Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Dahua Pro Series
Summary of Contents for Dahua Pro Series
- Page 1 Thermal Network Bullet Camera Quick Start Guide V1.0.1...
-
Page 2: Regulatory Information
Regulatory Information The regulatory information herein might vary according to the model you purchased. Some information is only applicable for the country or region where the product is sold. FCC Information Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. -
Page 3: Foreword
Foreword General This Quick Start Guide (hereinafter referred to be "the Guide") introduces the functions, installation and operations of the camera. Safety Instructions The following categorized signal words with defined meaning might appear in the Guide. Signal Words Meaning Indicates a medium or low potential hazard which, if not avoided, could result in slight or moderate injury. - Page 4 The Guide is for reference only. If there is inconsistency between the Guide and the actual product, the actual product shall prevail. We are not liable for any loss caused by the operations that do not comply with the Guide. ...
-
Page 5: Important Safeguards And Warnings
Important Safeguards and Warnings This chapter describes the contents covering proper handling of the device, hazard prevention, and prevention of property damage. Read these contents carefully before using the device, comply with them when using, and keep it well for future reference. Installation and Maintenance Professionals Requirements All the installation and maintenance professionals must have qualification certificate or experiences of installing and maintaining CCTV system, electric apparatus in the explosive gas... - Page 6 Please don’t block the ventilation opening near the device, which is to avoid heat accumulation for the device. Please don’t install the device near the place with heat source, such as radiator, heater, stove or other heating equipment, which is to avoid fire. Please don’t aim the lens at intense radiation source directly (such as sun, laser and ...
- Page 7 Around 2.5m long control cable is reserved when the device is delivered out of factory, it should use explosionproof flexible tube or armor cable to protect when the control cable is connected to the explosionproof control cabinet. Please cut off power before device maintenance and overhaul. It is prohibited to open the cover with power on in the explosion environment.
-
Page 8: Cybersecurity Recommendations
Cybersecurity Recommendations Cybersecurity is more than just a buzzword: it’s something that pertains to every device that is connected to the internet. IP video surveillance is not immune to cyber risks, but taking basic steps toward protecting and strengthening networks and networked appliances will make them less susceptible to attacks. - Page 9 Enable Account Lock The account lock feature is enabled by default, and we recommend you to keep it on to guarantee the account security. If an attacker attempts to log in with the wrong password several times, the corresponding account and the source IP address will be locked. Change Default HTTP and Other Service Ports We suggest you to change default HTTP and other service ports into any set of numbers between 1024~65535, reducing the risk of outsiders being able to guess which ports you...
- Page 10 14. Construct a Safe Network Environment In order to better ensure the safety of equipment and reduce potential cyber risks, we recommend: Disable the port mapping function of the router to avoid direct access to the intranet devices from external network. The network should be partitioned and isolated according to the actual network needs.
-
Page 11: Table Of Contents
Table of Contents Regulatory Information ..........................I Foreword ..............................II Important Safeguards and Warnings ....................IV Cybersecurity Recommendations ......................VII 1 Unpacking the Box ..........................1 2 Design ..............................2 Dimensions ........................... 2 Cable ............................. 2 3 General Configuration .......................... 4 Initializing Camera ........................ -
Page 12: Unpacking The Box
Unpacking the Box Refer to the following checklist and check the package. If you find device damage or any loss, contact the after-sales service. Figure 1-1 Checklist Unpacking the Box 1... -
Page 13: Design
Design Dimensions Figure 2-1 Dimensions (mm [inch]) Cable Cable type might vary with different cameras, and the actual product shall prevail. Figure 2-2 Cable ports Please refer to Table 2-1 for more details about the cable function. Table 2-1 Cable ports description Port Port Name Connector Function Description... - Page 14 Port Port Name Connector Function Description — I/O port Alarm signal input/output. Input 12V DC. Power input — POWER port Actual use shall be in accordance with device label instruction. Otherwise, it may cause damage to the device. RS485_A (Yellow) RS-485 port, control external PTZ and so —...
-
Page 15: General Configuration
General Configuration Initializing Camera You need to initialize your Camera and set the user password when logging in for the first time. You can use web or ConfigTool to achieve initialization. Here initialization by web is taken as an example. It fails to use the Camera if the Camera is not initialized. -
Page 16: Modifying Ip Address
In order to reset password, input email address properly and update in Email Address time. Step 3 Click Save to finish initialization. Modifying IP Address In order to make the camera get access to network, please plan IP address reasonably according to the actual network environment. - Page 17 It will prompt you to install plug-in for the first system login, please save and install plug-in according to prompt. The web interface will refresh automatically after plug-in installation is completed, then live video will show up. Figure 3-3 The live interface General Configuration 6...
-
Page 18: Installation
Installation Make sure the mounting surface is strong enough to hold at least eight times of the camera weight. The following figure is for reference only, and the actual product shall prevail. Cable Preparation Selecting Needed Video Cable ... -
Page 19: Installing Camera
Installing Camera 4.2.1 (Optional) Installing SD Card Please cut off the device power before installing SD card. Be cautious and do not mistake Micro SD card slot for reset hole. Long press the reset button for 4 seconds–5 seconds and you will reset your Camera. Please check if the waterproof ring is installed properly before closing the cover, otherwise, ... -
Page 20: Fixing Camera
4.2.2 Fixing Camera Figure 4-2 Fixing camera 4.2.3 Connecting Cable Ports Refer to “2.2 Cable” and connect each cable port to corresponding cables. Then use the insulting tape to seal each port to prevent water leakage. Installation 9... -
Page 21: Installing Waterproof Connector
4.2.4 Installing Waterproof Connector Figure 4-3 Installing waterproof connector for network port 4.2.5 Adjusting Sun Shield Cover Figure 4-4 Adjusting sun shield cover Installation 10... -
Page 22: Adjusting Camera
4.2.6 Adjusting Camera Please make sure the adjusting screw is loosened when adjusting device direction and monitoring angle. Tighten the adjusting screw firmly after adjustment is completed. Please do not rotate the device body over 360°when the device body and mounting pedestal form an angle of 90°and the adjusting screw is firmly tightened. -
Page 23: Configuring Alarm
Configuring Alarm It has to cut off power first when connecting cables. Alarm Input and Output Connection Description Step 1 Connect alarm input device to alarm input port of I/O cable. Step 2 Connect alarm output device to alarm output port of I/O cable. Alarm output is relay switch output, and the alarm output port can only be connected to NO alarm device. - Page 24 Alarm output: port ALARM_OUT and ALARM_COM form a switch, which can be used to provide alarm output. Normally the switch is on, and the switch will be off when there is alarm output. Figure 5-3 Alarm output Configuring Alarm 13...
-
Page 25: Appendix 1 Lightening And Surge Protection
Appendix 1 Lightening and Surge Protection This series bullet camera adopts TVS lighting protection technology. It can effectively prevent damages from various pulse signals below 6000V, such as sudden lighting and surge. While maintaining your local electrical safety code, you still need to take necessary precaution measures when installing the Camera in the outdoor environment. - Page 26 Appendix figure 1-1 Lightening protection Lightening and Surge Protection 15...