1.1 Safety Precautions TOP PREVIOUS NEXT 1. Before servicing, unplug the power cord to prevent electrical shock hazard. 2. When replacing parts, user only manufactures recommended components for safety. 3. Check the condition of power cord. Replace if wear or damage is evident. 4.
1.2 Electrical Tests TOP PREVIOUS NEXT 1. Unplug the power cord and check for continuity between the earth ground connection on the plug and the Interface Board Cover. There should be zero ohm resistance 2. With the unit unplugged, short the AC live-neutral of the plug with a jumper wire. 3.
1.3 For Service Technicians TOP PREVIOUS NEXT ICs and LSIs are vulnerable to static electricity. When repairing, the following precautions will help to prevent recurring malfunctions. 1. Cover the plastic parts with aluminum foil. 2. Ground the soldering irons. 3. Use a conductive mat on the worktable. 4.
2 SPECIFICATION TOP PREVIOUS NEXT Item Model No. KV-S2065L KV-S2065W Scanner Scanning face Duplex scanning Scanning method Front side: CIS (Contact Type Image Sensor) Back side: CIS (Contact Type Image Sensor) Scanning speed Simplex scanning: Approx. 60 ppm (Letter, fed lengthwise, 200 dpi) Duplex scanning: Approx.
Page 7
Option Roller exchange kit (KV-SS009), Imprinter option (KV-SS010), Roller cleaning paper (KV-SS03), Ink cartridge (KV-SS06), White roller kit for KV-S2065W (KV-SS048), White roller kit for KV-S2065L (KV-SS071) Weight in pounds represents the weight of 500 [17x22 inches (432x559mm)] sheets. TOP PREVIOUS NEXT...
Page 8
3 COMPONENT IDENTIFICATION TOP PREVIOUS NEXT...
4 INSTALLATION TOP PREVIOUS NEXT 4.1 Minimum Space Requirements 4.2 Removing and Keeping Screw and Fixture 4.3 DIMM Module Extension 4.4 Removing SCSI Board 4.5 Installing DIMM Module 4.6 Installing the SCSI Board 4.7 Connecting the Unit to a Personal Computer 4.8 System Conditions Requirements 4.9 LCD Settings 4.9.1 Setting the language...
4.3 DIMM Module Extension TOP PREVIOUS NEXT A maximum of 256 MB extended memory may be required depending on the combination of the paper size, resolution and gray scale mode. To determine how much extended memory is required, refer to the following page Additional Memory Size each scanning mode (MB).
4.5 Installing DIMM Module TOP PREVIOUS NEXT Insert the DIMM module into the connector on the SCSI interface board at an angle [ Place ( 1 ) ]. Push in the module as far as it goes. The levers should lock automatically. If not, push the levers tolock the module in [Place ( 2 ) ].
4.6 Installing the SCSI Board TOP PREVIOUS NEXT 1) Insert the SCSI Board into the unit along the rails and push it in firmly. Confirm that the SCSI board plate is fully inserted until it firmly locks in place. 2) Secure the SCSI Board with the 2 screws. 3) Install the scanner driver software in your computer according to the enclosed manuals.
Page 18
4.7 Connecting the Unit to a Personal Computer TOP PREVIOUS NEXT Note: * AC cord shown on the figure is for AC100-120V. Caution : Set the power switch on the scanner and on the personal computer to OFF before connecting the interface cable. Use only the power cord that is supplied by the manufacturer.
4.8 System Conditions Requirements TOP PREVIOUS NEXT When using the scanner, the required personal computer conditions are as follows. Pentium 166MHz or higher (Pentium, Celeron processor or higher is recommended. Memory 64 MB or higher (128 MB or higher is recommended.) Windows 95/Windows 98/Windows NT/Windows2000/Windows Me SCSI board Adaptec Brand AHA-1540/2930/2940/19160/29160 Series are recommended.
4.9 LCD Settings TOP PREVIOUS NEXT Before scanning the document, perform the required settings on the display. Setting information and scanner conditions are shown on the display. 4.9.1 Setting the language 4.9.2 Setting the SCSI ID and Terminator TOP PREVIOUS NEXT...
4.9.1 Setting the language TOP PREVIOUS NEXT 1. Turn the power on while pressing the HOME key. Note: The language setting mode is selected automatically when the units power is turned on for the first time after the unit was purchased. 1.
4.9.2 Setting the SCSI ID and Terminator TOP PREVIOUS NEXT 1. Press the OTHERS Key. Enters setting modes other than SCAN, COUNTER, or IMPRINT and displays the version 1. Press the MODE Key. Press the MODE Key [ ] to display the SCSI ID, which is the fourth setting. 1.
Page 23
To active the SCSI ID settings, press the HOME Key to return to READY, then turn the unit off and on. 1. Press the SELECT [ ] Key or [ ] Key to select the desired setting. The [ ] Key moves to the next content as shown below. The [ ] Key moves to the previous content.
6 MECHANICAL FUNCTION TOP PREVIOUS NEXT 6.1 Paper Feed Mechanism 6.2 Manual Feed Mechanism and ADF Adjustment TOP PREVIOUS NEXT...
Page 34
6.1 Paper Feed Mechanism TOP PREVIOUS NEXT 1. When PC outputs the scanning-start command, the Hopper lifts until the paper contacts the Paper Feed Roller. 2. The Conveyor Motor is transferred to the rotation of the Conveyor Rollers, Drive Rollers and Exit Roller. 3.
Page 35
Start-position,activating the Starting Position Sensor, CIS starts to scan the data on the page. And the Back-side Scanning Start process is same as Front-side Scanning. 6. When the Waiting Sensor detects the end of the first page, the Paper Feed Motor starts to rotate again. As a result, the second page is passed into the paper feed route.
Page 36
6.2 Manual Feed Mechanism and ADF Adjustment TOP PREVIOUS NEXT 1. By setting the ADF/manual feed Selector to the Manual position you can separate the Retard Roller from the Separation Roller and scan one sheet or several sheets. 2. By setting the ADF/manual feed Selector to the ADF ADJ. position, the contact force between the Retard Roller and the Separation Roller goes up, according to the increment of the ADF ADJ.
Drive Roller 3 PBDRX01S2065 C Conveyor Roller 1 -3 PBDRX02S2065 C Straight Exit Roller PBDRX02S2065 C Exit Roller PBDRX03S2065 C Sensor Roller 1 for KV-S2065L PBDRA0013Y-J for KV-S2065W PBDRA0102X-J Sensor Roller 2 for KV-S2065L PBDRA0112Y-J for KV-S2065W PBDRA0102X-J for KV-S2065L EQ4R219Q1...
Page 40
This product KV-SS009 is supplied via sales route. TOP PREVIOUS NEXT...
7.2 Roller Cleaning TOP PREVIOUS NEXT 7.2.1 Paper Feed Roller, Separation Roller, Retard Roller 7.2.2 Drive Roller and Conveyor Rollers TOP PREVIOUS NEXT...
Page 42
7.2.1 Paper Feed Roller, Separation Roller, Retard Roller TOP PREVIOUS NEXT 1. Turn off the Power. 2. Open the Front door. 3. Clean the surfaces of the Paper Feed Roller and Separation Roller and Separation Roller with cleaning paper (KV-SS03). 4.
