Dahua VTH5221DW-C User Manual
  1. Manuals
  2. Brands
  3. Dahua Manuals
  4. Monitor
  5. VTH5221DW-C
  6. User manual

Dahua VTH5221DW-C User Manual

7-inch digital vth
Hide thumbs Also See for VTH5221DW-C:
Table of Contents

Advertisement

Quick Links

7-inch Digital VTH User's Manual
V1.0.0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VTH5221DW-C and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Dahua VTH5221DW-C

Summary of Contents for Dahua VTH5221DW-C

  • Page 1 7-inch Digital VTH User’s Manual V1.0.0...

  • Page 2: Table Of Contents

    Table of Contents General Introduction ....................5 1.1 Product Intro ......................5 1.2 Applicable Model ....................... 5 Structure and Appearance ..................6 2.1 Front Panel ....................... 6 2.2 Rear Panel ........................ 7 Networking ........................ 9 Installation and Debug .................... 10 4.1 Device Wiring ......................
  • Page 3 5.5 Monitor ........................30 5.5.1 Door ........................30 5.5.2 IPC ........................32 5.5.3 Favorite ........................ 35 5.6 Arm/Disarm ......................35 5.7 Info.......................... 37 5.8 Default ........................38 Appendix 1 Technical Specification ................39...
  • Page 4 Important Safeguards and Warnings Please read the following safeguards and warnings carefully before using the product in order to avoid damages and losses. Note: Do not expose the device to lampblack, steam or dust. Otherwise it may cause fire or ...

  • Page 5: General Introduction

    This user’s manual is applicable to many models of product, please refer to Chart 1-1. Model Color Front Screen SD Card Camera VTH5221DW Silver+White Not support Capacitive Support touch screen VTH5221D Gold+Black Not support Capacitive Support touch screen VTH5221DW-C Silver+White Support Capacitive Support touch screen VTH5221D-C Gold+Black Support Capacitive Support touch screen Chart 1-1...

  • Page 6: Structure And Appearance

    2 Structure and Appearance 2.1 Front Panel Note: Only VTH5221D(W)-C has front camera and other models do not support front camera. Front panel is in Figure 2-1. Components are defined in Chart 2-1. Figure 2-1 Component Description Name Camera Cover Slide, you can cover or open camera.

  • Page 7: Rear Panel

    Component Description Name Emergency In emergency, press this button to call MGT center. Chart 2-1 2.2 Rear Panel Different models have different real panels, but all of interfaces are the same. Real panel is in Figure 2-2. Components are in Figure 2-2 Name Description...
  • Page 8 Name Description Interface Chart 2-2...

  • Page 9: Networking

    3 Networking VTH networking is in Figure 3-1. Figure 3-1...

  • Page 10: Installation And Debug

    4 Installation and Debug 4.1 Device Wiring Device wiring is in Figure 4-1. Figure 4-1 4.2 Device Installation Warning:  Avoid installation in poor environment, such as condensation, high temperature, oil stain, dust, corrosion or direct sunlight.  Project installation and debugging must be done by professionals. Please do not open the...

  • Page 11: Screw

    device in case of failure, and please contact after sales service. 4.2.1 Screw Component Name Diagram Quantity M4×30 cross pan head machine screw Chart 4-1 4.2.2 Steps See Figure 4-2. Figure 4-2 Step 1. Embed 86 box into wall. Step 2. Fix installation bracket on 86 box with two M4×30 cross pan head machine screws. Step 3.

  • Page 12: Device Debug

    4.3 Device Debug 4.3.1 Before Debugging Debugging personnel shall be familiar with related materials, know device installation, wiring and usage. Debugging personnel check whether circuit has short circuit or open circuit or not. Make sure circuit is normal, plug device to power. After debugging end, clear up site (handle plugs, fix device and etc.) 4.3.2 Debug Device Step 1.
  • Page 13 Now device interface shows at the upper-right corner which means wireless connection is successful.  Wired: Select Wired. See Figure 4-4. Figure 4-4 Enter VTH Local IP, Subnet Mask and Gateway. Press OK. Now device interface shows at the upper right corner which means wired connection is successful.
  • Page 14 Figure 4-5  If you want to set this VTH to be extension VTH, then you shall select Extension. Fill in user cinfig info for extension to auto sync with master, such as room no. and master IP. See Figure 4-6. Figure 4-6 Press OK to save config.

