Subscribe to Our Youtube Channel
Related Manuals for Dahua LS460UCM-EF
Summary of Contents for Dahua LS460UCM-EF
- Page 1 LCD Video Wall User’s Manual User’s Manual User’s Manual User’s Manual User’s Manual V1.0.0 V1.0.0 V1.0.0 V1.0.0 V1.0.0...
-
Page 2: Foreword
Foreword General This manual introduces the maintenance and confuguration of the LCD Video Wall (hereinafter referred to as "the Video Wall"). Safety Instructions The following categorized signal words with defined meaning might appear in the manual. Signal Words Meaning Indicates a high potential hazard which, if not avoided, will result in DANGER death or serious injury. - Page 3 format) cannot be opened. All trademarks, registered trademarks and the company names in the manual are the properties of their respective owners. Please visit our website, contact the supplier or customer service if there is any problem occurring when using the device. If there is any uncertainty or controversy, we reserve the right of final explanation.
-
Page 4: Important Safeguards And Warnings
Important Safeguards and Warnings The manual helps you to use our product properly. To avoid danger and property damage, read the manual carefully before using the product, and keep it well for future reference. Operating Requirements Do not place or install the Video Wall in a place exposed to sunlight or near the heat source. ... -
Page 5: Table Of Contents
Table of Contents Foreword ..............................I Important Safeguards and Warnings ....................... III 1 Maintenance ............................1 1.1 Environmental Requirement ......................1 1.2 Maintenance Tips ........................... 1 2 Packing List............................4 3 Device Introduction ..........................5 3.1 LCD Video Wall ..........................5 3.2 Port ............................... -
Page 6: Maintenance
Maintenance 1.1 Environmental Requirement The video wall can only be installed indoors. It is recommended that the room where the video wall is installed be equipped with air conditioner. The video wall cannot be operated in environment with high humidity and heavy dust. Do not block the vent of the video wall and the airflow around it;... - Page 7 Temperature, Humidity and Ventilation The appropriate ambient temperature range for the video wall is 22°C±4°C, and the appropriate relative humidity range is 30%–70%, no condensation. There must be no great temperature and humidity difference. If the video wall is used in environment with high temperature and humidity, there will be tiny ...
- Page 8 Power Supply Stable 100V–240V single phase power supply is needed; otherwise the video wall cannot work normally. To get stable voltage and prevent damage result from electrical surge, use the stabilized voltage supply. Storage Requirement If the video wall is not in use for a long time, cover it with the dust-cloth. ...
-
Page 9: Packing List
Packing List Check Table 2-1 to see whether the components are complete. The appearance, items, or quantity might be different depending on the model that you purchased, and the actual packing list shall prevail. Table 2-1 Packing list Component Quantity Liquid crystal video wall AC power cable HDMI cable... -
Page 10: Device Introduction
Device Introduction 3.1 LCD Video Wall The LCD video wall is displayed in Figure 3-1. Figure 3-1 LCD video wall 3.2 Port Ports are displayed in Figure 3-2. For detailed parameters, see Table 3-1. Figure 3-2 Port Table 3-1 Port description Port Function Power input port... -
Page 11: Remote Control
Port Function CVBS input Inputs CVBS signals. CVBS output Outputs CVBS signals. VGA in Inputs VGA signals. VGA out Outputs VGA signals. DVI in Inputs DVI signals. HDMI in Inputs HDMI signals. HDMI out 1 Outputs HDMI signals. HDMI out 2 Outputs HDMI signals. - Page 12 Picture Name Function Left and right direction button: Use direction buttons to select items on the left or right of the current parameter on the screen (if you have selected voice, Direction you can use these buttons button to adjust the volume). Up and down direction button: Use it to select items up or...
-
Page 13: Interface Configuration
Interface Configuration Use the remote control to configure parameters for the video wall. Press the menu button, the menu of the video wall is displayed in Figure 4-1. Figure 4-1 Menu For introductions of icons on the interface, see Table 4-1. Table 4-1 Icon description Icon Description... -
Page 14: Picture
4.1 Picture Press Menu on the remote control, the menu interface is displayed on the video wall. The default menu bar is Picture menu bar. Figure 4-2 Picture 4.1.1 Image Mode You can adjust the overall effects of images through image mode. Step 1 Press Menu on the remote control. -
Page 15: Contrast
4.1.2 Contrast You can adjust the luminance or color of images to make objects in images distinguishable by adjusting contrast. Step 1 Select Image > Contrast. Figure 4-4 Contrast Step 2 Adjust the contrast by the left and right buttons on the remote control according to your requirement. -
Page 16: Sharpness
Step 1 Select Image > Saturability. Figure 4-6 Saturability Step 2 Adjust the Saturability by the left and right buttons on the remote control according to your requirement. The range of saturability is 0–100. 4.1.5 Sharpness Definition of images can be adjusted by adjusting sharpness. The higher the sharpness is, the clearer the images are, and image noise might occur. -
Page 17: Aspect Ratio
Figure 4-8 Color temperature Step 2 Adjust color temperature by the left and right buttons on the remote control according to your requirement. Color temperature has four types: cool, standard, warm, and personal. Only in user mode can you adjust the value of red, green, and blue. ... -
Page 18: Noise Reduction
PointToPoint Point to point display. Different signal modes have different zoom modes. Step 3 Press Menu on the remote control to complete the setting. 4.1.8 Noise Reduction To improve quality of images, adjust the noise reduction. Only in CVBS signal mode can you select image noise deduction function. Step 1 Select Image >... - Page 19 Figure 4-11 Geometry (VGA) H-Position H-Position is used to adjust the horizontal position of the video wall. Step 1 On the Geometry menu, select H-Position. Figure 4-12 H-position Step 2 Adjust the horizontal position by the left and right buttons on the remote control according to your requirement.