Page 43
Note 1: Make sure to clean the Retard Roller from right to left. If the roller is cleaned from left to right, it may slip out of position. Note 2: After cleaning the above rollers, clear Clean Roller Warning on Other Setting Mode as shown in Section 9.
Page 44
7.2.2 Drive Roller and Conveyor Rollers TOP PREVIOUS NEXT 1. Turn off the Power. 2. Open the Front door. 3. Clean the Driver and Conveyor Rollers with cleaning paper (KV-SS03), as shown in Fig. 7-3 (same as cleaning the Plastic Free Roller).
Page 46
TOP PREVIOUS NEXT 1. Open the Front door. 2. Clean the CIS glass using the accessory roller cleaning paper (KV-SS03). Also, remove the dirt on the document sensors and double feed detection sensors with the blower Scanner (KV-S2065L/W) has. Note: When cleaning the bottom CIS glass, do not touch the tip of the plastic pointer (black) in the back of the unit.
7.4 Sensor Roller Cleaning TOP PREVIOUS NEXT 1. Open the Front door. 2. Clean the Sensor Roller with cleaning paper (KV-SS03), as shown in Fig. 7-3. Note: If the Sensor Roller is removed while cleaning, re-attach it after cleaning as follows. 7.4.1 Re-attachment of the Sensor Roller Assembly TOP PREVIOUS NEXT...
Page 49
7.4.1 Re-attachment of the Sensor Roller Assembly TOP PREVIOUS NEXT When the Sensor Roller is removed for cleaning the inside of the scanner, reattach it as shown below. Lower Sensor Roller: 1. Attach the roller by placing the gear side to the left side of the scanner and inserting both sides bearings into the guide grooves. Note: After attaching, press down on top of the Sensor Roller with your finger to confirm if it moves or not.
Page 51
7.5 Replacing Limited Life Parts TOP PREVIOUS NEXT If Warning Replace Roller message is displayed on the LCD, replace the Paper Feed Roller Module and Retard Roller Module at the same time. 1. Turn the power off and unplug the power cord. 2.
Page 52
4. Open the optional Roller Exchange Kit (KV-SS009), and take out the Paper Feed Roller Module. 5. Install the new Paper Feed Roller Module with the gear on the left side and the bearings into the guide grooves of the side chassis in the scanner [(1)].
Page 53
7. Pull and open the Conveyor(Lower) towards you by using the indent on the right side. Note: When the Conveyor is pulled towards you, the rocking mechanism will be release. When opening the Conveyor, be careful not to get your finger stuck in the indent.
Page 54
Note: When the conveyor is closed, the click-stop mechanism will operate. If the Conveyor is not closed correctly and operation in step 12 as is done, the Conveyor may break. 12. Close the Front Door. Note 1: Push both sides of the Front Door down slowly until it clicks into place. Note 2: After replacing rollers, clear Replace Roller Warning on Other Setting Mode as shown in Section 9.
Page 55
8 DISASSEMBLY INSTRUCTIONS TOP PREVIOUS NEXT 8.1 Disassembly Flowchart 8.2 Exterior 8.2.1 Rear Panel (with Post Imprinter Door) 8.2.2 Side Cover (R) 8.2.3 Switch Panel 8.2.4 Side Panel (R) 8.2.5 Exit Cover 8.2.6 Pre Imprinter Door 8.2.7 Side Panel (L) 8.2.8 Feed Unit Cover (L) 8.2.9 Feed Unit Cover 8.2.10 Hopper Unit...
Page 56
8.3.6 Paper Feed Roller 8.3.7 Exit Roller 8.3.8 Straight Exit Roller 8.3.9 Drive Belt 8.3.10 Conveyor Motor 8.3.11 Feed Motor 8.3.12 Turn Conveyor Plate (Inner) 8.3.13 Straight Exit Conveyor Plate 8.3.14 Board Box Cover 8.3.15 SCSI Board 8.3.16 Board Box Unit 8.3.17 Front Door Switch 8.3.18 Gas Spring 8.3.19 Pointer...
Page 57
8.4.7 DC-DC CONVERTER Board 8.4.8 ENDING (FRONT) POSITION SENSOR Board 8.4.9 RELAY (UPPER) Board 8.4.10 WAITING SENSOR Board 8.4.11 STARTING POSITION SENSOR Board 8.4.12 WAITING LED Board 8.4.13 STARTING POSITION LED Board 8.4.14 RELAY (LOWER) Board 8.4.15 PAPER JAM SENSOR Board 8.4.16 ENDING (FRONT) POSITION LED Board 8.4.17 SIZE DETECTOR Board and Paper Detector 8.4.18 HOPPER POSITION Board...
Page 58
8.1 Disassembly Flowchart TOP PREVIOUS NEXT When reassembling, perform the steps in the reverse order unless otherwise noted in Reassembling Notes.
Page 60
8.2 Exterior TOP PREVIOUS NEXT 8.2.1 Rear Panel (with Post Imprinter Door) 8.2.2 Side Cover (R) 8.2.3 Switch Panel 8.2.4 Side Panel (R) 8.2.5 Exit Cover 8.2.6 Pre Imprinter Door 8.2.7 Side Panel (L) 8.2.8 Feed Unit Cover (L) 8.2.9 Feed Unit Cover 8.2.10 Hopper Unit TOP PREVIOUS NEXT...
Page 61
8.2.1 Rear Panel (with Post Imprinter Door) TOP PREVIOUS NEXT 1. Remove 6 screws. 2. Remove cable from CN530 of POST IMPRINTER DOOR Board. TOP PREVIOUS NEXT...
8.2.2 Side Cover (R) TOP PREVIOUS NEXT 1. Remove 2 screws and the Side Cover (R). 2. Remove Side Cover (R) pushing down for arrow direction. TOP PREVIOUS NEXT...
8.2.3 Switch Panel TOP PREVIOUS NEXT 1. Remove 3 screws and the Switch Panel after opening Front Door. 2. Remove cable from CN551 of PANEL Board. TOP PREVIOUS NEXT...
Page 64
8.2.4 Side Panel (R) TOP PREVIOUS NEXT 1. Remove the Rear Panel. (See 8.2.1) 2. Remove the Side Cover (R). (See 8.2.2) 3. Remove the Switch Panel. (See 8.2.3) 4. Remove the Rear Panel. (See 8.2.1) 5. Remove 4 screws and the Side Panel (R). TOP PREVIOUS NEXT...
8.2.5 Exit Cover TOP PREVIOUS NEXT 1. Remove the Rear Panel. (See 8.2.1) 2. Remove 2 screws. TOP PREVIOUS NEXT...
Page 66
8.2.6 Pre Imprinter Door TOP PREVIOUS NEXT 1. Remove the Exit Cover. (See 8.2.5) 2. Push the Stacker as shown in the Fig. 8-7. TOP PREVIOUS NEXT...
Page 67
8.2.7 Side Panel (L) TOP PREVIOUS NEXT 1. Open Front Door. 2. Remove 2 screws and the Side Panel (L). /(Pull out while pushing down the 3 locking sections from the chassis) TOP PREVIOUS NEXT...
Page 68
8.2.8 Feed Unit Cover (L) TOP PREVIOUS NEXT 1. Remove 2 screws after removing Pre Imprinter Door. 2. Remove the Feed Unit Cover (L). /(Pull out while pushing down the locking section) TOP PREVIOUS NEXT...