  • Page 15: Successfully Debug

    Warning: Before config, please make sure VTO is plugged to power and is in the same segment with VTH. Fill in VTO name, master VTO IP address, set enable status to , see Figure 4-7. Figure 4-7 Fill in VTO name, and extension VTO IP address, select device type, set enable status to The device supports n19 units of extensions, and you can press to page down to add more extensions.
  • Page 16 Figure 4-8 Icon Icon Name Note config electric control lock, press Unlock 1 , unlock. If this VTO has 485 expansion interface, it can expand electric control lock or door sensor Unlock 2 lock, after successfully matching with VTH, press , unlock.
  • Page 17 Icon Icon Name Note Volume Adjust call volume. 、 Accept Call Hang up...

  • Page 18: Product Function

    5 Product Function 5.1 Homepage Main menu includes Call, Info, Monitor, SOS, Setting and Arm/Disarm. See Figure 5-1. Figure 5-1 Name Description Room No. VTH position Call You can view all call records here, including missed call and outgoing call. You can create contacts. Info You can view, delete and clear announcement and alarm info released by MGT center, and message and etc.

  • Page 19: Setting

    ：Unread message. Time Show date, week, time, zone and zone alarm. Arm/Disarm Press this icon to enter arm/disarm. Setting Shortly press Setting button, enter setting interface. Long press Setting button for 6 seconds, enter protect setup interface. Press to call MGT center. Monitor Monitor VTO, IPC video.

  • Page 20: Dnd

    5.2.1.4 Other Go to Setting>Ring>Other, see Figure 5-2. Set VTO ring time, VTH ring time, and etc. Figure 5-2 Note:  Ring as VTO calls VTH has maximum of 120 seconds, and message video time is 0-90 seconds. Please refer to Ch 5.2.5.4. If message time is 0 seconds, you cannot leave message.
  • Page 21 Step 2. Press to enable DND hour. Step 3. Set DND hours. See Figure 5-3. Figure 5-3 5.2.2.2 DND Period Step 1. GO to Setting>DND. Step 2. Set period. Step 3. Set week. See Figure 5-4.

  • Page 22: Alarm

    Figure 5-4 5.2.3 Alarm VTH supports 6-ch alarm zone setup. Go to Setting>Alarm>Zone, set each zone’s alarm switch, alarm status, alarm time and etc. Step 1. Go to Setting>Alarm. See Figure 5-5. Figure 5-5 Step 2. In Zone interface, follow Chart 5-1 to select zone type, NO/NC, alarm status and delay time.

  • Page 23: Mode

    Parameter Note Zone Set detector zone no. Type According to each zone detector type, select zone type, including IR, gas, smoke sensor and etc. NO/NC Set detector NO or NC. Alarm Instant alarm：once prompt tone stops, it enters arming. Status Delay alarm：it enters arming when delay time ends.

  • Page 24: General

    5.2.5 General Go to Setting>General, set VTH time, password, display and etc. 5.2.5.1 Time Go to Setting>General>Time, set VTH time. Step 1. Select Setting>General>Time. Step 2. Press enable system time. Now device system time and VTO time are synced. You also may modify system time and set time zone, this time will not be synced with VTO. See Figure 5-7.
  • Page 25 Note:  Initial password to enter setting interface, and personal unlock password and arm/disarm password are all: 123456.  Duress password is the inverse of arm/.disarm password, for example if arm/disarm password is 123456, then duress password is 654321.  Personal unlock password is used to unlock VTO, as you enter “#+4-digit room no.+ personal unlock password+#”.

  • Page 26: Production

    5.2.6 Production Go to Setting>Production, see Figure 5-9. Press reboot System or SD Format to reboot system or format SD card, respectively. Figure 5-9 5.3 Call Note:  Call function is used in VTH calling VTH.  If two residential VTH both have cameras, then a bidirectional video talk can be performed.
  • Page 27 Figure 5-10 Step 2. Enter room no. you want to call, press icon to call. After call is accepted, you can perform a bidirectional talk. See Figure 5-11. Tips: If you want to call extension of the VTH , such as 9901-1, just enter “-1” to call it. Figure 5-11...