- Page 20 Figure 4-13 V-Position Step 2 Adjust the vertical position by the left and right buttons on the remote control according to your requirement. Sampling Frequency Sampling frequency is the number of samples per second taken from a continuous signal. The higher the frequency, the more accurate the signals are.
-
Page 21: Sound
Figure 4-15 Phase Step 2 Adjust phase by the left and right buttons on the remote control according to your requirement. Auto Adjust The position of video wall can be automatically adjusted. Step 1 On the Gemetry menu, select Auto Adjust. Figure 4-16 Auto adjust Step 2 Press Menu on the remote control, and then the position of the screen will be automatically adjusted. -
Page 22: Advanced
Figure 4-17 Sound Step 2 Select Sound > Sound Adjust. Figure 4-18 Sound adjust Step 3 Adjust the on and off status of the sound adjust by the left and right buttons on the remote control. If you select off, then the video wall is in silent mode. 4.4 Advanced On the main menu, press the left and right direction buttons until the Advanced interface is displayed. -
Page 23: Advanced Menu
Figure 4-19 Advanced 4.4.2 Advanced Menu If you are not professional personnel, do not change parameters in the Advanced menu. You can select Advanced by the up and down buttons on the remote control. Figure 4-20 Enter passwords The default password is 8888. On the Advanced interface, technical personnel can configure parameters for ADC calibration, image mode, white balance, special settings, screens and more. -
Page 24: Software Update (Usb)
Figure 4-21 Advanced 4.4.3 Software Update (USB) Press the up and down direction buttons on the remote control to select Software Update (USB), and the system will search USB storage device. The software update files must be stored at the first level directory; otherwise, the files cannot be identified. -
Page 25: Osd Language
Figure 4-22 System 4.5.1 OSD Language You can set on screen display language. Step 1 Select System > OSD Language. Figure 4-23 OSD language Step 2 Select the OSD language by the left and right buttons. OSD language includes English and Chinese. Step 3 Press Menu on the remote control to complete the setting. -
Page 26: Osd Blending
Figure 4-24 OSD duration Step 2 Set OSD duration by the left and right buttons on the remote control according to your requirement. There are four choices for the OSD duration: OFF, 30s, 60s, and 180s. If you select OFF, the menu will not disappear automatically. ... -
Page 27: Soft Address Switch
Figure 4-26 Backlight mode Step 2 Adjust backlight mode by the left and right buttons on the remote control according to your requirement. There are three backlight modes: Highlight, Normal, and Eco. 4.5.5 Soft Address Switch Soft address switch is used to set soft address switch. Step 1 Select System >... -
Page 28: Input Source
Figure 4-28 Restore to factory settings Step 2 Select whether to restore to factory settings by the left and right buttons on the remote control according to your requirement. Step 3 Press Menu on the remote control to complete the setting. 4.6 Input Source You can select input signal source types for video walls. - Page 29 Figure 4-30 Multimedia (1) Select photo, music, movies, and texts by the left and right buttons on the remote control, and then press Enter, the interface of items you selected is displayed. Figure 4-31 Multimedia (2) You can also change settings for the pictures, music, movies, and files that are to be played.
-
Page 30: Faq
Most problems can be solved by the following solutionss. If problems that you encountered do not belong to the following descriptions, contact after sales personnel. Problems Solutions Check whether the power source (220V AC) is connected to alternating current. When you turn on the LCD video Check whether the power cable is broken. -
Page 31: Appendix 1 Cybersecurity Recommendations
Appendix 1 Cybersecurity Recommendations Cybersecurity is more than just a buzzword: it’s something that pertains to every device that is connected to the internet. IP video surveillance is not immune to cyber risks, but taking basic steps toward protecting and strengthening networks and networked appliances will make them less susceptible to attacks. - Page 32 Enable HTTPS We suggest you to enable HTTPS, so that you visit Web service through a secure communication channel. MAC Address Binding We recommend you to bind the IP and MAC address of the gateway to the device, thus reducing the risk of ARP spoofing.
Need help?
Do you have a question about the LS460UCM-EF and is the answer not in the manual?
Questions and answers