Page 69
8.2.9 Feed Unit Cover TOP PREVIOUS NEXT 1. Remove the Feed Unit Cover (L). (See 8.2.8) 2. Loosen 4 screws and the Feed Unit Cover. TOP PREVIOUS NEXT...
8.2.10 Hopper Unit TOP PREVIOUS NEXT 1. Remove the Switch Panel and the Side /Panel (L). (See 8.2.3 and 8.2.7) 2. Remove 4 screws (A). 3. Remove 2 screws (B). 4. Disconnect connector CN512. Note: When assembling, cable connected to CN512 should be inserted, while white base side of the cable (without character) is located to the upper.
Page 73
8.3.1 CIS (Contact type Image Sensor) /Front/ TOP PREVIOUS NEXT 1. Remove Feed Unit Cover (L). (See 8.2.8) 2. Slide the Sensor Roller 2 to the right and remove the Sensor Roller. 3. Remove 2 screws and remove the Conveyor Plate Upper 2. 4.
Page 74
8.3.2 CIS (Contact type Image Sensor) /Back TOP PREVIOUS NEXT 1. Remove Sensor Roller 1. 2. Remove screw and Conveyor Plate Lower 2. 3. Remove Drive Roller 3. 4. Remove 4 hexagonal bolts. 5. Disconnect all connectors. 6. Remove the CIS Back. 7.
Page 75
8.3.3 Conveyor Roller (1) - (3) TOP PREVIOUS NEXT 1. Remove the Side Panel (L). (See 8.2.7) 2. Open the Front Door. 3. Remove 4 screws and Turn Conveyor Plate(outer). 4. Remove E-Rings from both sides of roller, and /remove bearing and gear. TOP PREVIOUS NEXT...
Page 76
8.3.4 Driver Roller (1) - (3) TOP PREVIOUS NEXT 1. Open the Front Door. 2. Remove Conveyor Plate Lower 2. (See 8.3.2-(2)) 3. Unlock the rollers from the notching hole of chassis and remove them. 4. Remove E-Rings from both sides of roller, and remove bearing and gear. TOP PREVIOUS NEXT...
8.3.5 Retard Roller TOP PREVIOUS NEXT 1. Open the Front Door and remove Lower Conveyor Plate 1. 2. Remove the Retard Roller, as shown in Fig. 8-16. TOP PREVIOUS NEXT...
8.3.6 Paper Feed Roller TOP PREVIOUS NEXT 1. Open the Front Door. 2. Pull the Feeder Roller Block from Magnet. 3. Pull the lock levers for the Paper Feeder Roller Module, as shown in Fig. 8-17. TOP PREVIOUS NEXT...
8.3.7 Exit Roller TOP PREVIOUS NEXT 1. Remove Exit Cover. (See 8.2.5) 2. Remove Feed Unit Cover (L). (See 8.2.8) 3. Remove Exit Roller. 4. Remove E-Rings from both sides of roller, and remove bearing and gear. TOP PREVIOUS NEXT...
Page 80
8.3.8 Straight Exit Roller TOP PREVIOUS NEXT 1. Remove the Rear Panel and the Straight Exit Roller. 2. Remove E-Rings from both sides of roller, and remove bearing and gear. TOP PREVIOUS NEXT...
Page 81
8.3.9 Drive Belt TOP PREVIOUS NEXT 1. Remove Side Panel(L). (See 8.2.7) 2. Loosen 2 screws and release the Tension Pulley. 3. Remove the Drive Belt. Note: When the Belt is installed, the tension spring will automatically apply tension to the belt. (RE-ASSEMBLE NOTE)
Page 83
8.3.10 Conveyor Motor TOP PREVIOUS NEXT 1. Remove Drive Roller-2. (See 8.3.4-(1), (2), (3)) 2. Loosen 2 screws and release the tension pulley. 3. Remove the 2 screws. 4. Remove the Conveyor Motor with Motor Mount. 5. Disconnect the connector from the Conveyor Motor. TOP PREVIOUS NEXT...
8.3.11 Feed Motor TOP PREVIOUS NEXT 1. Remove Drive Roller-1. (See 8.3.4-(1), (2), (3)) 2. Remove the screw (A) from the Retard Transmission Shaft Holder. Note: When reattach a rink spacer to the scanner, be careful with the direction of the spacer. 1.
Page 85
8.3.12 Turn Conveyor Plate (Inner) TOP PREVIOUS NEXT 1. Remove the Pre Imprinter Door. (See 8.2.6) 2. Remove 4 screws. 1. Remove the 4 claws. 2. Disconnect CN526. TOP PREVIOUS NEXT...
Page 86
8.3.13 Straight Exit Conveyor Plate TOP PREVIOUS NEXT 1. Remove Rear Panel. (See 8.2.1) 2. Remove Straight Exit Roller. (See 8.3.8) 3. Remove 3 screws. 4. Remove the Straight Exit Conveyor Plate. TOP PREVIOUS NEXT...
Page 87
8.3.14 Board Box Cover TOP PREVIOUS NEXT 1. Remove Side Cover (R). (See 8.2.2) 2. Remove 5 screws and the Board Box Cover. TOP PREVIOUS NEXT...
8.3.15 SCSI Board TOP PREVIOUS NEXT 1. Remove 2 screws and the Interface Board Cover. 2. Pull out SCSI Board, holding the handle. TOP PREVIOUS NEXT...
Page 89
8.3.16 Board Box Unit TOP PREVIOUS NEXT 1. Remove Rear Panel, Side Cover (R), Switch Panel, and Side Panel (R). (See 8.2.1 to 8.2.4) 2. Remove 8 screws and wire harness. 1. Remove 2 screws (Back View). 2. Remove the Board Box Unit. TOP PREVIOUS NEXT...
Page 90
8.3.17 Front Door Switch TOP PREVIOUS NEXT 1. Remove Board Box Unit. (See 8.3.16) 2. Remove 2 screws. 3. Disconnect 2 lead wires. 4. Remove the front Door Switch. TOP PREVIOUS NEXT...
8.3.18 Gas Spring TOP PREVIOUS NEXT 1. Remove Board Box Unit. (See 8.3.16) 2. Remove the screw(a). 3. Remove the screw(b). 4. Remove the Gas Spring. TOP PREVIOUS NEXT...
Page 92
8.3.19 Pointer TOP PREVIOUS NEXT 1. Remove Board Box Unit. (See 8.3.16) 2. Remove the right side E-Ring. 3. Remove the left side Paper Path Selector and E-Ring. 4. Remove the Pointer. TOP PREVIOUS NEXT...
8.4 Circuit Board Assemblies TOP PREVIOUS NEXT 8.4.1 MAIN CONTROL Board 8.4.2 POWER Board 8.4.3 MOTHER Board 8.4.4 DRIVE Board 8.4.5 POST IMPRINTER DOOR Board 8.4.6 PANEL Board 8.4.7 DC-DC CONVERTER Board 8.4.8 ENDING (FRONT) POSITION SENSOR Board 8.4.9 RELAY (UPPER) Board 8.4.10 WAITING SENSOR Board 8.4.11 STARTING POSITION SENSOR Board 8.4.12 WAITING LED Board...
Page 94
8.4.19 PAPER JAM LED Board 8.4.20 ENDING (REAR) POSITION SENSOR Board 8.4.21 POINTER DETECTOR Board 8.4.22 Power Switch 8.4.23 Fan TOP PREVIOUS NEXT...