  • Page 28: Contact

    5.3.1.2 Call via Contact Warning: You must add contact first before you can call designated resident via contact. Please refer to Ch 5.3.2. Step 1. Select Call>Contact. Step 2. Select resident you want to call, press to call. 5.3.2 Contact Go to Call>Contact interface, you can add, delete, modify call contact.

  • Page 29: Recent Call

    Figure 5-13 Step 4. Press OK to add contact. If you want to delete contact, press and check resident you want to delete, press Delete to delete. If you want to edit contact, select contact, press to modify contact. If you want to call contact, select contact you want to call and press 5.3.3 Recent Call In Call>Recent Call interface, you can view, delete call records if the VTH, see Figure 5-14.

  • Page 30: Sos Call

    Figure 5-14 If you want to call missed call back, just select contact, and press to call. If you want to delete call record, press and select record you want to delete, press Delete. You also can press and in pop-up box, press OK if you want to delete all records.
  • Page 31 Figure 5-15 Step 2. Select door you want to monitor, press . See Figure 5-16. Figure 5-16 Step 3. Please refer to Chart 5-2. Icon Icon Name Note Return Snapshot Press to snapshot.

  • Page 32: Ipc

    Icon Icon Name Note Press to record. Record Save record to SD card, and overwrite if full. with electric control lock, press Unlock 1 to unlock. If the VTO has 485 expansion interface, it can expand electric control lock or door sensor Unlock 2 lock, after successfully matching with VTH, press...
  • Page 33 Figure 5-17 Step 3. Please refer to Chart 5-3. Parameter Note Name Camera name. IPC’s IP Username Username and password to login IPC WEB Password Port Port no. of IPC Stream According to stream type you want to select, when network bandwidth is insufficient, sub stream is recommended.
  • Page 34 Figure 5-18 If you want to delete IPC, press Edit, and select IPC you want to delete, press Delete. 5.5.2.2 Monitor IPC Step 1. Select Monitor>IPC. Step 2. Select IPC to monitor. Step 3. Press . See Figure 5-19. Figure 5-19...

  • Page 35: Favorite

    Step 4. Please refer to Chart 5-3 and complete operation. 5.5.3 Favorite If one VTH monitors more than one VTO or IPC at the same time, you can go to Door or IPC interface, select the VTO or IPC you monitor the most frequently, and press to add them into Favorite.
  • Page 36 Figure 5-21 Step 2. Select one mode from Stay, Away, Sleep and Custom. Step 3. In pop-up arm interface, enter arm password. Device generates tone, which means successfully armed. Note: Initial arm password is 123456. Disarm Step 1. In homepage, press designated mode to disarm. Step 2.

  • Page 37: Info

    5.7 Info In home page press , you can view, delete and clear announcement and alarm info released by MGT center, plug guest message and etc. Here used guest message as an example. Step 1. Go to Info>Guest Message. See Figure 5-22. Figure 5-22 Step 2.

  • Page 38: Default

    Figure 5-23 Step 3. Please refer to Chart 5-4. Icon Icon Name Note Retune Switch Switch to previous/next message. 、 Pause Stop Quick Play Quickly play guest message. Slow Play Slowly play quest message. Volume Adjust volume of message. 、 Chart 5-4 5.8 Default If you want to restore all settings in project, you can follow these steps:...

  • Page 39: Appendix 1 Technical Specification

    Appendix 1 Technical Specification Model VTH5221D Main Processor Embedded CPU System Embedded Linux OS 7 inch HD LCD Display 1024×600 Video Camera(—C model) 1.0 MP CMOS HD camera Talk Bidirectional audio talk Audio Input Omnidirectional MIC Audio Enhancement HLC and NR Input capacitive touch button and 5 shortcut key Operation...

This manual is also suitable for:

Vth5221dwVth5221dVth5221d-c

Table of Contents