Related Manuals for Dahua PSDW5631S-B360
Summary of Contents for Dahua PSDW5631S-B360
- Page 1 Multi-Sensor Panoramic Network Camera Quick Start Guide ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD. V1.0.1...
-
Page 2: Foreword
Quick Start Guide Foreword General This manual introduces the functions, installation and operations of the camera. Safety Instructions The following categorized signal words with defined meaning might appear in the manual. Signal Words Meaning Indicates a medium or low potential hazard which, if not avoided, WARNING could result in slight or moderate injury. - Page 3 Quick Start Guide Please visit our website, contact the supplier or customer service if there is any problem occurring when using the device. If there is any uncertainty or controversy, we reserve the right of final explanation. ...
-
Page 4: Important Safeguards And Warnings
Quick Start Guide Important Safeguards and Warnings Electrical Safety All installation and operation should conform to your local electrical safety codes. The power source shall conform to the Safety Extra Low Voltage (SELV) standard, and supply power with rated voltage which conforms to Limited Power Source requirement according to IEC60950-1. - Page 5 Quick Start Guide It is recommended to ground the device to enhance reliability. Do not touch the image sensor directly (CMOS). Dust and dirt could be removed with air blower, or you can wipe the lens gently with soft cloth that moistened with alcohol. Device body can be cleaned with soft dry cloth, which can also be used to remove stubborn ...
-
Page 6: Table Of Contents
Quick Start Guide Table of Contents Foreword ................................I Important Safeguards and Warnings ......................III 1 Introduction ..............................1 Device Ports ....................................1 Connecting Alarm Input/Output ............................2 2 Network Configuration ..........................4 Initializing Device ..................................4 Modifying Device IP Address ..............................5 Logging in to Web Interface.............................. -
Page 7: Introduction
Quick Start Guide Introduction Device Ports Device ports might vary with different models, and the actual product shall prevail. Do waterproof to all the cable joints with insulating tape and waterproof tape to avoid short circuit and water damage. For the detailed operation, see the FAQ manual. Figure 1-1 Device ports For more information about device ports, see Table 1-1. -
Page 8: Connecting Alarm Input/Output
Quick Start Guide Port Name Function SD card slot. Audio output Connects to speaker to output audio signal. RESET Press and hold the button for 10 s to reset the camera. Connecting Alarm Input/Output Alarm input/output is available on select models. Step 1 Connect alarm input device to the alarm input end of the I/O port. - Page 9 Quick Start Guide Figure 1-4 Mode B Step 3 Log in web interface, and configure alarm input and alarm output in alarm setting. The alarm input in the web interface is corresponding to the alarm input end of the I/O ...
-
Page 10: Network Configuration
Quick Start Guide Network Configuration Device initialization and IP address setting can be finished with the "ConfigTool" or in web interface. For more information, see the WEB operation manual. Device initialization is available on select models, and it is required at first use or after the device ... -
Page 11: Modifying Device Ip Address
Quick Start Guide Select the devices that need initialization, and then click Initialize. Step 6 The password setting interface is displayed. See Figure 2-2. Figure 2-2 Password setting Step 7 Set and confirm the password of the devices, then enter a valid email address, and then click Next. -
Page 12: Logging In To Web Interface
Quick Start Guide The Modify IP Address interface is displayed. See Figure 2-3. Figure 2-3 Modify IP Address Select Static mode, and then enter start IP, subnet mask, and gateway. Step 3 IP addresses of multiple devices will be set to the same if you select the Same IP ... - Page 13 Quick Start Guide Figure 2-4 Main interface...
-
Page 14: Installation
Quick Start Guide Installation Packing List The tool required for the installation such as electric drill is not provided in the packing. The operation manual and related tool are contained in the disk or the QR code, and the actual ... -
Page 15: Installing Device
Quick Start Guide Installing Device 3.3.1 Installation Type 3.3.2 Installing SD Card (Optional) Pull the power plug off before installing or removing the SD card. -
Page 16: Attaching Device
Quick Start Guide 3.3.3 Attaching Device Make sure the mounting surface is strong enough to hold at least three times of the weight of the device and bracket. Cable going through the mounting surface... - Page 17 Quick Start Guide Cable going through the side cable tray...
- Page 18 Quick Start Guide...