8.4.1 MAIN CONTROL Board TOP PREVIOUS NEXT 1. Remove Side Cover (R) and Board Box Cover. (See 8.2.2 and 8.3.14) 2. Remove INTERFACE Board. (See 8.3.15) 3. Disconnect all connectors from/to MAIN CONTROL Board and MOTHER Board. Note: See Section 11 BLOCK DIAGRAM for connections. Before disconnecting all connectors, unlock the claws (Locking Section) on left side of clamps to release the cables from clamps.
8.4.2 POWER Board TOP PREVIOUS NEXT 1. Remove Board Box Unit. (See 8.3.16) 2. Remove 2 screws and separate the Power box from the Board Box Unit. 3. Disconnect all connect tors from/to POWER Board. Note: See SECTION 11 BLOCK DIAGRAM for connections 1.
Page 98
8.4.3 MOTHER Board TOP PREVIOUS NEXT 1. Remove Board box Unit. (See 8.3.16) 2. Remove SCSI Board, MAIN CONTROL Board. (See 8.3.15 and 8.4.1) 3. Disconnect 2 connectors from MOTHER Board. 4. Remove 4 screws and the MOTHER Board. TOP PREVIOUS NEXT...
8.4.5 POST IMPRINTER DOOR Board TOP PREVIOUS NEXT 1. Remove Rear Panel. (See 8.2.1) 2. Disconnect CN530. 3. Remove the screw inside the Rear Panel. TOP PREVIOUS NEXT...
8.4.7 DC-DC CONVERTER Board TOP PREVIOUS NEXT 1. Remove Side Cover (R), and Switch Panel. (See 8.2.1 and 8.2.3) 2. Remove 4 screws. 3. Disconnect CN861 and CN862. TOP PREVIOUS NEXT...
Page 104
8.4.8 ENDING (FRONT) POSITION SENSOR Board TOP PREVIOUS NEXT 1. Remove Exit Cover. (See 8.2.5) 2. Disconnect CN529. 3. Remove 2 screws. TOP PREVIOUS NEXT...
8.4.9 RELAY (UPPER) Board TOP PREVIOUS NEXT 1. Remove Exit Cover and Pre Imprinter Door./(See 8.2.5 and 8.2.6) 2. Remove 3 screws (A). 3. Remove 2 screws (B). 4. Disconnect all connectors. TOP PREVIOUS NEXT...
8.4.10 WAITING SENSOR Board TOP PREVIOUS NEXT 1. Remove the Conveyor Plate Upper 2. (See 8.3.1(1)-(3)) 2. Remove 2 screws. 3. Disconnect CN525. TOP PREVIOUS NEXT...
Page 107
8.4.11 STARTING POSITION SENSOR Board TOP PREVIOUS NEXT 1. Remove the Conveyor Plate Upper 2. (See 8.3.1(1)-(3)) 2. Remove 2 screws. 3. Disconnect CN524 and CN523. TOP PREVIOUS NEXT...
8.4.12 WAITING LED Board TOP PREVIOUS NEXT 1. Remove Drive Roller 1. (See 8.3.4) 2. Remove 2 screws. 3. Disconnect CN522. TOP PREVIOUS NEXT...
Page 109
8.4.13 STARTING POSITION LED Board TOP PREVIOUS NEXT 1. Remove Drive Roller 2. 2. Remove 2 screws. 3. Disconnect CN519 and CN520. TOP PREVIOUS NEXT...
8.4.14 RELAY (LOWER) Board TOP PREVIOUS NEXT 1. Remove Drive Roller 2. (See 8.3.4) 2. Disconnect all connectors. 3. Remove 2 screws. TOP PREVIOUS NEXT...
8.4.15 PAPER JAM SENSOR Board TOP PREVIOUS NEXT 1. Remove Turn Conveyor Plate. (See 8.3.12) 2. Remove the PAPER JAM SENSOR Board. 3. Disconnect CN526 and CN527 inside Turn Conveyor Plate. TOP PREVIOUS NEXT...
Page 112
8.4.16 ENDING (FRONT) POSITION LED Board TOP PREVIOUS NEXT 1. Remove Turn Conveyor Plate. (See 8.3.12) 2. Remove the ENDING (FRONT) POSITION LED Board. 3. Disconnect CN528. TOP PREVIOUS NEXT...
Page 113
8.4.17 SIZE DETECTOR Board and Paper Detector TOP PREVIOUS NEXT 1. Remove Hopper Unit. (See 8.2.10) 2. Remove 2 screws (a). 3. Disconnect CN513 and remove SIZE DETECTOR Board. 4. Remove 3 screws (b). 5. Disconnect connector and remove Paper Detector. TOP PREVIOUS NEXT...
8.4.18 HOPPER POSITION Board TOP PREVIOUS NEXT 1. Remove Lower Cover Plate 1. (See 8.3.5-(1)) 2. Remove Conveyor Plate Lower 2. (See 8.3.2-(2)) 3. Remove Hopper Unit. (See 8.2.10) 4. Push 3 Clip and remove 1 screw as shown in the Fig. 8-49 and remove the HOPPER POSITION Board.
8.4.19 PAPER JAM LED Board TOP PREVIOUS NEXT 1. Remove Conveyor Roller. (See 8.3.3) 2. Remove 2 screws. 3. Disconnect CN518. TOP PREVIOUS NEXT...
Page 116
8.4.20 ENDING (REAR) POSITION SENSOR Board TOP PREVIOUS NEXT 1. Remove Conveyor Roller. (See 8.3.3) 2. Remove 2 screws. 3. Disconnect CN516 and CN517. TOP PREVIOUS NEXT...
Page 117
8.4.21 POINTER DETECTOR Board TOP PREVIOUS NEXT 1. Remove Conveyor Roller. (See 8.3.3) 2. Remove 2 screws. 3. Disconnect CN514 and CN515. TOP PREVIOUS NEXT...
8.4.22 Power Switch TOP PREVIOUS NEXT 1. Remove the Power Box. (See 8.4.2-(1), (2)) 2. Disconnect the 2 lead terminals from the Power Switch terminal. 3. Remove the Power Switch from the chassis. (Pull out while pressing both sides of the locking section) WARNING (in case Power Switch and/or lnlet are replaced)
Page 119
8.4.23 Fan TOP PREVIOUS NEXT 1. Remove the Power Box. (See 8.4.2-(1), (2)) 2. Disconnect Fan connector. 3. Remove 2 screws and the Fan. TOP PREVIOUS NEXT...
9.1 Front Panel Specifications TOP PREVIOUS NEXT Item Contents Indication Device LCD Display Indication Matrix 16 Characters x 2 lines Kind of Character for Indication Alphabet, Number, Square Phonetic, Japanese Syllabary Indicated Contents System Status ( Initializing, Ready, Scanning, Error, Warning ) Setting ( Scanning, Counter, Imprinter, Other ) Service Mode Indicated Languages...
Page 123
1. Turn the power on while pressing the HOME Key. 1. Use the Key or the Key to select English Letter, English A4 or Deutsch A4, 1. Press the HOME Key. • The display will change to the select language, then the scanner will be ready. •...
