： HS-5010 Industrial Single Board Computer. Printer port flat cable. IDE port flat cable. -
Page 8: Hs-5010' S Layout
2.1 HS-5010’ s Layout... -
Page 9: Installation
Do this only when the board is placed on a anti-static’s firm and lat surface. Note： DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN DAMAGED. You are now ready to install your HS-5010 Industrial Single Board. -
Page 10: Jumper Description
2.3 Jumper Description This board’s default jumpers are present at the factory. If you want to change the HS-5010’s configuration, please follow the instructions. A jumper switch is closed （sometimes referred to as shorted with a plastic cap inserted over two pins of the jumper）. A jumper is open with a plastic cap inserted over one or no pin of the jumper. -
Page 11: Setting The Cpu
2.4 Setting the CPU All CPU Card provides all possibility in jumper setting for wide using all types of CPU with JP6, JP8, JP9, JP10, JP12, JP13, JP14 and JP15 setting in following. The JP9, JP12, JP13 sets the multi-times ratio of the CPU’s specification. Please reference to the following table for all type CPU in used. - Page 12 CPU Voltage Selection The HS-5010 provides all necessary setting for the all CPU operating. User may selected from 2.8V to 3.5V. CPU Voltage 2.8V *2.9V 3.2V All Open 3.3V 3.5V （*）：default setting CPU Clock-in Select JP10 50MHz 1-2, 3-4 55MHz...
- Page 13 Refresh Based JP14 60MHz *66MHz （*）：default setting Sysclk Configuration JP15 Divided by 4 *Divided by 3 （*）：default setting...
-
Page 14: System Memory Dram（Edo Ram Supported
16MB, or 32MB memory modules. The total capacity of on board memory are between 2MB to 128MB. The HS-5010 requires at least 2pcs of the RAM modules on SIMM sockets SM1/SM2 or SM3/SM4 or 1pcs SDRAM module. 2.6 Watch-Dog Timer The Watch-Dog Timer is enabled by reading the port 443H. - Page 15 When the power of HS-5010 is turned on, the Watch-Dog Timer is disabled. The Watch-Dog Timer can be enabled by reading the Watch-Dog Timer enable/refresh control port（443H）and disabled by reading the Watch-Dog Timer disable control port（43H）. After the Watch-Dog Timer is enabled, the user must constantly refresh the Watch-Dog Timer by reading the Watch-Dog Timer enable/refresh port （443H）...
- Page 16 AL,DX ; get back AX, DX...
-
Page 17: Diskonchip Address Setting
2.7 VGA Controller The HS-5010 has built-in a S3 VGA Controller. If you want to use the external VGA Card, the BIOS will automatically disable the on board VGA Controller and use the external one. Video Modes S3 86C775 Chipset with 2MB memory, support resolutions up to 1280 x 1024 256 colors, reserved internal 10pin VGA connector. -
Page 18: Connection
Chapter-3 Connection This chapter describes how to connect the peripherals, switches and indicators to the HS-5010 board. 3.1 Floppy Disk Drive Connector HS-5010 board is equipped with a 34pin daisy-chain driver connector cable. CN6 : FDD Connector PIN NO. DESCRIPTION PIN NO. -
Page 19: Pci E-Ide Drive Connector
3.2 PCI E-IDE Drive Connector The HS-5010 has on board IDE interface. It can be connected up to four IDE(Integrated Device Electronics) hard disk drives to the HS-5010 IDE controller. CN3(IDE 1)：Primary IDE Connector CN4(IDE 2)：Secondary IDE Connector CN3/CN4 : IDE Interface Connector PIN NO. -
Page 20: Parallel Port
3.3 Parallel Port The HS-5010 includes an on board parallel port which accesses through a 26pin flat cable connector CN5. CN5 : Parallel Port Connector PIN NO. DESCRIPTION PIN NO. DESCRIPTION STROBE DATA 0 DATA 1 DATA 2 DATA 3... -
Page 21: Keyboard Connector
CN7 : Serial Port 10pin Header PIN NO. Description PIN No. Description 3.5 Keyboard Connector The HS-5010 provides two keyboard connector. CN1 : 5pin Header Keyboard Connector PIN NO. Description Keyboard Clock Keyboard Data Ground CN13 : 6pin Mini-din Keyboard Connector PIN NO. -
Page 22: External Switches And Indicators
Ground JP3 : IDE LED Connector PIN NO. Description HDD Active# 3.7 External Speaker The HS-5010 has its own buzzer, and JP2 allows user to connect to the external speaker. JP2 : Speaker Connector PIN NO. Description Speaker Signal Ground... -
Page 23: 6-Pin Mini Din Ps/2 Mouse Connector
3.8 6-pin Mini Din PS/2 Mouse Connector The HS-5010 has a PS/2 mouse on board which uses IRQ12. If you do not use the PS/2 mouse and wish to assign IRQ12 for other purposes, you may change JP16 to disconnect PS/2 interrupt from IRQ12. -
Page 24: Usb Ports Connector
Ground Green Ground Blue Ground HSYNC Ground VSYNC Ground 3.12 IR Connector The HS-5010 provides a 5-pin internal IR communication connector. The JP24 provides for IrDA 1.0 specification application. JP24 : 5-pin IR Connector PIN NO. Description IRRX Ground IRTX... -
Page 25: Award Bios Setup
Chapter-4 AWARD BIOS Setup The HS-5010 uses the Award PCI/ISA BIOS for the system configuration. The Award BIOS setup program is designed to provide the maximum flexibility in configuring the system by offering various options which could be selected for end-user requirements. This chapter is written to assist you in the proper usage of these features. -
Page 26: Main Menu
4.1 Main Menu Once you enter the Award BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to select among the items and press ＜Enter＞... -
Page 27: Standard Cmos Setup
4.2 Standard CMOS Setup The Standard Setup is used for the basic hardware system configuration. The main function is for Data/Time and Floppy/Hard Disk Drive settings. Please refer to the following screen for the setup. When the IDE hard disk drive you are using is larger than 528MB, please set the HDD mode to LBA mode. -
Page 28: Bios Features Setup
4.3 BIOS Features Setup This section allows you to configure your system for the basic operation. You have the opportunity to select the system’s default speed, boot up sequence, keyboard operation, shadowing and security. ROM PCI/ISA BIOS (2A59GD3G) BIOS FEATURES SETUP AWARD SOFTWARE, INC. -
Page 29: Chipset Features Setup
4.4 Chipset Features Setup This section allows you to configure the system based on the specific features of the installed chipset. This chipset manages bus speeds and the access to the system memory resources, such as DRAM and the external cache. It also coordinates the communications between the conventional ISA and PCI buses. -
Page 30: Integrated Peripherals
4.5 Integrated Peripherals The IDE hard drive controllers can support up to two separate hard drives. These drives have a master/slave relationship which is determined by the cabling configuration used to attach them to the controller. Your system supports two IDE controllers--a primary and a secondary--so you can install up to four separate hard disks. -
Page 31: Power Management Setup
4.6 Power Management Setup The Power Management Setup allows user to configure the system for saving energy in a most effective way while operating in a manner consistent with his own style of computer use. ROM PCI/ISA BIOS (2A59GD3G) POWER MANAGEMENT SETUP AWARD SOFTWARE, INC.
Need help?
Do you have a question about the HS-5010 and is the answer not in the manual?
Questions and answers