9.2 Operation - 1 ( Normal Mode ) TOP PREVIOUS NEXT By pressing another key, you can enter the other Setting Mode directly, without returning back the READY Mode. The Imprinter Setting Mode will operate only if the Imprinter ( optional ) has been installed in the Main Unit (KV-S2065).
9.3 Operation - 2 (Service Mode) TOP PREVIOUS NEXT To enter Service Mode, turn on the Scanner while pressing the SCAN and the OTHER Keys simultaneously. Service Mode includes the Service Setting Mode and Test Mode. The Service Setting Mode offers functions that are not available in Normal Mode.The Service Setting Mode has Set Warning value for timing of cleaning or replacing roller, and so on.
9.4 Setting List TOP PREVIOUS NEXT 9.4.1 Scan Setting Mode ( Normal Mode 1 ) 9.4.2 Counter Setting Mode ( Normal Mode 2 ) 9.4.3 Imprinter Setting Mode ( Normal Mode 3 ) 9.4.4 Other Setting Mode ( Normal Mode 4 ) 9.4.5 Service Setting Mode ( Service Mode 1 ) 9.4.6 Test Mode ( Service Mode 2 ) TOP PREVIOUS NEXT...
Page 127
9.4.1 Scan Setting Mode ( Normal Mode TOP PREVIOUS NEXT TOP PREVIOUS NEXT...
Page 135
9.4.5 Service Setting Mode ( Service Mode 1 ) TOP PREVIOUS NEXT Note *1 : Setting content (A4 or Letter) on the item 4 depends on Set lan guage.
Page 138
9.4.6 Test Mode ( Service Mode 2 ) TOP PREVIOUS NEXT TOP PREVIOUS NEXT...
Page 139
Factory Item Setting Contents Default Setting 1-a Feed Test (Set Resolution and Test ) 100 - 600 START 1-b Feed Test (Set Size and Test) START 1-c Feed Test (Set Length Control and Test) LC OFF LC ON START 1-d Feed Test (Set Mode and Test) Mode 1 Mode 2 Mode 3...
9.5 Setting Operation ( Normal Mode ) TOP PREVIOUS NEXT 9.5.1 Scan Setting Mode ( Normal Mode 1 ) 9.5.2 Counter Setting Mode ( Normal Mode 2 ) 9.5.3 Imprinter Setting Mode ( Normal Mode 3 : Option ) 9.5.4 Other Setting Mode ( Normal Mode 4 ) TOP PREVIOUS NEXT...
Page 141
START POWER ON READY on LCD? Push SCAN key once Push COUNTER key once Push IMPRINT key once Push OTHERS key once Enters Enters Enters Enters Scan Counter Imprint Other Setting Setting Setting Setting Mode Mode Mode Mode (To Section 9.5.1) (To Section 9.5.2) (To Section 9.5.3) (To Section 9.5.4)
Page 142
9.5.1 Scan Setting Mode ( Normal Mode TOP PREVIOUS NEXT Mode - 1 Mode - 2 TOP PREVIOUS NEXT...
Page 143
(From Section 9.5) Item (From Section 9.5.1.2) F. Color drop F. Brightness F. Emphasis F. Contrast F. Halftone Select a menu of Setting Item by pushing B. Color drop “ ” or “ ” key. B. Brightness (8) B. Emphasis (9) B.
Page 144
(From Section 9.5) Item (18)-a (18)-a Save Setting (Select memory) Push “ ” or “ ” key until Select a menu of Setting Item by 18. Save Setting pushing “ ” or “ ” key. xxxx is indicated. (18)-b Save Setting xxxx;...
Page 145
9.5.2 Counter Setting Mode ( Normal Mode 2 ) TOP PREVIOUS NEXT TOP PREVIOUS NEXT...
Page 146
(From Section 9.5) Item (1) Disp. Counter (2) User Counter Set counter value Select a menu of Setting Item by Set increment value Clear user counter pushing “ ” or “ ” key. (2)- Clear User Counter? (1) Scan/User/System (2)- Set the parameter by pushing “...
Page 147
9.5.3 Imprinter Setting Mode ( Normal Mode 3 : Option ) TOP PREVIOUS NEXT TOP PREVIOUS NEXT...
Page 149
9.5.4 Other Setting Mode ( Normal Mode TOP PREVIOUS NEXT Mode - 1 Mode - 2 TOP PREVIOUS NEXT...
Page 150
(From Section 9.5) Item (1) Version (2) Buzzer (3) SCSI ID (1) Version indication Select a menu of Setting Item by M; MAIN Board (4) Terminator Version pushing “ ” or “ ” key. (5) Transfer Rate Firmware Version M1.00 F1.00 (8) Product ID F;...
Page 151
(From Section 9.5) Item (6) Clean Roller Dips. % Clear warning for (6)- ; Indicates % based on the value of Select a menu of Setting Item by "Clean Roller" “ Clean Roller ” in Service Mode Setting pushing “ ”...
9.6 Setting Operation ( Service Mode ) TOP PREVIOUS NEXT 9.6.1 Service Setting Mode ( Service Mode 1 ) 9.6.2 Test Mode ( Service Mode 2 ) TOP PREVIOUS NEXT...
Page 153
START Power ON while pushing SCAN & OTHER keys. READY on LCD? Push “ ” key once. Push “ ” key once. Enter in Test Mode Enter in Service Setting Mode (To Section 9.6.1) (To Section 9.6.2) * Operation for the Item 1 * Each operation for the Items on the "...
Page 154
9.6.1 Service Setting Mode ( Service Mode 1 ) TOP PREVIOUS NEXT Mode - 1 Mode - 2 Mode - 3 TOP PREVIOUS NEXT...
Page 155
(From Section 9.6) (1) PCB Rev. No. (Disp. PCB Version and others) PCB Rev. No. Select a menu of Setting Item by MaOGsOIfOOGiOMeO pushing “ ” or “ ” key. Classification of SD RAM GA-IMG Ver. I/F Board Ver. Change the parameter of another I/F Board Name item?
Page 156
(From Section 9.6) (2) Clean Roller (Set counter for roller cleaning timing) (3) Replace Roller (Set counter for roller replacement timing) (4) Detect Size (5) Adjust value for Length manually (6) Adjust value for Front V. Position manually Select a menu of Setting Item by (7) Sensor Delay pushing “...
Page 157
(From Section 9.6) (11) Set Default Select a menu of Setting Item by pushing key. “ ” “ ” Set Default? Pushing keys changes setting “ ” “ ” Push keys “ ” “ ” on LCD into default except for the following contents. once at the same time.
Page 158
9.6.2 Test Mode ( Service Mode 2 ) TOP PREVIOUS NEXT Mode - 1 Mode - 2 Mode - 3 Mode - 4 Mode - 5 Mode - 6 Mode - 7 TOP PREVIOUS NEXT...
Page 161
(From Section 9.6) (2) F. CIS LED / B. CIS LED (3) F. CIS Black Level / B. CIS Black Level (15) Double Feed (Check double feed sensitivity after setting input-level) Select a menu of Setting Item by “ ” “...
Page 162
(4) Document Sensor (From Section 9.6) (Check each document sensor condition) (5) Sensor Sensitive Level (6) Door & Home Sensor (12) Memory Test (13) Sleep Mode Select Sensor Test ((4) or (5) or (6) or (11) or (12)) Select a menu of Setting Item by pushing “...
Page 164
(From Section 9.6) (16) Adjust Double Feed Detector (17) Adjust Length Automatically Select a menu of Setting Item by (18) Adjust Front V. position pushing “ ” or “ ” key. Automatically (19) Adjust Front H. position (16) Set Adjustment paper. Automatically (17)-(22) Set Test chart A.
Page 165
(From Section 9.6) (14) Init. EEPROM This test is used only in case EEPROM has some errors * Please be very careful as this test Select a menu of Setting Item by operation initializes all data pushing “ ” or “ ”...
Page 166
(11) DIMM SPD (Serial Presence Detect) (From Section 9.6) Information Select a menu of Setting Item by pushing “ ” or “ ” key. 11. DIMM SPD Confirm the DIMM information by Byte xx Value xx pushing “ ” and “ ”...
9.7 Error Code TOP PREVIOUS NEXT TOP PREVIOUS NEXT...
Page 169
Error Code Classified ST1 ST2 ST3 ST4 Content Code 00 No Paper Error 00 Paper Feed Jam (when paper does not reach Waiting Sensor): ST2 shows the rest numbers (approx.) of paper. 00 Jam 1 (when paper does not reach Starting Position Sensor): ST2 shows the rest numbers (approx.) of paper.
Page 170
Classified ST1 ST2 ST3 ST4 Content Code 00 Front-side Lamp Lighting Error (STS2: Lighting Value, STS3: AD input value) 00 Back-side Lamp Lighting Error (STS2: Lighting Value, STS3: AD input value) 00 Scanning Position Adjustment (Auto Mode) Error 00 Program ROM Error on MAIN CONTROL Board Work RAM Error on MAIN CONTROL Board (ST2: Data, ST3,4: Address) 00 On Board DRAM Error 00 DIMM1 Error...
10 TROUBLESHOOTING TOP PREVIOUS NEXT Error Codes are listed in section 9.7 Error Code. Test the check points in order from the first entry. Error Code Possible Cause Check Point Program ROM Error on MAIN CONTROL Board • Replace the Program ROM •...
Page 173
Starting Position Sensor Error • Remove any dust on the LED on the STARTING POSITION LED Board, or on the light receptor on the STARTING POSITION SENSOR Board • Check that the LED on the STARTING POSITION LED Board,the light receptor on the STARTING POSITION SENSOR Board and the slot location on the carrier board are properly aligned •...
Page 174
• Replace the MAINCONTROL Board Ending ( Front ) Position Sensor Error • Remove any dust on the LED on the ENDING (FRONT) LED Board, or on the light receptor on the ENDING (FRONT) SENSOR Board • Check that the LED on the ENDING (FRONT) LED Board, the lightreceptor on the ENDING (FRONT) SENSOR Board and the slot location on the carrier board are properly aligned •...
Page 175
Double Feed Detector Error • Remove any dust on the Supersonic Receiver on the WAITING LED Board, or on Supersonic Generator on the WAITING SENSOR Board • Check that the Supersonic Receiver on the WAITING LED Board,Supersonic Generator on the WAITING SENSOR Board •...
Page 176
EEPROM Replace MAIN Control check Error Board MAIN Board Replace MAIN Control Error Board (Another model MAIN Board is supplied.) No Error Requirement after parts replacement Following adjustments are required when print circuit board or part is replaced. Replaced print circuit board or par t Required adjustment Adjust Shading Adjust All Position &...
Page 177
Disassemble and assemble which influence to Adjust All Position & Length Automatically or 4 Adjustments should be done. scanning positions. (1) Adjust Front H. Position Automatically EX) Disassemble and assemble of Sub Chassis (R), (2) Adjust Front V. Position Automatically (L), Main Chassis (R), (L) (3) Adjust Back H.Position Automatically (4) Adjust Back V.
Page 178
11 BLOCK DIAGRAM TOP PREVIOUS NEXT TOP PREVIOUS NEXT...
12 EXPLANATION of CONNECTOR TOP PREVIOUS NEXT TOP PREVIOUS NEXT...
Page 181
CN1000 (MAIN) - (CIS [FRONT]) Pin No. Signal Name Description Pin No. Signal Name Description CIS IN1 Contact Image Sensor Signal1 Ground AGND Analog Ground CCD(RST) Not Used CCD(P2) Not Used CCD(P1) Not Used Ground CISSP1 Start Pulse1 for CIS CCDDET2 Not Used Ground...
Page 182
CN1006 (MAIN) - CN2001(MOTHER)(continued) Pin No. Signal Name Description Pin No. Signal Name Description Ground Chip Select for Door Sensor Chip Select for Key Ground Chip Select for Key Chip Select for Size Sensor CN600(SCSI) Ground Pin No. Signal Name Description Ground Ground...
Page 183
CN601(SCSI) (continued) Pin No. Signal Name Description Pin No. Signal Name Description Ground Ground Ground Ground CPUA8 CPU Adress Ground Ground CPUA7 CPU Adress N.C. N.C. CPUA6 CPU Adress CPUA5 CPU Adress N.C. N.C. N.C. N.C. CPUA4 CPU Adress Ground CPUA3 CPU Adress CPUA2...
Page 184
CN2003(MOTHER) - CN331(DRIVE) Pin No. Signal Name Description Pin No. Signal Name Description SKEW Sensor Comparater Level Ground DACDI DAC Data PREDOOR Pre Imprinter Door Sensor input DACCLK DAC Clock +5VS DACLD DAC Load Ground +5VS +38V +38V Ground SKEW LEVEL Skew Sensor LEVEL control output Ground AN3(EXIT)
Page 185
CN2008(MOTHER) - Post Imprinter(continued) Pin No. Signal Name Description Pin No. Signal Name Description +38V +38V SIZE2 Paper Size Sensor2 +12VS +12V Ground SIZE1 Paper Size Sensor1 Ground LEVER Retard Position Sensor CN2009(MOTHER) - CN862(DC-DC CONVERTER) Paper Detector Pin No. Signal Name Description HOPPER...
Page 186
CN515(POINTER DETECTOR) - CN516(ENDING[REAR]) Pin No. Signal Name Description Pin No. Signal Name Description Ground Conveyor Motor Phase-A Conveyor Motor Phase-B(-) EXIT R Ending (Rear) Position Sensor CCOMB +24V for Conveyor Motor JAM LED Paper JAM LED Output Conveyor Motor Phase-B N.C.
Page 187
13 CIRCUIT BOARDS TOP PREVIOUS NEXT 13.1 MAIN CONTROL Board (Component Side) 13.2 MAIN CONTROL Board (Solder Side) 13.3 SCSI Board (Component Side) 13.4 SCSI Board (Solder Side) 13.5 MOTHER Board 13.6 DRIVE Board (Component Side) 13.7 DRIVE Board (Solder Side) 13.8 PANEL Board 13.9 RELAY (LOWER) Board 13.10 RELAY (UPPER) Board...
Page 188
13.19 STARTNG POSITION SENSOR Board 13.20 WAITING SENSOR Board 13.21 ENDING (FRONT) SENSOR Board 13.22 PAPER JAM SENSOR Board 13.23 ENDING (FRONT) LED Board 13.24 POST IMPRINTER DOOR Board 13.25 DC-DC CONVERTER Board 13.26 POWER Board TOP PREVIOUS NEXT...
14 SCHEMATIC DIAGRAM TOP PREVIOUS NEXT Index 14.1 MAIN CONTROL Board 14.2 SCSI Board 14.3 MOTHER Board 14.4 DRIVE Board 14.5 PANEL Board 14.6 RELAY LOWER and UPPER Boards 14.7 Sensor Boards 14.8 DC-DC CONVERTER and POWER Board Note: This Schematic Diagram is the latest at the time of printing and subject to change without notice. 14.1 MAIN CONTROL Board 14.2 SCSI Board 14.3 MOTHER Board...
Page 242
14.5 PANEL Board 14.6 RELAY LOWER and UPPER Boards 14.7 SENSOR Boards 14.8 DC-DC CONVERTER and POWER Boards TOP PREVIOUS NEXT...
15 PARTS LOCATION AND MECHANICAL PARTS LIST TOP PREVIOUS NEXT Note: RTL (Retention Time Limited) The marking (RTL) in the Remark column indicates that the Retention Time is limited for this item. After the discontinuation of this assembly in production, the item will continue to be available for a specific period of time.
Page 273
15.2 Power Unit and Circuit Board 15.3 Chassis and Base 1 15.4 Chassis and Base 2 15.5 Packing 15.6 Tool TOP PREVIOUS NEXT...
Page 275
Hopper Base (ISO Code:ABS) PJHRB0006Z-J Hopper Plate (For KV-S2065L) (ISO Code:ABS) PJHRB006Z-J1 Hopper Plate (For KV-S2065W) (ISO Code:ABS) PBHRA0194Z-J Paper Guide (R) (For KV-S2065L) (ISO Code:ABS) PBHRA194Z-J1 Paper Guide (R) (For KV-S2065W) (ISO Code:ABS) PBHRA0193Z-J Paper Guide (L) (For KV-S2065L) (ISO Code:ABS) PBHRA193Z-J1...
Page 276
PJBAB0007Z Exit Guide L (ISO Code:ABS) PBMDA0573Z Reflector Fitting Plate PJJRB0617Z Cable (CN531-PHOTO INTERRUPTER) PBHRA0191X Function Key (ISO Code:ABS) PJQTA0652Z Label PJGTB0012Z Name Plate (For KV-S2065L) PJGTB0002Z Name Plate (For KV-S2065W) XTB3+6FFX Screw XTS3+10GFX Screw XTW3+U10PFX Screw XTW3+U10PFY Screw XTW3+U6LFX...
15.2 Power Unit and Circuit Board TOP PREVIOUS NEXT...
Page 279
REPLACEMENT MECHANICAL PARTS LIST (Power Unit and Circuit Board) Ref. No. Part No. Part Name & Description Remarks PBJEA0090Z PBAPX012065A POWER Board (RTL) PJJRB0615Z AC Inlet Cable PJJRB0608Z Power Unit Relay Cable (CN861-CN802) PBMCX0086Y Power Box Assembly PJHXB0002Z POWER Board Sheet (ISO Code:PVC) PJJRB0616Z AC Switch Cable PBAPX062065A MOTHER Board...
Page 282
15.3 Chassis and Base 1 TOP PREVIOUS NEXT...
Page 283
REPLACEMENT MECHANICAL PARTS LIST (Chassis and Base1) Ref. No. Part No. Part Name & Description Remarks PBUAX0115Z Sub Chassis (R) PBUAX0114Z Sub Chassis (L) PBHAA0034Z Inside Conveyor (ISO Code:ABS) PBAPX263255B ENDING (FRONT) POSITION (LED) Board (RTL) PBAPX276255B PAPER JAM SENSOR Board (RTL) PBJEA0545Z Cable (CN527-CN528)
Page 285
PBUL30Z Lock Release Plate PBUSA0038Z Conveyor Spring PBHEA0107Z Sub Sheet for KV-S2065L (ISO Code:PVC) PBDRA0112Y-J Sensor Roller for KV-S2065L PBDRA0101X-J Sensor Roller for KV-S2066W PBDRA0073Z Platen Pitch Roller (ISO Code:POM) PBDJA0014Z Platen Spacer PJNW4111Z Spacer PBDSA0036Y Spring PBDGA0061Z Platen Gear (ISO Code:POM)
Page 286
PJDSB0005Z Free Roller Pressure Spring PJJRB0601Y Cable PJQTB0003Z Transport Label 1 PJQTB0004Z Transport Label 2 PJJRB0660Z Cable XVP4F20FX Wing Bolt XPJ2C10VW XTW3+U6LFX Screw XTW3+U8PFX Screw XUC5FY E-Ring XUC6FY E-Ring XYN26+C6FX Screw XYN3+B6FX Screw for KV-S2065L XYN4+F10FX Screw TOP PREVIOUS NEXT...
Page 287
15.4 Chassis and Base 2 TOP PREVIOUS NEXT...
Page 288
REPLACEMENT MECHANICAL PARTS LIST (Chassis and Base2) Ref. No. Part No. Part Name & Description Remarks PBDFA0094Z Pointer Shaft PBUSA0035Y-J Roller Shaft Assembly PBDRA0029Z Free Roller (ISO Code:POM) PBHMA0133Z Pointer Change Plate PBHRA0117Z Pointer (ISO Code:PC) EDS-1717u Edge Saddle PBAPX277255B POINTER DETECTOR Board (RTL) PBAPX274255B...
Page 290
Belt Holder (ISO Code:PA) PBMDX0468Z Tension Plate Assembly PBDGA0061Z Platen Gear (ISO Code:POM) PBDJA0020Z Platen Spacer PBDRA0073Z Platen Pitch Roller (ISO Code:POM) PBDRA0013Y-J Sensor Roller for KV-S2065L PBDRA0102X-J Sensor Roller for KV-S2065W PJNW4111Z Spacer SS-5GL-3T Micro Switch B80S2M530 Belt EQ4R219Q1...
Page 291
PBHEA0107Z Sub Sheet KV-S2065L only (ISO Code:PVC) PBMDA0455Z Gas Spring Fitting Plate PBDSA0099Z Platen Hold Spring (R) PBUS8Z Conveyor Spring PBDSA0079Z Conveyor Lock Spring (R) PBDSA0080Z Conveyor Lock Spring (L) TB-9513 Bush PBFV4Z Bushing (ISO Code:POM) TB-2533 Bush TB-1926 Bush...
Page 292
RWPS8-025 Spacer B-F8-8 Spacer PBDFA0110Z Retard Unit Fitting Shaft) F-FLAW678AZZ Bearing2 B-S8-5 Spacer RWPS10-100 Spacer PBDSA0125Z Spring PBDSA0092Z Retard Pressure Spring PBDGA0055Z Separation Drive Gear PBHRA0183Z Adjusting Knob (ISO Code:ABS) PBDFA0100Y Retard Regulation Shaft PBDG3Z Cam (ISO Code:POM) NF-2G50C Oil Damper PBUEX0097Z-J Conveyor (Lower) 1 Assembly PBULA0129Z...
Page 293
PBDGA0059Z Pulley Gear (ISO Code:POM) PBDSA0100Z Spring PBDSA0106Z Spring PBUSA0034Z Pointer Change Spring PBDGA0038Z Retard Gear (ISO Code:POM) PBDGA0032Z Gear (ISO Code:POM) PBDSA0103Z Hopper Spring2 PBDSA0096Z Hopper Spring1 PBULA0130Z Reinforcement Plate (L) 2 RWPS5-10025 Spacer B-S6-146 Spacer RWPS6-050 Spacer PBHEA0141Z Sheet Cover PBHEA0111Z Sheet Cover...
Page 296
15.5 Packing TOP PREVIOUS NEXT TOP PREVIOUS NEXT...
Page 297
15.6 Tool TOP PREVIOUS NEXT REPLACEMENT MECHANICAL PARTS LIST (Packing) Ref. No. Part No. Part Name & Description Remarks PJPGB0004Z-L Outer Carton for S2065L PJPGB0004Z-W Outer Carton for S2065W HP-601W2 Joint (ISO Code:PP) PBPGA0322Y Carton PJQXB0001Z Installation Manual/Driver Software PJQMB0021Z Maintenance Manual PBQX70014Z Warranty Card...
Page 298
PBQX90113Z-J Shading Paper (10 pieces) PBQX90121Z-J Adjustment Paper (50 pieces) PBQX90104Z-J Test Chart A (10 pieces) PBQX90105Z-J Test Chart B (10 pieces) T4E30725-2 Polyester tape (19 mm) T4E307100 Polyester tape (100 mm) TOP PREVIOUS NEXT...
Page 299
16 ELECTRICAL REPLACEMENT PARTS LIST TOP PREVIOUS NEXT Note: RTL (Retention Time Limited) The marking (RTL) in the Remark column indicates that the Retention Time is limited for this item. After the discontinuation of this assembly in production, the item will continue to be available for a specific period of time. The retention periodof availability is dependent on the type of assembly, and in accordance with the laws governing part and product retention After the end of this period, the assembly will no longer be available.
Page 328
16.10 WAITING [LED] Board TOP PREVIOUS NEXT Ref. No. Part No. Part Name & Description DIODES D505-507 TLN119 OTHERS CN522 S8B-PH-K-S Connector X501 MA40S4R Supersonic Wave Sensor PBHRA0055Z Spacer PBHRA0201Z Spacer TOP PREVIOUS NEXT...
Page 329
16.11 POINTER Board TOP PREVIOUS NEXT Ref. No. Part No. Part Name & Description RESISTORS R553 ERDS2TJ331 330 / J / 0.25W R554 ERDS2TJ103 10k / J / 0.25W CAPACITORS C523 RPE132F104 Capacitor TRANSISTORS Q524 2SC3311A Transistor IC513 TLP832 Photo Interrupter OTHERS CN514 PBB7B-PH...
Page 330
16.12 ENDING ( REAR ) SENSOR Board TOP PREVIOUS NEXT Ref. No. Part No. Part Name & Description RESISTORS R555 ERDS2TJ103 10k / J / 0.25W CAPACITORS C524 ECBT1H102KB5 1000P / 50V C525 RPE132F104 Capacitor C526 ECBT1H102KB5 1000P / 50V C560 RPE122E105 Capacitor...
Page 331
16.13 PAPER JAM (LED) Board TOP PREVIOUS NEXT Ref. No. Part No. Part Name & Description DIODES D502 TLN119 OTHERS CN518 PBB5B-PH Connector PBHRA0055Z Spacer TOP PREVIOUS NEXT...
Page 332
16.14 START POSITION [LED] Board TOP PREVIOUS NEXT Ref. No. Part No. Part Name & Description DIODES D503 TLN119 OTHERS CN519 S5B-PH-K-R Connector CN520 PBS4B-PH Connector PBHRA0055Z Spacer TOP PREVIOUS NEXT...
Page 333
16.15 ENDING ( REAR ) LED Board TOP PREVIOUS NEXT Ref. No. Part No. Part Name & Description DIODES D504 TLN119 OTHERS CN521 PBS4B-PH Connector PBHRA0055Z Spacer TOP PREVIOUS NEXT...
Page 334
16.16 STARTING POSITION SENSOR Board TOP PREVIOUS NEXT Ref. No. Part No. Part Name & Description RESISTORS R556 ERDS2TJ103 10k / J / 0.25W CAPACITORS C527 RPE132F104 Capacitor C528/529 ECBT1H102KB5 1000P / 50V C561 RPE122E105 Capacitor TRANSISTORS Q527 2SC3311A Transistor Q528 PN168 Photo Transistor...
Page 335
16.17 WAITING SENSOR Board TOP PREVIOUS NEXT Ref. No. Part No. Part Name & Description RESISTORS R557-559 ERDS2TJ103 10k / J / 0.25W CAPACITORS C530 RPE132F104 Capacitor C531-532 ECBT1H102KB5 1000P / 50V C533 RPE132F104 Capacitor C534-537 ECBT1H102KB5 1000P / 50V C545 RPE132F104 Capacitor...
Page 336
16.18 ENDING (FRONT) SENSOR Board TOP PREVIOUS NEXT Ref. No. Part No. Part Name & Description RESISTORS R561 ERDS2TJ103 10k / J / 0.25W CAPACITORS C541 RPE132F104 Capacitor C542/543 ECBT1H102KB5 1000P / 50V C566 RPE122E105 Capacitor TRANSISTORS Q537 2SC3311A Transistor Q538 PN168 Photo Transistor...
Page 337
16.19 PAPER JAM SENSOR Board TOP PREVIOUS NEXT Ref. No. Part No. Part Name & Description RESISTORS R560 ERDS2TJ103 10k / J / 0.25W CAPACITORS C538 RPE132F104 Capacitor C539/540 ECBT1H102KB5 1000P / 50V C565 RPE122E105 Capacitor TRANSISTORS Q535 2SC3311A Transistor Q536 PN168 Photo Transistor...
Page 338
16.20 ENDING (FRONT) LED Board TOP PREVIOUS NEXT Ref. No. Part No. Part Name & Description DIODES D508 TLN119 OTHERS CN528 ILS4PS2L2EF Connector PBHRA0055Z Spacer TOP PREVIOUS NEXT...
Page 339
16.21 POST IMPRINTER DOOR Board TOP PREVIOUS NEXT Ref. No. Part No. Part Name & Description RESISTORS R562 ERDS2TJ103 10k / J / 0.25W R563 ERDS2TJ331 330 / J / 0.25W CAPACITORS C544 RPE132F104 Capacitor TRANSISTORS Q539 2SC3311A Transistor IC514 TLP832 Photo Interrupter OTHERS...
Page 340
16.22 DC-DC CONVERTER Board TOP PREVIOUS NEXT Ref. No. Part No. Part Name & Description RESISTORS R861 ERDS2TJ683 68k / J / 0.25W R862 ERDS2TJ682 6.8k / J / 0.25W R863 ERX12SJR56 0.56 / J / 0.5W R864 ER0S2TKF5762 57.6k / F / 0.25W R865 ER0S2TKF1242 12.4k / F / 0.25W...
17 Schematic Diagram for printing with A4 size TOP PREVIOUS NEXT 17.1 MAIN CONTROL Board 17.2 SCSI Board 17.3 MOTHER Board 17.4 DRIVE Board 17.5 PANEL Board 17.6 RELAY LOWER and UPPER Boards 17.7 SENSOR Boards 17.8 DC-DC CONVERTER and POWER Boards TOP PREVIOUS NEXT...
Page 347
17.1 MAIN CONTROL Board TOP PREVIOUS NEXT TOP PREVIOUS NEXT...